• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1391-1393
• /
• 1995

An electron gun system for the Pohang Light Source has been installed and operated successfully. The basic design parameters are acceleration voltage of 80 kV, maximum peak emission current of 5 A, minimum pulse width of 1 ns, and maximum repetition rate of 100 Hz. The gun has a triode structure and is composed of a cathode, a focusing electrode(Wehnelt), and an anode. To sustain a $5{\times}10^{-9}$Torr vacuum, a $230{\ell}/s$ Ion pump has been adopted. We adopted a control and monitoring system based on the fiber-optic technology. In this article, we present the structure and operation principle of the system with special interest on the nanosecond pulser, remote control and monitoring system.

• Journal of electromagnetic engineering and science
• /
• v.10 no.1
• /
• pp.6-12
• /
• 2010

In this paper, highly efficient class-F power amplifiers(PAs) with harmonic-controlling transmission lines(TLs) were built for cellular and WLAN applications at 840 MHz and 2.4 GHz each. Also, based on these single-band PAs, a dualband class-F PA was designed after a careful investigation into the harmonics of the two frequencies. The harmonic-controlling TL was designed for the class-F operation at dualband by switching the length of the shunt $\lambda$/4 TL part, while the series $\lambda$/4 TL is optimized for both frequencies. To verify the performance, two class-F PAs optimized at each frequency and a dualband class-F PA at the corresponding frequencies were built with the secondand the third-harmonic control circuits at each frequencies. As a result, the PA#1 at 840 MHz has a peak drain efficiency of 81.2 % with an output power of 24.4 dBm, while the PA#2 at 2.35 GHz shows a drain efficiency of 94.5 % with an output of 22.8 dBm. Finally, the dualband class-F PA#3 showed 60.5 % and 50.9 % drain efficiencies at 840 MHz and 2.4 GHz, with powers of 23.8 dBm and 19.62 dBm, respectively.

• ETRI Journal
• /
• v.38 no.4
• /
• pp.654-664
• /
• 2016

This paper presents a transformer-based reconfigurable synchronous boost converter. The lowest maximum power point tracking (MPPT)-input voltage and peak efficiency of the proposed boost converter, 20 mV and 88%, respectively, were achieved using a reconfigurable synchronous structure, static power loss minimization design, and efficiency boost mode change (EBMC) method. The proposed reconfigurable synchronous structure for high efficiency enables both a transformer-based self-startup mode (TSM) and an inductor-based MPPT mode (IMM) with a power PMOS switch instead of a diode. In addition, a static power loss minimization design, which was developed to reduce the leakage current of the native switch and quiescent current of the control blocks, enables a low input operation voltage. Furthermore, the proposed EBMC method is able to change the TSM into IMM with no additional time or energy loss. A prototype chip was implemented using a $0.18-{\mu}m$ CMOS process, and operates within an input voltage range of 9 mV to 1 V, and an output voltage range of 1 V to 3.3 V, and provides a maximum output power of 37 mW.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.41 no.3
• /
• pp.101-109
• /
• 2004

In this paper, we propose an efficient algerian for wavelet-based sti image coding method that utilizes the rate-distortion (R-D) theory. Since conventional tree-structured image coding schemes do not consider the rate-distortion theory properly, they show reduced coding performance. In this paper, we apply an rate-distortion optimized embedding (RDE) operation into the set partitioning in hierarchical trees (SPIHT) algorithm. In this algorithm, we use the rate-distortion slope as a criterion for the coding order of wavelet coefficients in SPIHT lists. We also describe modified set partitioning and rate-distortion optimized list scan methods. Experimental results demonstrate that the proposed method outperforms the SPIHT algorithm and the rate-distortion optimized embedding algerian with respect to the PSNR (peak signal-to-noise ratio) performance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.1
• /
• pp.16-20
• /
• 2020

In this study, a patterning method using self-aligned nanostructures was introduced to fabricate GaN-based fin-gate HEMTs with normally-off operation, as opposed to high-cost, low-productivity e-beam lithography. The honeycomb-shaped fin-gate channel width is approximately 40~50 nm, which is manufactured with a fine width using a proposed method to obtain sufficient fringing field effect. As a result, the threshold voltage of the fabricated device is 0.6 V, and the maximum normalized drain current and transconductance of Gm are 136.4 mA/mm and 99.4 mS/mm, respectively. The fabricated devices exhibit a smaller sub-threshold swing and higher Gm peak compared to conventional planar devices, due to the fin structure of the honeycomb channel.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.256-260
• /
• 2001

This paper presents boost and buck and buck-boost DC-DC converter circuit topologies of high-frequency soft switching transition PWM chopper type DC-DC high power converters with a single auxiliary passive resonant snubber. In the proposed boost power converter circuits operating under a principle of ZCS turn-on and ZVS turn-off commutation schemes, the capacitor and inductor in the auxiliary passive resonant circuit works as the loss less resonant snubber. In addition to this, the switching voltage and current peak stresses as well as EMI and RFI noises can be basically reduced by this single passive resonant snubber. Moreover, it is proved that converter circuit topologies with a passive resonant snubber are capable of solving some problems of the conventional hard switching PWM processing based on high-ferquency pulse modulation operation principle. The simulation results of this converter are discussed as compared with the experimental ones. The effectiveness of this power converter with a single passive resonant snubber is verified by the 5kW experimental breadboad set up.

• Journal of electromagnetic engineering and science
• /
• v.9 no.3
• /
• pp.152-158
• /
• 2009

We have developed a novel digital feedback predistortion(DFBPD) linearization based on RF feedback PD for the wide bandwidth modulated signals. The wideband PD operation is carried out by combining the DFBPD and memory lookup table(LUT). To experimentally demonstrate the linearization performance of the proposed PD technique for wideband signal, a class-AB amplifier using an LDMOSFET MRF6S23140 with 140-W peak envelope power is employed at 2.345 GHz. For a forward-link 2FA wideband code-division multiple-access signal with 10 MHz carrier spacing, the proposed DFBPD with memory LUT delivers the adjacent channel leakage ratio at an 10 MHz offset of -56.8 dBc, while those of the amplifier with and without DFBPD are -43.2 dBc and -41.9 dBc, respectively, at an average output power of 40 dBm. The experimental result shows that the new DFBPD with memory LUT provides a good linearization performance for the signal with wide bandwidth.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.3
• /
• pp.430-438
• /
• 1997

Deburring and edge finishing technology as the final process of machining operation is required for manufacturing of advanced precise conponents. But, deburring is considered as a difficult problem on going to the high efficient production and automation in the FMS. Removal of burr couldn't have a standard of its definition because of its various shapes, dimensions and properties and mostly depends on manual treatment. Especially, deburring for cross hole inside is very difficult owing to its shape passing through out perpendicular to a main hole. The electrochemical method is suggested as its solution in practical aspect. Therefore, electrochemical deburring technology needs to be developed for the high efficiency and automation of internal deburring in the cross hole. In this study, the new process in the eliminating burr inside cross hole, electrochemical deburring by the wheel electroplated with Cubic-Boron-Nitrade abrasives, is suggested. Its deburring mechanism is described and machining performances is investigated. Also, CBN electroplated wheel is designed and manufactured and then characteristics of electrochemical deburring are investigated through experiments. Overall electrochemical deburring performance against burr inside cross hole is examined in the various power sources such as peak current and direct current.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.720-725
• /
• 1991

In this thesis, the lead-lag compensator is designed to improve output characteristics of flyback zero voltage switching quasi-resonant converters. The switch and the diode are assumed ideally. And the SMPS is modelled by state equations with four operation modes. And the model for controller design is also achived by using a state space averaging method, which is continuous time average of state variables every period. The lag, the lead and the lead-lag compensator is designed the SMPS respectively. The time domain analysis and the frequency domain analysis are done for each compensated circuit. It is possible increasing the phase margin and improving the transient response by the compensators. The phase lag compensator has small overshoot comparatively. But the bandwidth is narrower than the others, so it has longest settling time. For the phase lead compensator, the response come to steady-state within short period. But the overshoot is the largest due to its large peak gain. Finally, the phase lead-lag compensator has medium characteristics in the overshoot and the settling time.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.2
• /
• pp.53-60
• /
• 2011

The available power generated from the FC power plant may not be sufficient to meet sustained load demand, peak demand or transient events. An supercapacitor bank(SCB) can supply a large burst of power, but it cannot store a significant amount of energy. The combined use of FC and SCB has the potential for the better energy efficiency, reducing the cost of FC technology and improved dynamic response. In this paper, A single PEMFC and PEMFC operated in parallel with a SC bank are presented, A new dynamic model of PEMFC system, the converter and controller has been developed for stand-alone applications. The simulation results are presented using Matlab/Simulink, and SimPowerSystems environments. It is confirmed that the results show a good performance and stable DC-link voltage for proposed dynamic and mathematical models developed for the combined FC/SCB.