• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.516-521
• /
• 2002

A study was carried out to grow an understanding of the microstructural development of friction stir welds on an AZ91D magnesium alloy, and to evaluate the mechanical properties of the welds. AZ91D plates with the thickness of 4mm were used, and the microstructural development of the weld zone was investigated using optical and scanning electron microscopes. Square butt welding joint with good quality was obtained at the conditions of under 187mm/min of travel speed with 1100 to 1250 rpm of tool rotation speed. The microstructure within the weld region consisted of fine equiaxed grains with no evidence of the original dendritic structure. The hardness tests showed slightly increased harness in the weld region, and the minimum hardness measured is in that of the parent material. Tensile strength of the weld zone was remarkably improved due to very fine recrystallized structure. XRD pattern of weld zone revealed the removal of $\beta$ intermetallic compounds, $Mg_{17}$Al$_{12}$, which had been distributed in the base metal.l.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.1
• /
• pp.97-102
• /
• 2013

Objective: The aim of this study was to develop an automated computer-aided diagnostic system for diagnosis of thyroid cancer pattern in fine needle aspiration cytology (FNAC) microscopic images with high degree of sensitivity and specificity using statistical texture features and a Support Vector Machine classifier (SVM). Materials and Methods: A training set of 40 benign and 40 malignant FNAC images and a testing set of 10 benign and 20 malignant FNAC images were used to perform the diagnosis of thyroid cancer. Initially, segmentation of region of interest (ROI) was performed by region-based morphology segmentation. The developed diagnostic system utilized statistical texture features derived from the segmented images using a Gabor filter bank at various wavelengths and angles. Finally, the SVM was used as a machine learning algorithm to identify benign and malignant states of thyroid nodules. Results: The SVMachieved a diagnostic accuracy of 96.7% with sensitivity and specificity of 95% and 100%, respectively, at a wavelength of 4 and an angle of 45. Conclusion: The results show that the diagnosis of thyroid cancer in FNAC images can be effectively performed using statistical texture information derived with Gabor filters in association with an SVM.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.1
• /
• pp.49-58
• /
• 2017

Due to low annual average temperature, road tunnel lining in domestic cold region (Gangwon province) experiences durability problems. The financial and human damage due to cracks, breakout, exfoliation and water leakage increases every year. However, domestic research on effect of temperature on road tunnel lining damage is insufficient. Thus, this research has investigated 70 tunnels located in cold region (Gangwon-do) to analyze damage status. Furthermore, by contrasting damage on tunnels in relatively warm Gangneung area with those in relatively cold Hongcheon area, the effect of temperature on road tunnel lining damage was analyzed.

• The KSFM Journal of Fluid Machinery
• /
• v.3 no.4 s.9
• /
• pp.22-29
• /
• 2000

Numerical analysis using three dimensional finite volume method for the discretization, adaptive grid method for the numerical accuracy, multiple rotating frame method for the rotating body and the standard $k-{\epsilon}$ model for the turbulent flow was performed to understand the heat transfer phenomena and to improve the efficiency of the scroll compressor. The temperature measurement was carried out under ARI condition. It was found that the fluid temperature in the compressor was predicted accurately while the temperature of the motor coil showed large discrepancy between the calculation and experiment due to the large anisotropy of the conductivity and non homogeneity. We found that the efficiency of the compressor depends on the inlet temperature of the compressing part and the flow pattern around the inlet region of the compressing part influences the inlet temperature due to high surface temperature of the main frame. The efficiency of the compressor using Coanda effect is higher than the previous one because the smooth suction at the inlet region of the compressing part leads to low heat transfer to the refrigerant of the compressor.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.2
• /
• pp.69-73
• /
• 2008

This article shows that the susceptibility of the device pattern to thermal stress-induced damage has a strong dependence on its proximity to the device comer in semiconductor devices utilizing lead-on-chip (LOC) die attach technique. The result, as explained based on numerical calculation and experiment, indicateds that the stress-driven damage potential of the passivation layer is the highest at the device comer. Thus, the bonding pads, which are very susceptible to passivation damage, should be designed to be located along the central region rather than the peripheral region of the device.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.14-21
• /
• 2001

An experimental study has been conducted to investigate the heat/mass transfer characteristics within a square film cooling hole with asymmetric inlet flow conditions. The asymmetric inlet flow condition is achieved by making distances between side walls of secondary flow duct and film cooling hole different; one side wall is $2D_h$ apart from the center of film cooling hole, while the other side wall is $1.5D_h$ apart from the center of film cooling hole. The heat/mass transfer experiments for this study have been performed using a naphthalene sublimation method and the flow field has been analyzed by numerical calculation using a commercial code. Swirl flow is generated at the inlet region and the heat/mass transfer pattern with the asymmetric inlet flow condition is changed significantly from that with the symmetric condition. At the exit region, the effect of mainstream on the inside hole flow is reduced with asymmetric condition. The average heat/mass transfer coefficient is higher than that with the symmetric condition due to the swirl flow generated by the asymmetric inlet condition.

• Journal of Mechanical Science and Technology
• /
• v.18 no.2
• /
• pp.313-324
• /
• 2004

A rich phenomenon in the dynamics of azimuthal vortices in a circular cylinder caused by the inertial oscillation is investigated numerically at high Reynolds numbers and moderate Rossby numbers. In the actual spin-up flow where both the Ekman circulation and the bottom friction effects are included, the first appearance of a seed vortex is generated by the Ekman boundary-layer on the bottom wall and the subsequent roll-up near the corner bounded by the side wall. The existence of the small vortex then rapidly propagates toward the inviscid region and induces a complicated pattern in the distribution of azimuthal vorticity, i.e. inertial oscillation. The inertial oscillation however does not deteriorate the classical Ekman-pumping model in the time scale larger than that of the oscillatory motion. Motions of single vortex and a pair of vortices are further investigated under a slip boundary-condition on the solid walls. For the case of single vortex, repeated change of the vorticity sign is observed together with typical propagation of inertial waves. For the case of a pair of vortices with a two-step profile in the initial azimuthal velocity, the vortices' movement toward the outer region is resisted by the crescent-shape vortices surrounding the pair. After touching the border between the core and outer regions, the pair vortices weaken very fast.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.11
• /
• pp.3706-3713
• /
• 1996

A numerical study on natural convection induced by free surface heat flux and cold left and hot right walls in glass melting furnaces has been performed. A function of heat flux derived from the combustion environments of actual glass melting furnace is applied to thermal boundary condition at free surface. Fundamentally there exist two flow cells in cavity (left counterclockwise one and right clockwise one). The effects of heat flux and Rayleigh number are investigated through two-dimensional steady-state assumption. The convection strength of two flow cell located in left region continuously increases. In the mean time the strength of flow cell in right region increases and then decreases. Critical Rayleigh number in which two flow cells take place above and below show linear dependence on the free surface heat flux. To maintain the traditional flow pattern (left and right flow cells) in glass melting furnace, Rayleigh number is recommended to be below 10$^{5}$ .

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.8
• /
• pp.3125-3130
• /
• 2015

Background: Breast cancer is a common cancer affecting women in Malaysia and the use of complementary/alternative medicine (CAM) has been associated with delays in getting treatment. The aim of the study was to explore the use of CAM and the influencing factors in the Northern region of Peninsular Malaysia. Materials and Methods: This was a cross-sectional descriptive study on a convenience sample of 100 Malaysian breast cancer survivors. Findings: The reported use of CAM among the breast cancer survivors was lower than in other studies but the types of CAM used had a similar pattern with nutrition supplements/vitamins being the most common. The factors that positively influenced the use of complimentary/traditional therapy were income and getting information from television or radio. Survivors with access to internet/blogs appear to have lower odds of using complimentary/traditional therapy compared to the respondents who reported no such access. Conclusions: Information transmitted via television and radio appears to have a positive influence on CAM use by breast cancer patients compared to other information sources and it is important to ensure that such information is accurate and impartial.

• Asian Pacific Journal of Cancer Prevention
• /
• v.13 no.3
• /
• pp.975-978
• /
• 2012

P63 is a gene product required in cell cycle regulation which plays vital roles in tumor differentiation. Aims of the present study were to assess the frequency, pattern, sensitivity and specificity of two p63 protein clones P63 4A4 and P63 4A4+Y4A3 in squamous cell carcinomas (SCCs). Thirty cases of head and neck region SCC diagnosed on the basis of H&E staining were examined along with 60 cases of head and neck region biopsies other than squamous cell carcinoma, negative on H&E staining, were taken as control. Immunostaining was performed on slides according to the Thermo Scientific UltraVision LP detection System. P63 4A4+Y4A3 clone is more sensitive 96.6% in comparison to 86% in P63 4A4 with having greater NPV of 98.3%. The results signify the importance of P63 4A4+Y4A3 marker over the old markers and may be used as a confirmatory marker of squamous cell carcinoma.