• Composites Research
• /
• v.29 no.6
• /
• pp.408-413
• /
• 2016

Commonly-used polymers are manufactured as versatile forms. Furthermore, continuous polymer fibers are recently manufactured using nylon or aramid fiber. One of common epoxy was also used to make polymer fibers. Bisphenol-A type was used as base epoxy whereas amine and anhydride were used as hardeners. Epoxy fibers was cured by stepping up the temperature to maintain the shape of epoxy fiber. Surface energy was measured to confirm the degree of interfacial adhesion by modified static contact angle method. After mechanical properties were measured via fiber tensile test, the evaluation of fiber fracture was proceeded. Tensile strength of epoxy fiber using amine type hardener was higher as 138 MPa than anhydride case as 70 MPa. Fractured surface exhibited different failure patterns at the cross-section.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.3
• /
• pp.17-26
• /
• 2010

Pb-Sn solder is rapidly being replaced by lead-free solder for board-level interconnection in microelectronic package assemblies due to the environmental protection requirement. There is a general lack of mechanical reliability information available on the lead-free solder. In this study, thermo-mechanical behaviors of wire-bond plastic ball grid array (WB-PBGA) package assemblies are characterized by high-sensitivity moire interferometry. Experiments are conducted for two types of WB-PBGA packages that have Pb-Sn solder and lead-free solder as joint interconnections. Using real-time moire setup, fringe patterns are recorded and analyzed for several temperatures. Bending deformations of the assemblies and average strains of the solder balls are investigated and compared for the two type of WB-PBGA package assemblies. Results show that shear strain in #3 solder ball located near the chip shadow boundary is dominant for the failure of the package with Pb-Sn solder, while normal strain in #7 most outer solder ball is dominant for that with lead-free solder. It is also shown that the package with lead-free solder has much larger bending deformation and 10% larger maximum effective strain than the package with Pb-Sn solder at same temperature level.

• Journal of Gifted/Talented Education
• /
• v.20 no.2
• /
• pp.527-546
• /
• 2010

As research results, male schoolchildren were found to solve problems more easily in the area of basic process skills while female schoolchildren were found to solve problems in the area of integrated process skills. Schoolboys showed the high tendency to solve problems in a planning pattern by memory, or solving pattern in which they are fully aware of the contents of both questions and choices in answer sheets, or the pattern which they are fully aware of distracters in answer sheets; in contrast, schoolgirls showed a high tendency to get a good result by analyzing both questions & choices in answer sheets or analyzing a chart, graph and illustration, which explains that female schoolchildren tend to solve problems in more diverse ways than male schoolchildren. In case of a poor achiever, male schoolchildren tend to make a failure while trying to find answers in an inadequately understood state or trying to solve on mistaken memories while doing questions immediately while female schoolchildren showed a lot of solving patterns based on mistaken memories or wrong analyses of a chart, illustration, or graph. Such results are believed to offer the implications on the understanding of male/female schoolchildren in their problem-solving pattern of their exploratory ability in elementary science and on its subsequent program development.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.1 s.53
• /
• pp.195-204
• /
• 2009

Application of steel plates is one of widely used methods for shear strengthening of reinforced concrete beams that are insufficient of shear capacity. While the existing method applying solid steel plates provides good shear rigidity, however, it is concerned by brittle bond failure patterns, inefficient material usage, and low constructability. The use of strap type steel plates has also shortcomings of low strenthening effect due to small interface bonding area and ununified behavior between plates and main body. Therefore, this study aims to introduce the shear strengthening method using slit type steel plate, which can solve out the problems aforementioned, and to verify its strengthening effects on shear capacity. A total of 13 specimens strengthened by slit type steel plates were fabricated with primary test parameters of plate width, slit spacing, and plate thickness. The test results from this study were also compared to those from the existing research on RC beams strengthened by strap type steel plates, and the strengthening effects on shear capacity of specimens having bonded slit type steel plates were quantitatively analyzed. The test results showed that the RC beams strengthened by slit type steel plates had greater shear capacities than those with strap type steel plates, which is considered to be the effects of improved composite behavior and larger interface bonding area in the RC beams strengthened by the slit type steel plates.

• Radiation Oncology Journal
• /
• v.6 no.2
• /
• pp.195-201
• /
• 1988

Sixty patients with proven lung cancer were retrospectively studied to determine whether postoperative radiation therapy improves survival. Patterns of treatment failure and 5 year survival were assessed according to extent of tumor spread, histology, type of operation, positive resection margin and radiation dose. Of the 60 patients, excluding S patients who received incomplete treatment or poor pulmonary function,55 patients received postoperative radiation therapy following curative resection. The overall survival at 5 years was $39\%$. The hilar and mediastinal lymph node involvement had an influence on survival. The authors recommend that patients with resection. lung cancer involving the hilar and mediastinal lymph nodes may require postoperative radiotherapy to reduce the local recurrence and improve survival.

• Magazine of the Korea Concrete Institute
• /
• v.3 no.2
• /
• pp.123-132
• /
• 1991

The purpose of this study was to Investigate the effects of bent - up bar Within beam - column 1lint core with High - Strength Concrete up to 800kg/$cm^2$. To achieve these objectives, 5 specimens were designed and tested under monotoric loading and reversed cyclic loadings. The primary variables were the number of bent-up bars, compressive strength of concrete and loading patterns. The results showed that the load capacity of specimen subjected to monotonic loading had more large than that of specirnn subjected to reversed cyclic loadings and the bent - up bar within joint core could prevented the crack at the joint face from propagating into the pint core but the failure was concentrated at the face of beam - column pint. Thus the study on flexural strength ratio should be accomplished before using bent - up bars within the joint core.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.3
• /
• pp.80-86
• /
• 2020

In the fabrication process of inverted multi-tee (IMT) slabs, concrete has to be poured twice due to its shape, which is a huge disadvantage as a precast member. To overcome this, a new technique for manufacturing IMT slabs using a slipform method has been recently developed. In this study, flexural and shear tests were carried out to investigate the structural performances of inverted multi-tee (IMT) slabs manufactured using slipform method. To this end, one flexural specimen and two shear specimens with topping concrete were fabricated, and their failure modes and crack patterns, and the slips that occurred between the precast slab and topping concrete were measured and analyzed in detail. In addition, the flexural and shear strengths of the specimens were evaluated by utilizing the structural design code, and a shear strength estimation method, which is suitable for composite IMT slabs with different concrete properties, was proposed for practical design. The IMT slab satisfied the nominal flexural strength calculated by the current design code, and the proposed method provided a good estimation of the shear strength of the specimens.

• Korean Journal of Clinical Laboratory Science
• /
• v.48 no.1
• /
• pp.22-29
• /
• 2016

Serum gamma-glutamyltransferase (GGT) has been widely used as a marker of alcohol intake and liver failure. Recently, the relativity between GGT and various diseases has been identified with growing interest. In this study, we examined relativity between GGT value and risk factors of coronary heart diseases among those with normal GGT value, excluding heavy drinkers. Specifically, we compared the differences based on age and gender. Data from the 2011 KNHNES were used (N=3,619). When the subjects were categorized according to quartile based on the serum GGT levels, there was 10~20, 21~27, 28~38, 39~71 IU/L in men, and 6~12, 13~16, 17~22, 23~42 IU/L in women. The mean of most variables was the highest in the $4^{th}$ quartile (Q4), however age and LDL Cholesterol were the highest in the $2^{nd}$ quartile (Q2) in men. The FRS and 10-year CHD risk was the highest in the $2^{nd}$ quartile in men, and the highest in the $4^{th}$ quartile in women. Increased GGT was correspondingly linked with age in women but age was the highest in GGT in the $2^{nd}$ quartile in men. In the 70's, the highest Q1 and Q2 was in men and the highest Q3 and Q4 in women. Although GGT value was within the normal range, increased GGT showed correlation with various risk factors. The FRS and 10-year CHD risk showed different patterns according to age and gender along with increased GGT value.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.5
• /
• pp.65-78
• /
• 2008

In case of cut-slopes or shallow-depth tunnels, sliding along with discontinuities or rotation could play a critical role in judging stability. Although numerical analysis is widely used to check the stability of these cut-slopes and shallow-depth tunnels in early design process, common analysis programs are based on continuum model. Performing continuum model analysis regarding discontinuities is possible by reducing overall strength of jointed rock mass. It is also possible by applying ubiquitous joint model to Mohr-Coulomb failure criteria. In numerical analysis of cut-slope, main geotechnical properties such as cohesion, friction angle and elastic modulus can be evaluated by empirical equations. This study tried to compare two main systems, RMR and GSI system by applying them to in-situ hazardous cut-slopes. In addition, this study applied ubiquitous joint model to simulation model with inputs derived by RMR and GSI system to compare with displacements obtained by in-situ monitoring. To sum up, numerical analysis mixed with GSI inputs and ubiquitous joint model proved to provide most reliable results which were similar to actual displacements and their patterns.

• Radiation Oncology Journal
• /
• v.22 no.1
• /
• pp.11-16
• /
• 2004

Purpose: To evaluate the survival rate, local failure rate and patterns of failure, and analyze the prognostic factors affecting local relapse of ductal carcinoma in situ treated with breast conserving surgery and radiotherapy Materials and Methods: From June 1995 to December 2001, 96 patients with ductal carcinoma in situ treated with breast conserving surgery and radiotherapy were retrospectively analyzed. The operations were either local or wide excision in all patients, with an axillary lymph node dissection performed in some patients. Radiation dose to the whole breast was 50.4 Gy, over 5 weeks, with 1.8 Gy daily fractions, with additional doses ($10\~14$ Gy) administered to the primary tumor bed in some patients with close ($\leq$2 mm) or positive resection margin. The median follow-up period was 43 months (range $10\~102$ months). Results: The 5-year local relapse free survival and overall survival rates were 91 and $100\%$ respectively. Local relapse occurred in 6 patients ($6.3\%$). Of the 6 recurrences, one was invasive ductal cell carcinoma. With the exception of one, all patients recurred 2 years after surgery. There was no regional recurrence or distant metastasis. Five patients with local recurrence were salvaged with total mastectomy, and are alive with no evidence of disease. One patient with recurrent invasive ductal cell carcinoma will receive salvage treatment. On analysis of the prognostic factors affecting local relapse, none of the factors among the age, status of resection margin, comedo type and nuclear grade affected local relapse. Operation extent also did not affect local control (p=0.30). In the patients with close resection margin, boost irradiation to the primary tumor bed did not affect local control (p=1.0). Conclusions: The survival rate and local control of the patients with ductal carcinoma in situ treated with breast conserving surgery and radiotherapy were excellent. Close resection margin and boost irradiation to the primary tumor bed did not affect local relapse, but further follow-up with much more patients is needed.