• International Journal of Highway Engineering
• /
• v.15 no.1
• /
• pp.23-36
• /
• 2013

PURPOSES: The problem under this circumstance is that the erosion not only drops strength of the steel dowel bar but also comes with volume expansion of the steel dowel bar which can reduce load transferring efficiency of the steel dowel bar. To avoid this erosion problem, alternative dowers bars are developed. METHODS: In this study, the bearing stresses between the FRP tube dowel bar and concrete slab are calculated and compared with its allowable bearing stress to check its structural stability in the concrete pavement. These comparisons are conducted with several cross-sections of FRP tube dowel bars. Comprehensive laboratory tests including the shear load-deflection test on a full-scale specimen and the full-scale accelerated joint concrete pavement test are conducted and the results were compared with those from the steel dowel bar. RESULTS: In all cross-sections of FRP tube dowel bars, computed bearing stresses between the FRP tube dowel bar and concrete slab are less than their allowable stress levels. The pultrusion FRP-tube dowel bar show better performance on direct shear tests on full-scale specimen and static compression tests at full-scale concrete pavement joints than prepreg and filament-winding FRP-tube dowel bar. CONCLUSIONS: The FRP tube dowel bars as alternative dowel bar are invulnerable to erosion that may be caused by moisture from masonry joint or bottom of the pavement system. Also, the pultrusion FRP-tube dowel bar performed very well on the laboratory evaluation.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.95-105
• /
• 2009

This study was conducted to investigate the effects of concrete flexural strength and surface smoothness, which were pay factors of concrete pavements, on pavement performance, and to develop the methodologies to determine the proper allowable ranges according to the magnitudes of those pay factors. The concrete flexural strength was analyzed using the AASHTO, power, and linear fatigue failure models, and the surface smoothness was analyzed for the roughness indices of PSI, IRI, and PrI using the AASHTO model. The analysis results showed that the allowable range of the flexural strength should be determined using the rate between the deficiency and strength, and the penalty should be linearly proportional to the strength deficiency rate because the linear relationship between the strength deficiency rate and the reduction in pavement life was observed. As the initial surface smoothness became better, the smoothness deficiency rate should be larger. The penalty due to the surface smoothness deficiency should also be linearly proportional to the smoothness deficiency rate.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.87-94
• /
• 2009

Volume of concrete slab changes by variations of temperature and moisture after its placement. Shrinkage due to evaporation causes tensile stress in the slab when contraction of the slab is restrained by its self weight, friction with subbase, and etc. Actual tensile stress caused by the shrinkage was less than theoretically predicted stress according to previous studies. It was the stress reduction due to visco-elastic property of the early-age concrete slab partially restrained. In this study, strains of restrained circumferential, unrestrained circumferential, and unrestrained square pillar concrete specimens were measured to investigate stress reduction of the specimens with age of concrete. Elastic modulus of the concrete was measured at the age of 1, 3, 7, 14, 28 days and penetration test was performed. The stress reduction was calculated by input the test results into theoretical equations suggested by previous researchers. The stress reduction of the restrained concrete specimens will be applied to design of concrete pavements based on results of the study.

• International Journal of Highway Engineering
• /
• v.9 no.3
• /
• pp.51-62
• /
• 2007

Recently various low-noise-pavement methods have been developed. Since tire/pavement noise is the major source of traffic noise at high speed condition, the core-technology of low-noise pavement is to produce the road surface texture that can reduce tire/pavement noise. The difficulties in the development of the low-noise pavements are high costs and time to construct test roads, since vehicles have to travel on the test roads to evaluate the noise from a particular condition of pavement surface. Tire/Pavement Noise Simulator were developed to overcome those difficulties and the reliability of developed Tire/Pavement Noise Simulator are investigated based on the simulating and measuring the noise of tire-tined concrete pavement and tire-non tined concrete pavement.

• International Journal of Highway Engineering
• /
• v.9 no.3
• /
• pp.135-143
• /
• 2007

The pavement system constructed by tieing a number of precast concrete slabs employing prestressing techniques is called the precast prestressed concrete pavement. The behavior of this type of pavement system under post-tensioning was analyzed using a finite element model. First, the optimal number of anchors was determined by investigating the distribution of compressive stresses in the pavement system due to post-tensioning. Then, the effects of the parameters such as the horizontal resistance of underlying layers, the pavement length, the slab thickness, and the bearing area of the anchorage on the distribution of compressive stresses were analyzed. The horizontal resistance of underlying layers induced the loss of compressive stresses, and the loss increased in the middle of the pavement. As the pavement length increased or the slab thickness decreased, the stress loss due to the horizontal resistance of underlying layers became larger. However, the bearing area of the anchorage where the compressive forces were applied did not much affect the distribution of compressive stresses.

• International Journal of Highway Engineering
• /
• v.9 no.4
• /
• pp.135-147
• /
• 2007

Segregation in asphalt pavements occurs as a result of the non-uniform distribution of coarse and fine aggregates and causes premature distresses, such as cracking, raveling, and stripping. The effect of segregation on rutting, however, has not been clearly identified. Experimental and analytical work performed in this study indicates that rutting performance is affected by segregation of mixtures. However, the aggregate structure of mixtures appears to be a more critical factor that determines the rutting performance, rather than the level of segregation. Based on the field mixtures evaluated, an increase of coarse aggregate volume in an asphalt mixture is an important factor that results in good rutting performance. This effect holds true for mixtures with lower levels of air voids, but for mixtures with higher levels of air voids, the air voids effect becomes dominant, resulting in a reduction in rutting performance. An air void content of 10% appears to be a threshold that determines the rutting performance of Superpave mixtures. Once the air void content exceeds 10%, the rutting performance of Superpave mixtures decreases significantly, despite the coarse aggregate volume.

• International Journal of Highway Engineering
• /
• v.15 no.5
• /
• pp.91-99
• /
• 2013

PURPOSES : This study aims at proposing the methodology for benefit evaluations in pavement maintenance methods and timings using KoPMS(Korean Pavement Management System) software which was developed for efficient pavement management. METHODS : This study classified pavement sections into 4 clusters considering AADT(Annual Average Daily Traffic) and ESAL(Equivalent Single-Axle Load) using cluster analysis and used the deterioration models in each cluster. Increased user costs due to pavement deterioration as time goes by and agent costs for maintenance were estimated. Based on deterioration model and KoPMS software, Methodology for benefit evaluation was proposed in pavement maintenance methods and with/without implementation using real pavement section data. RESULTS : This study verified that considering agent costs only would be constrained to decide pavement maintenance methods and timings, and ascertained that decision making with agent and user costs would be effective. In addition, this study revealed that pavement maintenance methods and timings can be affected by AADT and ESAL and frequent pavement maintenances can be more efficient for benefits in pavement sections with more AADT and ESAL. Also this study found that user costs would be more affected to decision making than agent costs. Moreover, Delay of conducting pavement maintenance caused increased vehicle operating costs and environmental costs because of poor conditions of pavements. CONCLUSIONS : This study proposed LCCA and benefit estimation methodology of pavement with considering agent and user costs. The results of this study can be used for baseline data of efficient pavement asset management.

• International Journal of Highway Engineering
• /
• v.18 no.2
• /
• pp.37-42
• /
• 2016

PURPOSES : The objective of this study is to determine the optimal frequency of ground penetrating radar (GPR) testing for detecting the voids under the pavement. METHODS : In order to determine the optimal frequency of GPR testing for void detection, a full-scale test section was constructed to simulate the actual size of voids under the pavement. Voids of various sizes were created by inserting styrofoam at varying depths under the pavement. Subsequently, 250-, 500-, and 800-MHz ground-coupled GPR testing was conducted in the test section and the resulting GPR signals were recorded. The change in the amplitude of these signals was evaluated by varying the GPR frequency, void size, and void depth. The optimum frequency was determined from the amplitude of the signals. RESULTS: The capacity of GPR to detect voids under the pavement was evaluated by using three different ground-coupled GPR frequencies. In the case of the B-scan GPR data, a parabolic shape occurred in the vicinity of the voids. The maximum GPR amplitude in the A-scan data was used to quantitatively determine the void-detection capacity. CONCLUSIONS: The 250-MHz GPR testing enabled the detection of 10 out of 12 simulated voids, whereas the 500-MHz testing allowed the detection of only five. Furthermore, the amplitude of GPR detection associated with 250-MHz testing is significantly higher than that of 500-MHz testing. This indicates that 250-MHz GPR testing is well-suited for the detection of voids located at depths ranging from 0.5~2.0 m. Testing at frequencies lower than 250 MHz is recommended for void detection at depths greater than 2 m.

• Journal of Korea Water Resources Association
• /
• v.38 no.6 s.155
• /
• pp.449-460
• /
• 2005

In this study, a WEP (Water and Energy transfer Processes) model was used to simulate the water cycle of the Dorimcheon catchment which suffers from the distorted water cycle as a typical urban catchment. Two different land uses in the past (i.e. 1975) and at present (i.e. 2000) were incorporated into the simulation to investigate the runoff characteristics resulting from the increase of the impervious ratio due to urbanization. The simulation results show that the concentration time is decreased and the peak discharge and the total runoff are increased by urbanization while the infiltration and baseflow are reduced. In addition, the effects of infiltration trenches and permeable pavements were also simulated to search for alternatives that can restore the distorted water cycle. The simulation results prove that the installation of both alternatives can restore the runoff characteristics to that prior to urbanization.

• Geomechanics and Engineering
• /
• v.1 no.4
• /
• pp.323-335
• /
• 2009

Gravels forming part of the base of flexible pavements experience abrasion and crushing as a result of static and dynamic loads. Abrasion takes place when the sharp corners of the particles of gravel are removed as a result of compressive and shear loads. As a result of abrasion, the particles change in shape. Crushing is caused by the fragmentation of the particles into a mixture of many small particles of varying sizes. In this study, the abrasion and crushing of gravels are evaluated experimentally and analytically. The laboratory component of this study involves gravels that were subjected to abrasion and dynamic compression tests. The evaluation of the abrasion and crushing experienced by the gravel was carried out using fractals. In this study, the fractal dimension concept from fractal theory is used to evaluate: (a) the changes in shape, and (b) the crushing (fragmentation) of the original particles of gravel. It was determined that the fractal dimension of the profile of the particles decreased as a result of abrasion. With respect to crushing, the fragmentation fractal dimension was found to increase with the degree of breakage of the gravel. To understand the influence of crushing on the permeability of the gravels, the hydraulic conductivity of the gravels was measured before and after crushing. The hydraulic conductivity of the gravels was found to decrease with an increase in their level of crushing. Also, changes in the angle of friction of the granular materials as a result of abrasion was calculated using the Krumbein's roundness chart. The angle of friction of the granular materials was found to decrease as a result of abrasion.