• Asian-Australasian Journal of Animal Sciences
• /
• v.28 no.9
• /
• pp.1317-1326
• /
• 2015

This study investigated the metabolizable energy (ME) intake, net energy of production (NEp), heat production (HP), efficiencies of ME use for energy, lipid and protein retention as well as the performance of broiler chickens fed diets based on cassava chips or pellets with or without supplementation with an enzyme product containing xylanase, amylase, protease and phytase. The two products, cassava chips and pellets, were analysed for nutrient composition prior to feed formulation. The cassava chips and pellets contained 2.2% and 2.1% crude protein; 1.2% and 1.5% crude fat; and 75.1% and 67.8% starch, respectively. Lysine and methionine were 0.077%, 0.075%, and 0.017%, 0.020% protein material, respectively, while calculated ME was 12.6 and 11.7 MJ/kg, respectively. Feed intake to day 21 was lower (p<0.01) on the diet containing cassava chips compared to diets with cassava pellets. Enzyme supplementation increased (p<0.01) feed intake on all diets. Live weight at day 21 was significantly (p<0.01) reduced on the diet based on cassava chips compared to pellets, but an improvement (p<0.01) was noticed with the enzyme supplementation. Metabolizable energy intake was reduced (p<0.01) by both cassava chips and pellets, but was increased (p<0.01) on all diets by enzyme supplementation. The NEp was higher (p<0.01) in the maize-based diets than the diets containing cassava. Enzyme supplementation improved (p<0.01) NEp in all the diets. Heat production was highest (p<0.01) on diets containing cassava pellets than on cassava chips. It is possible to use cassava pellets in diets for broiler chickens at a level close to 50% of the diet to reduce cost of production, and the nutritive value of such diets can be improved through supplementation of enzyme products containing carbohydrases, protease, and phytase.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1780-1782
• /
• 2001

In this experiment, an attempt to use the sludge pellets as catalyst for NO removal from simulated gas is experimentally investigated by using $BaTiO_3$-sludge packed-bed reactor of plate-plate geometry. An experimental investigation has been conducted for NO concentration of 50[ppm] balanced with air, a gas flow rate of 5[1/min]. $BaTiO_3$ pellets are filled at upstream of reactor for corona discharge and sludge pellets are put at downstream of reactor for catalystic effect. The volume rate of sludge pellets to $BaTiO_3$ pellets is 50[%] and AC voltage to dischare the gases was supplied. In the result, when sludge pellets is seperated to $BaTiO_3$ by other reactor and AC voltage is supplied to $BaTiO_3$ and sludge pellets NO, $NO_2$ removal rate is higher. When gas temperature increase from room temperature to 100[$^{\circ}C$], NO removal is decreased while $NO_2$ concentration is independent on gas temperature. This result suggest that the removal mechanism of active oxyzen species and $NO_2$ in sludge is not absorption, but chemical reaction. Temperature of heating treatment is on sludge pellets increased, $NO_x$ removal rate is decrease. It is thought that organic compound is removed by heating treatment.

• The Plant Pathology Journal
• /
• v.19 no.2
• /
• pp.92-96
• /
• 2003

The study was conducted to determine the cultural conditions and the effect of inert fillers for melanization and sporulation abilities of sodium alginate pellets, and the weeding efficacy of the formula in the field. Melanin production of E. nematosporus was affected by striking frequency. Percentage of melanized beads was increased to 80.6% at higher rpm up to 180. The melanized pellets produced more conidia with abundant mucilage than unmelanized pellets. Shaker culture of Epicoccosorus nematosporus with sodium alginate yielded a total of 55 mg per 100 pellets. Percentage of melanized pellets was highest with 81.0% and 83.3% of melanization, when wheat bran and rice polish were amended and produced the conidia with 65.4 and 68.4 mg per 100 pellets, respectively. When 1 L of conidial suspension of 6.0$\times$$10^5$ conidia per ml was applied on 30-day-old plants in a plot, 74.5% of the plants were killed within 20 days, whereas, its melanized sodium alginate pellets killed 57.8% of the plants in the same period. The number of tuber formation of Eleocharis kuroguwai in the untreated control plots was 128.5 per plot, but those of the plots treated with conidial suspension and melanized pellets were 22.1 and 39.7, respectively, at the end of the season. Results of this study showed that melanization of mycelia-mixed sodium alginate are an important sporulation factor in E. namatosporus as a mycoherbicide.

• YAKHAK HOEJI
• /
• v.41 no.1
• /
• pp.48-59
• /
• 1997

Sustained release matrix tablets, pellets, and coated pellets for the delivery of sulindac were prepared using cellulose derivatives at various ratios, and evaluated for the dis solution pattern. The release of sulindac, from matrix tablets prepared with low viscosity HPMC was relatively fast, and especially the tablets made of Metolose SM released all of sulindac within 1 hr. The release of drug from tablets made of other HPMC derivatives were retarded in the order of the following: Pharmacoat 645>Pharmacoat 606>Pharrnacoat 606+HPC-L>HPC-L. The most sustained release pattern was observed with the preparation of high viscous polymer. Metolose 90 SH. While release of sulindac, from matrix type pellet containing 10mg/cap of Metolose 90 SH or 60 SH was completed within 1 hr, a prolonged release formulation (30% in 1 hr) was obtained by the inclusion of EC. Pellets coated with HPMC showed a fast release pattern (${\geq}$ 80% within 2 hrs), whereas pellets coated with HPMC and EC (molar ratio 1 : 1) showed a sustained release pattern (${\geq}$ 80% in 12 hrs), vath the release from EC pellets being the most sustained. Fast (naked) and slow release pellets coated with EC, Metolose 60SH 50cps and propylene glycol. and enteric pellets coated with HPMCP 55 and Myvacet$^{\circledR}$ were prepared, and combined at various ratios for the assessment of dissolution pattern. The result indicates the possibility that the development of 24 hr sustained release delivery systems containing sulindac for oral administration could be achieved by means of combining sustained and fast release pellets at a proper portion.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.53 no.2
• /
• pp.61-65
• /
• 2011

Biomass is considered to be a major potential fuel and renewable resource for the future. In fact, there is high potential to produce the large amount of energy from biomass around the world. In this study, to obtain basic data for practical application of agricultural and forest by-products as fuel of heating system in agriculture, agricultural and forest biomass resources were surveyed, the pelletizer with capacity of $50\;kg{\cdot}h^{-1}$ was designed and manufactured and pellets were made by the pelletizer. High heating value, ash content, etc. of pellets made of agricultural and forest by-products were estimated. Straw of rice was the largest agricultural biomass in 2009 and the total amount of rice straw converted into energy of $299{\times}10^3$ TOE. And in 2009, amount of forest by-product converted into energy of $9,579{\times}10^3$ TOE. High heating values of pellets made of stem and seed of rape, stem of oat, rice straw and rice husk were 16,034, 16,026, 16,089, 15,650, $15,044\;kJ{\cdot}kg^{-1}$ respectively. High heating values of pellets made of agricultural by-products were average 83.6% compared to that of wood pellet. Average bulk density of pellets made of stem and seed of rape, stem of oat, rice straw and rice husk was $1,400\;kg{\cdot}m^{-3}$ ($1.4\;g{\cdot}cm^{-3}$). Ash contents of the pellets were 6.6, 7, 6.2, 5.5, 33% respectively. Rice husk pellet produced the largest ash content compared to other kinds of pellets.

• New & Renewable Energy
• /
• v.18 no.2
• /
• pp.1-8
• /
• 2022

This study aimed to determine the optimal conditions for fabricating pitch pine (PCP) and Mongolian oak (MOK) pellets using chestnut-shell tea waste (CSW) and castor oil (CSO) as additives. For pellets fabricated using a pilot-scale flat-die pellet mill, all moisture content (MC) was in line with A1 wood pellet standards for residential and small-scale commercial uses designated by the National Institute of Forest Science at the Republic of Korea (NIFOS), regardless of fabricating conditions; the durability of PCP pellets prepared using PCP particles with 10% MC, and CSW addition also satisfied these criteria. The moisture tolerance of PCP pellets improved with combination of 2 wt% CSW and 2-6 wt% CSO. Overall, use of 20 mesh CSW as an additive, PCP with 10% MC, and MOK with 12% MC was found to be optimal. Moreover, using CSO as an additive, high-quality PCP and MOK pellets can be fabricated by adjusting the particles to 12% MC. However, the durability of PCP and MOK pellets prepared using these conditions did not meet the wood pellet standards for residential and small-scale commercial use. Therefore, further research is needed to improve the durability of these pellets.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.1
• /
• pp.23-37
• /
• 2023

One type of biomass that has promising potential for bio pellet production is spent coffee grounds (SCGs). However, previous studies have shown that SCGs in bio pellets cause a lot of smoke. Therefore, they need to be mixed with a material that has a higher calorific value to produce better quality pellets. One material that can be used is pine wood because it has a natural resin content that can increase the calorific value. The aim of this study was to examine the quality of bio pellets produced with SCGs and pine wood charcoal at different particle sizes. The charcoal was ground using either a hammer mill (HM) or a ball mill (BM). Pine wood charcoal was mixed with SCGs at ratios of SCGs to pine wood charcoal of 4:6 and 6:4 by weight, respectively, and the adhesive used a tapioca with a composition ratio 5% of the raw material. The bio pellets were produced using a manual pellet press. The quality of the bio pellets was assessed based on Indonesian National Standard (SNI) 8021-2014, and the physical observations include flame length, burning rate, and compressive strength. The average water content, ash content, and calorific value of the bio pellets were in accordance with SNI 8021-2014, but the density and ash content values were below the standard values. The BM variation of bio pellets had a higher compressive strength than the HM variation, and the 4:6 BM variation had the longest burning time compared with 4:6 HM.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.6
• /
• pp.757-767
• /
• 2015

This study was conducted to investigate the effects of moisture content and particle size of sawdust on the fuel characteristics of wood pellets produced with Mongolian oak (Quercus mongolica, QUM), red pine (Pinus densiflora, PID) and larch (Larix kaempferi, LAK) sawdust using a flat-die pelletizer. Prior to produce wood pellets, the sawdust was controlled to the moisture content of 8, 11, 12% and was screened to the particle size of 2 and 4 mesh. In the analysis of its chemical composition, QUM had a high ash content, and PID and LAK contained large amount of lignin. In case of the fuel characteristics, PID pellets had the lowest moisture content of pellets (P-MC), and LAR pellets was found to have the highest bilk density (BD) and durability (DU). With the increase of moisture content of sawdust (S-MC), P-MC and DU of QUM, PID and LAK pellets increased, but BD of QUM and LAK pellets decreased. When size of sawdust used for the production of wood pellets decreased, P-MC and BD of LAK pellets and BD of QUM pellets increased. Decrease of particle size contributed to the increase of DU of QUM, PID and LAK pellets. In addition, BD and DU of QUM pellets produced with 12% S-MC sawdust increased as its particle size reduced. For LAK pellets, DU was not influence by particle size in the S-MCs of 10% and 12%, but increased with the decrease of particle size in the S-MC of 8%. Based on the results and economical aspects, 10% MC and 2 mesh paricle size for QUM sawdust and 12% MC and 2 mesh particle size for PID sawdust might be optimal conditions for pellets production, and fuel characteristics of wood pellets produced by the conditions greatly exceeded the minimum requirements for the $1^{st}$-grade wood pellets of the standard designated by Korea Forest Research Institute.

• Journal of the Korean Society of Safety
• /
• v.27 no.2
• /
• pp.20-24
• /
• 2012

Experimental studies were performed to investigate the eye injury risks by different BB pellet materials. Four different BB pellet materials were used: plastic (P), silicon (S), rubber (R) and plastic covered with silicon (SR). The BB pellet images penetrating into the gelatine simulant were recorded by a high-speed video camera. The results obtained from the different pellet materials were discussed in terms of impact velocity and penetration depth; threshold velocity and projectile sectional density; eye injury risks by normalized energies. It was found that the P pellets caused higher impact velocity while the lower was SR pellets. The penetration depth and threshold velocity of the pellets were dependent on the impact velocity of the pellets, and the P pellets resulted in the higher eye injury risk while the lower was SP.

• Journal of the Korean Society of Safety
• /
• v.26 no.3
• /
• pp.29-33
• /
• 2011

Experimental studies were performed to investigate the injury potential of BB pellets through gelatine based simulants. In order to record BB pellet movements penetrating into the target simulant, a high-speed video camera was used. In this study the first investigation involved the effects on concentrations, homogeneity and gelation times of the gelatine simulant. The second investigation involved the penetration depth of the pellets to the simulant by different distances between the BB gun and the simulant. The final one is associated with impact velocity, threshold velocity and penetration depth of the pellets by different kinetic energies of the BB gun. Results provided the basis in assessing the injury potential of BB pellets.