• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.4
• /
• pp.1-9
• /
• 2002

The metallurgical reaction properties between the pad consisted of 0.5 $\mu\textrm{m}$Au/5 $\mu\textrm{m}$Ni/Cu layers on a conventional ball grid array (BGA) substrate and In-15 (wt.%)Pb-5Ag solder ball were characterized during the reflow process and solid aging. During the reflow process of 1 to 5 minutes, it was observed that thin $AuIn_2$ or Ni-In intermetallic layer was formed at the interface of solder/pad. The dissolution rate of the Au layer into the molten solder was about $2\times 10^{-3}$ $\mu\textrm{m}$/sec which is remarkably low in comparison with a eutectic Sn-37Pb solder. After solid aging treatment for 500 hrs at $130^{\circ}C$, the thickness of $Ni_{28}In_{72}$ intermetallic layer was increased to about 3 $\mu\textrm{m}$ in all the conditions nevertheless the initial reflow time was different. These result show that In atoms in the solder alloy were diffused through the $AuIn_2$ phase to react with underlaying Ni layer during solid aging treatment. From the microstructural observation and shear tests, the reaction properties between In-15Pb-5Ag alloy and Au/Ni surface finish were analyzed not to trigger Au-embrittlement in the solder joints unlike Sn-37Pb composition.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.3
• /
• pp.155-158
• /
• 2014

The phase transformation of Sn-Pb-Bi solder for photovoltaic ribbon during soldering was studied using real-time synchrotron x-ray scattering. At room temperature, Sn and Pb crystal phases in the solder existed separately. By heating to $92^{\circ}C$, a new PbBi alloy crystal phase was formed, which grew further up to $160^{\circ}C$. The Sn crystal phase first started to melt at $160^{\circ}C$, and was mostly melted at $165^{\circ}C$. In contrast, the Pb and PbBi crystal phases started to melt at $165^{\circ}C$, and were mostly melted at $170^{\circ}C$. The useful result was obtained, that the solder's melting temperature decreased from $183^{\circ}C$ to $170^{\circ}C$ by addition of a small amount of Bi atoms to the eutectic Sn62-Pb38 (wt%) solder. Our study first revealed the detailed in-situ phase transformation of Sn-Pb-Bi solder during heating to the eutectic temperature. Considering the results of peel strength and hardness, adding 1 wt% of Bi atoms to the Sn62-Pb38 (wt%) solder produced an appropriate composition.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.2
• /
• pp.187-192
• /
• 2011

UBM(Under Bump Metallurgy) is very important for successful realization of Flip-Chip technology. In this study, it is investigated the interfacial reactions between various Sn-Ag solder alloys and Ni-P/Au UBM and Cu plate finish. It is also evaluated the shear strength by using the micro shear-punch test method for Sn-37Pb alloy, binary and ternary alloys of environment-friendly Pb-free solder alloys which are applied in the electronic packages. In terms of interfacial microstructure, the Pb-free solder joints have thicker IMCs than the Sn-Pb solder joints. The thickness of IMC is related to Reflow time. The IMC has been observed to grow with the increase in Reflow time. As a result of the shear test, in case of Max. shear strength, Pb-free solder showed the highest strength value and Sn-37Pb showed the lowest strength value 10 be generally condition of Reflow time.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.4
• /
• pp.218-231
• /
• 2002

As the environmental regulation worldwide emerges, most notably in Europe and Japan, the elimination of Pb usage in electronic assemblies has been an important issue for microelectronics assembly due to the inherent toxicity of Pb. This has provided an impetus towards the development of Pb-free solders. A major factor affecting alloy selection is the melting point, since this will have a major impact on the other polymeric materials used in microelectronic assembly and encapsulation. Other important manufacturing issues are cost, availability, and wetting characteristics. Reliability related properties include mechanical strength, fatigue resistance, coefficient of thermal expansion and reactivity with substrate. In this article, Pb-free solder alloys have been proposed so far have been reviewed and are summarized.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.5
• /
• pp.332-337
• /
• 2015

We have studied the effects of Ag on the characteristics of $Sn_{60}Pb_{40}Ag_x$ (wt%) solder for photovoltaic ribbon. Ag atoms in the solder formed an alloy phase of $Ag_3Sn$ after reacting with some part of Sn atoms, while they did not react with Pb atoms, but decreased the mean size of Pb solid phase. The enhancement of peel strength between solar cell and ribbon is an important part in the developments of long-lifespan solar module. The peel strength of the solder ribbon of $Sn_{60}Pb_{40}$ (wt%) was $169N/mm^2$, and it was largely enhanced by adding a small amount of Ag atoms. The maximum peel strength was $295N/mm^2$ in the solder ribbon of $Sn_{60}Pb_{40}Ag_2$ (wt%). This result is caused by the high binding energy of 162.9 kJ/mol between Ag atoms in the solder and Ag atoms in Ag sheet.

• Journal of Powder Materials
• /
• v.6 no.1
• /
• pp.96-102
• /
• 1999

The effect of Pb addition on microstructure and wear resistance was studied in rapidly solidified Al-20Si-5Fe-xPb(x=2, 4, 6 wt.%) alloys. The R/S Al-20Si-5Fe-xPb (x=2, 4, 6 wt.%) alloys showed a fine and homogeneous microstructure and an improved wear property compared with Al-20Si-5Fe alloy, while no significant change in UTS (Ultimate Tensile Strength) was shown. Contribution of the dispersoids on the wear property was discussed by showing the plastic deformation layers formed during wear track.

• Nuclear Engineering and Technology
• /
• v.52 no.10
• /
• pp.2387-2393
• /
• 2020

In this study, a gradient material for shielding neutrons and gamma rays was developed, which consists of epoxy resin, boron carbide (B₄C), lead (Pb) and a little graphene oxide. It aims light weight and compact, which will be applied on the transportable nuclear reactor. The material is made up of sixteen layers, and the thickness and components of each layer were designed by genetic algorithm (GA) combined with Monte Carlo N Particle Transport (MCNP). In the experiment, the viscosities of the epoxy at different temperatures were tested, and the settlement regularity of Pb particles and B₄C particles in the epoxy was simulated by matlab software. The material was manufactured at 25 ℃, the Pb C and O elements of which were also tested, and the result was compared with the outcome of the simulation. Finally, the material's shielding performance was simulated by MCNP and compared with the uniformity material's. The result shows that the shielding performance of gradient material is more effective than that of the uniformity material, and the difference is most noticeable when the materials are 30 cm thick.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.2
• /
• pp.186-190
• /
• 2023

We studied the various characteristics of Sn-In (wt%) Pb-free solders for photovoltaic ribbon application. The solders near the eutectic composition of Sn₄₈In₅₂ (wt%) existed in InSn₄ and In₃Sn alloy phases, and in In crystal phase, but not in Sn crystal phase. In addition, the InSn₄ phase (γ-alloy) existed separately from the In₃Sn (β-alloy) and the In phase confirmed by an SEM-EDS-mapping. The melting temperature of the eutectic solder of Sn₄₈In₅₂ (wt%) was 119.2℃, and when the Sn content decreased in reference to the eutectic composition, it slightly increased to 121.4℃, but when the Sn content increased, it remained almost constant at 119.1℃. The peel strength of the ribbon plated with the Sn₄₂In₅₈ (wt%) solder was 38.7 N/mm², and it tended to increase when the Sn content increased. The peel strength of the eutectic Sn₄₈In₅₂ (wt%) solder was 53.6 N/mm², and that of the Sn₅₁In₄₉ (wt%) solder was 61.6 N/mm² that was the highest.

• Journal of the Korean Society for Heat Treatment
• /
• v.35 no.3
• /
• pp.130-138
• /
• 2022

In this study, the characteristic of an amorphous fishing weight material according to controlling the alloy type and alloy composition of the glass forming agent added in PbO₂ oxide was investigated. According to the experimental, when the glass forming agent of 15wt%SiO₂-1wt%MgO content was added in β-PbO₂, an amorphous fishing weight substitute having the lowest friction coefficient, excellent corrosion resistance and durability was obtained. The cell number of PbO₂-15wt%SiO₂-1wt%MgO sample incubated in cell culture fluid tended to hardly decrease even after a lapse of 24 hours, It means that the fabricated PbO₂-15wt%SiO₂-1wt%MgO sample is significantly less-toxic and harmless to the human body, unlikely to metallic lead. It is considered that an fabricated amorphous fishing weight substitute proved to have a potential as an eco-friendly material with little marine pollution.

• Journal of the Korean Chemical Society
• /
• v.15 no.2
• /
• pp.49-54
• /
• 1971

It is shown that the impurities of Cu(II), Pb(II), Zn(II) and Ag(I) in Bismuth metal and the components of Pb(II), Zn(II) and Sn(IV) in Bismuth alloy are separated into their components from each other by elutions through $3.14cm^2{\times}10cm$ cation exchange resin, $Dowex\;50w\;{\times}\;8$ (100~200 mesh), column with the mixed solutions of HAc and NaAc as the eluents. The elution curve of Fe(III) has a long tailing and is not separated quantitatively from Bi(III). The eluents used for this separation are as follows; 1M HAc + 0.1M NaAc (pH 3.36) for Fe(III) and Bi (III). 0.3M HAc + 0.3M NaAc (pH 4.70) for Cu(II), Pb(II) and Zn(II). 0.5M HAc + 0.5M NaAc (pH4.70) for Ag(I) and Sn(IV). The analysis of cations eluted are carried out by spectrophotometry and EDTA titrimetry. Their recoveries are more than 99%.