• 한국CDE학회논문집
• /
• 제18권5호
• /
• pp.367-373
• /
• 2013

In this study, the penetration characteristic from the cubic and cylindrical penetrator consisting of tungsten material with the velocity of 2,300 m/s is evaluated and the penetration possibility into the target is confirmed. The design of shape and size of penetrator is directly related to space and weight of the warhead. AUTODYN-3D simulation is used to study the penetration effect of penetrator. The purpose of numerical analysis is to verify the penetration characteristic with various L/D penetrator. The penetration performance of penetrator with identical weight due to the shape is also confirmed. The cylindrical and cubic penetrator has enough penetration energy on constant target body. Because the possibility of 2'nd penetration is important factor after 1'st penetration into target body, residual velocity of residual mass must be existed as much as possible. As geometrical shape ratio increases, penetration performance is confirmed to improve.

• 한국시뮬레이션학회논문지
• /
• 제27권3호
• /
• pp.109-116
• /
• 2018

견고표적을 무력화하기 위해서는 높은 침투/관통성능을 가진 침투탄의 개발이 필수적이다. 침투탄의 설계를 위해, 본 논문에서는 노즈 형상 인자들이 침투자의 콘크리트 침투/관통성능에 미치는 영향을 분석하였다. 전산해석은 상용 전산해석 프로그램인 AUTODYN-2D를 사용하여 수행하였다. Forrestal의 시험결과를 사용하여 전산해석의 신뢰성을 검증하였으며, 침투자의 노즈 형상보다는 노즈 길이가 침투/관통성능에 더 큰 영향을 미치는 것을 확인하였다. 또한, 침투자의 노즈 길이가 일정할 경우, 노즈 팁 직경을 특정값까지 증가시켜 침투/관통성능을 향상시킬 수 있음을 확인하였다.

• Journal of Welding and Joining
• /
• 제27권2호
• /
• pp.44-50
• /
• 2009

The characteristics of arc pressure, current density and heat flux distribution are important factors in understanding physical arc phenomena, which will have a marked effect on the penetration, size and shape of a weld in TIG welding. The purpose of this study is to find out the effect of the heat flux on the melting efficiency and penetration shape in TIG welding using the results of the previous investigators. The conclusions obtained permit to draw a proper method which derived the heat flux distributions by arc pressure distribution measurements, but previous researchers calculated heat flux and current distribution with the heat intensity measurements by the calorimetry. Heat flux of Ar gas arc was concentrated at the central part and distributed low from the arc axis to the radial direction, that of He mixing arc was lower than that of Ar gas, and it was wide distributed to radial direction. That showed a similar characteristic with the Nestor's by calorimetry calculated values. Throughout heat flux drawn in this study was discussed melting efficiency and penetration shape on Ar gas and He mixing gas arc.

• 대한기계학회논문집A
• /
• 제29권1호
• /
• pp.30-37
• /
• 2005

There is few research about contact problem for a rigid surface with an arbitrary shape in SPH. The variational equation based on the virtual work principle is derived and its solution is obtained by the penalty method. It is proposed a new method that can determine the parameters for a penetration and a penetration rate used in the penalty method. The reproducing condition is adopted to correct the deficiency of kernel on the boundary. In order to calculate a penetration of particles, after checking boundary particles for deformable body, boundary normal vectors were determined on the rigid surface. Numerical simulations for models which have rigid surface with an arbitrary shape were conducted to validate the proposed method in 2D Cartesian and cylindrical coordinate. The results of those analysis represent that the contact algorithm proposed in this study works properly.

• 펄프종이기술
• /
• 제34권3호
• /
• pp.25-31
• /
• 2002

The purpose of this study was to analyze how the fiber properties and mixing ratio of softwood and hardwood pulp affect on roundness of printed image. Softwood pulp and hardwood pulp were refined to 400 and 600ml CSF by Valley beater and handsheets of 70 g/$m^2$ basis weight were made at different mixing ratios of hardwood and softwood pulp. The roundness, dot area, and shape of the printed dot were measured by Image Analyzer. The depths and shapes of the acridine orange penetration into paper were measured by CLSM. With higher mixing ratio of hardwood pulp, the paper showed higher air-permeability and better formation, especially at lower freeness. The roundness of the printed image became better and the dot size became smaller when the amount of hardwood pulp increased. Penetration depth of acridine orange by CLSM became greater and roundness increased to real circle when the amount of hardwood pulp increased. It was thought that higher mixing ratio of hardwood fibers resulted in efficient penetration by better formation with uniform micro-pore distribution and it increased roundness. It was thought that fiber properties and mixing ratio affected the structure of paper and the shape of the printed dot. This study showed that the measurement of depth of the liquid penetration into paper without destruction and contact was feasible. Moreover, this method showed that the shape of the liquid penetration was measurable.

• 한국해양공학회지
• /
• 제11권3호
• /
• pp.29-38
• /
• 1997

Crack penetration behavior by fatigue crack propagation and measurements of AE before-and-after crack penetration were examined using SS41 steel plate. Experimental crack shape of SU type was in good agreement with calculated shape rather than S type. Crack propagation behavior on the front surface appears not to change markedly after penetration. However, crack growth on the back surface appears to accelerate as reported by author. As a crack propagates, AE occurred heavily just before penetration. Then, it decreases and crack is penetrating. A transition from plane strain to plane stress was observed by fractographic study. At this time, separation of fracture surface was shown which affects AE occurrence.

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.1990-2001
• /
• 1991

본 연구에서는 평활부 및 응력집중부에 표면균열을 갖는 표면균열재의 피로수 명과 균열관통 거동을 검토하고, 그 특성을 해명하였다.

• International Journal of Korean Welding Society
• /
• 제3권1호
• /
• pp.8-16
• /
• 2003

A major concern in Gas Metal Arc (GMA) welding process is the determination of welding process variables such as wire diameter, gas flow rate, welding speed, arc current and welding voltage and their effects on the desired weld bead dimensions and shape. To successfully accomplish this objective, 81 welded samples from mild steel AS 1204 flats adopting the bead-on-plate technique were employed in the experiment. The experimental results were used to develop a mathematical model to predict the magnitude of bead geometry as follows; weld bead width, weld bead height, weld bead penetration depth, weld penetration shape factor, weld reinforcement shape factor, weld bead total area, weld bead penetration area, weld bead reinforcement area, weld bead dilution, length of weld bead penetration boundary and length of weld bead reinforcement boundary, and to establish the relationships between weld process parameters and bead geomery. Multiple regression analysis was employed for investigating and modeling the GMA process and significance test techniques were applied for the interpretation of the experimental data.

• 대한조선학회논문집
• /
• 제49권6호
• /
• pp.469-477
• /
• 2012

This paper describes the characteristic analysis of ice impact force for the Arctic structure shape. In the present study an energy method has been used to predict the impact force during the ice-structure collision. This study also employs two concepts for reference contact area and normalized stress in analysis procedure. The influences of factors, such as impact velocity, full penetration depth, structure shape and ice floe size, are investigated. Full penetration occurs, particularly at lower impact velocity when ice thickness increase. But "typical size" ice floe does not expected ever to achieve full penetration during the impact procedure. The structure shape is the dominant factor in ice impact force characteristic. The results for various ice-structure collision scenarios are analyzed.

• 수산해양기술연구
• /
• 제28권2호
• /
• pp.197-207
• /
• 1992

Fatigue life and penetration behavior were examined analytically by variety of initial front face crack length and initial crack depth. The fatigue crack shape before penetration is almost semielliptical, and the aspect ratio by calculation using the Newman-Raju's formula is smaller than the value obtained by the experiment. It is found that the crack growth behavior on the back surface after penetration is unique and can be divided into three stage a, b and c. By using the K value proposed by the authors, particular crack growth behavior and the change in crack shape can be evaluated quantitatively. It is found that fatigue life and penetration behavior were more dependent on initial front face crack length than initial crack depth.