• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.624-630
• /
• 1997

Zeolite A helps an increase of detergency performance according to showing the ion exchange effect for polyvalant ions and it's detergency performance could be calculated quantitatively by using the disperse stabilization theory because it is water-insoluble material and is as colloid particles in aqueous solution. In this study, zeta potential of carbon black, cellulose, and Zeolite A were measured in each inorganic salt solutions and applied to the theory of Heterocoagulation in order to evaluate the detergency performance of Zeolite A about the particulate soil at the view point of interaction potential energy. Zeolite A was shown help an increase of detergency performance according to the increasing of the steric repulsion between Zeolite A and cellulose in $Na2CO_3$ solution and the decrease of re-deposition of carbon black on the fabric by rapid coagulation with carbon black in $Na_2SO_4$ solution.

• Journal of Environmental Science International
• /
• v.12 no.2
• /
• pp.217-225
• /
• 2003

Samples of size-fractionated PM10 (airborne particulate matter with aerodynamic diameter less than $10\mu\textrm{m}$) were collected at an urban site in Jeju city from May to September 2002. The mass concentration and chemical composition of the samples were measured. The data sets were then applied to the CMB receptor model to estimate the source contribution of PM10 in Jeju area. The average PM10 mass concentration was 28.80$\mu\textrm{g}/m^3$ ($24.6~33.49\mu\textrm{g}/m^3$), and the FP (fine particle with aerodynamic diameter less than $2.l\mu\textrm{m}$ fraction in PM10 was approximately 8% higher than the CP (coarse particle with aerodynamic diameter greater than $2.l\mu\textrm{m}$ and less than $10\mu\textrm{m}$ fraction in PM10. The CP composition was obviously different from the FP composition, that is, the most abundant water soluble species was nitrate ion in the FP, but sulfate ion in the CP. Also sulfur was the most dominant element in the FP, however, sodium was that in the CP. From CMB receptor model results, it was found that road dust was the largest contributor to the CP mass concentration (45% of the CP) and ammonium nitrate, domestic boiler, and marine aerosol were major sources to the CP mass. However, the secondary aerosol was the most significant contributor to the FP mass concentration (45% of the FP). In this study, it was suggested that the contributions of soil dust and gasoline vehicle became very low due to collinearity with road dust and diesel vehicle, respectively.

• Economic and Environmental Geology
• /
• v.27 no.5
• /
• pp.469-477
• /
• 1994

Many researchers have investigated most representative sequential extraction method using various reagents for determining the chemical forms of metals in soils and sediments. In this paper, a newly modified method for sequential extraction scheme based on Tessier's method by Environmental Geochemistry Research, Centre for Environmental Technology, Imperial College, was introduced and examined. In comparison with Tessier's method, originally designed for sediment analysis by Atomic Absorption Spectrophotometry (AAS), the sequential extraction scheme has been developed for the multi-element analysis by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES). The partitioning of particulate trace elements was classified into five fractions: (i) exchangeable, (ii) bound to carbonates or specially adsorbed, (iii) bound to Fe and Mn oxides, (iv) bound to organic matter and sulphides and (v) residuals. The experimental results of the pilot study for in-house reference material (HRM2) and certified international standard reference material (SRM2711) using the modified method showed not only reasonable precision and accuracy but also acceptable overall recovery rates. In addition, mine dump soils sampled in the Dalsung Cu-W mine, Korea were prepared and sequentially extracted using the method. Most of Cu was bound to organic matter/sulphides and residual fractions. The dominant fraction of soil Pb and Zn in the study area was found in the residuals. The fraction of Cd showed a wide variation between samples and could be found bound to the carbonates or specially adsorbed, oxides, organic fraction and residuals. The recovery rates of Cd, however, were poor due to relatively low Cd concentrations in soils. The heavy metals in these mine dumps appear to be in the more inert forms and should not be readily bioavailable. The soils, however, had very low pH values (average 4.1) and had sandy textures; consequently, rapid infiltration of rainfall may increase leaching of Zn and Cd which were found to be around 5 to 10% of the exchangeable fraction. As a result of the investigation of this study, it has been strongly recommended that these mine waste materials should still be considered a significant contaminant source and will need environmental remediation to prevent pollutants from being released into the environment.

• Economic and Environmental Geology
• /
• v.30 no.4
• /
• pp.341-352
• /
• 1997

Retention ponds have been dug along some of the motorways in France to minimize environmental pollution by keeping pollutants from spreading over the surrounding area. In order to study heavy metal pollution and diagenetic behaviour of sediments, eight core samples were collected from the bottom of a retention pond located along the A-71 motorway in Sologne. The metal concentrations in interstitial waters and extractable metal concentrations in sediment layers using sequential chemical extraction method were determined. The depth distributions of Pb, Zn and Cd concentrations in interstitial water and particulate sediments were studied, and distribution coefficients (KD) were also determined to investigate the environmental mobility of these elements. In addition. the index of geoaccumulation and the Fe-normalized enrichment factor were calculated to differentiate the natural accumulation from the anthropogenic pollution. The vertical concentration profiles of heavy metals in core sediments indicate that surface enrichments (0~2 cm) of Pb, Zn, Cd and organic carbon were always observed at each core sample, due to the early diagenesis. However, the major factor contributing to the accumulation of Cd at the sediment surface is attributed to the dissolution of Cd from polluted roadside soil during periods of rainstorms and its subsequent redeposition on the sediment surface after being carried to the retention pond. A comparison of the KD values indiactes that a decrease in the KD values for Pb and Zn was observed with depth while KD values for Cd increase. According to the KD values. the relative mobility of studied metals was determined as following: Mn>Zn>Cd>Pb, for the upper layer, and Mn>Cd>Zn>Pb, for the lower layers.

• Korean Journal of Environmental Agriculture
• /
• v.40 no.3
• /
• pp.149-160
• /
• 2021

BACKGROUND: Concerns have been raised about the impact of recent high concentrations of fine dust on human health. Ammonia(NH₃) reacts with sulfur oxides and nitrogen compounds in the atmosphere to form ultrafine ammonium sulfate and ammonium nitrate (PM2.5). There is a growing need for accurate estimates of the amount of ammonia emitted during agricultural production. Therefore, in this study, ammonia emissions generated from the cultivation of leafy perilla in plastic houses were determined. METHODS AND RESULTS: Cow manure compost, swine manure compost, and poultry manure compost each at 34.6 ton ha^-1, the amount commonly used by farmers in the field, was sprayed on the soil surface. Just after spraying cow manure compost, swine manure compost, and poultry manure compost, the ammonia was periodically measured and analyzed to be 22.5 kg ha^-1, 22.8 kg ha^-1, and 85.2 kg ha^-1, respectively. The emission factors were estimated at 70.0 kg-NH₃ ton-N, 62.8 kg-NH₃ ton-N, and 234.1 kg-NH₃ ton-N, respectively. Most ammonia was released in the two weeks after application of the compost and then the amount released gradually decreased. CONCLUSION: Therefore, it is necessary to improve the emission factor through a study on the estimation of ammonia emission by type of livestock manure and major farming types such as rice fields and uplands, and to update data on the production, distribution, and sales of livestock manure.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.4
• /
• pp.37-45
• /
• 2010

Salt cementation, a typical naturally-cemented phenomenon, may occur due to water evaporation under the change of climate. Capillary force may influence the distribution of cement in granular soils. This study addresses the effect of capillary force on salt cementation using five different techniques: cone penetration test, electrical conductivity measurement, photographic imaging technique, nondestructive imaging technique, and process monitoring by elastic wave. Glass beads modeling a particulate media was mixed with salt water and then dried in an oven to create the cementation condition. Experimental results show that salt cementation highly concentrates at the top of the small particle size specimens and at the middle or the bottom of the large particle specimens. The predicted capillary heights are similar to the locations of high salt concentration in the cemented specimens. Five suggested methods show that the behavior of salt-cemented granular media heavily depends on the capillary force.

• Journal of Climate Change Research
• /
• v.10 no.3
• /
• pp.237-242
• /
• 2019

Ammonia is main precursor gas of secondary particulate matter and contributes almost 78% of total ammonia emission from the agricultural sector in Korea. The current method of estimating ammonia emission from fertilizer application, which contributes 7% of the total emission, has high uncertainty and needs to be improved to better predict PM2.5 concentration. In this study, we suggest an improvement method for ammonia emission quantification from fertilizer application. The first improvement was in the emission factor of NPK fertilizer by conducting a field study to verify the currently used factor. The improved NPK emission factor of 52.2 kg NH ton-1N was confirmed by comparing with the value from the EEA (European Environment Agency) and adjusting the value for the Korean climate and soil conditions. We also improved the amount of fertilizer usage by including the sales amount to the fertilizer supply amount of the Korean Farmers Association, increasing total fertilizer usage by 39.8%. As the statistical data on fertilizer supply and sales are compiled yearly, we estimated monthly emission of ammonia by considering cultivated areas and timing of fertilization for each crop. In summary, we suggest a novel and practical method to improve estimation methodology of ammonia emission from the field of fertilizer application: 1) emission factor of NPK fertilizer was reconfirmed; 2) total amount of fertilizer use was revised considering fertilizer sales; and 3) monthly emission of ammonia was realized by considering different crop practices. A bottom-up approach to compile activity data is needed to increase the estimation accuracy of monthly emission of ammonia, which is very helpful for predicting PM2.5 concentration.

• Analytical Science and Technology
• /
• v.23 no.4
• /
• pp.371-382
• /
• 2010

TSP and PM2.5 atmospheric aerosols have been collected at Gosan site of Jeju Island, and their compositions were analyzed to understand the pollution characteristics. The composition ratios of nss (non-sea salt)-$SO_4^{2-}$ and $NH_4^+$ were higher in Gosan site than those in other Korean background and urban sites. However the composition ratio of $NO_3^-$ was conversely lower in Gosan site. From the study of aerosol components according to particle sizes, the anthropogenic nss-$SO_4^{2-}$, $NO_3^-$ and $NH_4^+$ components were mostly existed in the fine particles. But the nss-$Ca^{2+}$, $Na^+$, $Cl^-$ and $Mg^{2+}$ originated from soil and marine sources were distributed relatively in the coarse particles. In the seasonal comparison, the concentrations of nss-$Ca^{2+}$, Al, Fe, Ca and $NO_3^-$ increased in spring season, and nss-$SO_4^{2-}$ showed higher concentration in summer and spring seasons. Based on the factor analysis, the atmospheric aerosols in Gosan site have been found to be influenced largely by anthropogenic sources, and next by marine and soil sources. The backward trajectory analyses showed that the concentrations of nss-$SO_4^{2-}$, $NO_3^-$, Pb and nss-$Ca^{2+}$ increased when the air mass moved from Chinese continent to Jeju area. On the other hand, their concentrations decreased when the air mass moved in from the North Pacific Ocean.

• Analytical Science and Technology
• /
• v.29 no.5
• /
• pp.209-218
• /
• 2016

PM₁₀ and PM_2.5 samples were collected at the 1100 site of Mt. Halla in Jeju Island during 2011~2012, and their ionic and elemental species were analyzed, in order to investigate the characteristics of emission sources as well as aerosol compositions. The mass concentrations of PM₁₀ and PM_2.5 were 22.0±13.1 µg/m³ and 11.3±6.1 µg/m³, respectively, showing 2.4~2.6 times lower than those of the capital city area of Korea. The composition ratios of major secondary pollutants (nss-SO₄²⁻, NH₄⁺, and NO₃⁻) were the highest as 85.5 % for PM₁₀ and 91.3 % for PM_2.5, and followed by the order of marine (Na⁺, Cl⁻, and Mg²⁺), organic acid (HCOO⁻ and CH₃COO⁻), and soil (nss-Ca²⁺) sources. Among the elemental species in PM₁₀, soil-originated components (Al, Fe, and Ca) were consisted of 50.9 %, which was higher proportion than marine and anthropogenic elements. The acidification of the fine particulate matters was found to be influenced mostly by sulfuric and nitric acids, and these acids were mainly neutralized by calcium carbonate in PM₁₀ and by ammonia in PM_2.5. The clustered back trajectories showed that 47 % of total air mass inflows was from the China, and the concentrations of NO₃⁻ and nss-Ca²⁺ were especially high corresponding to the inflows.

• Asian Journal of Atmospheric Environment
• /
• v.4 no.2
• /
• pp.97-105
• /
• 2010

A quantitative single particle analytical technique, denoted low-Z particle electron probe X-ray microanalysis (low-Z particle EPMA), was applied to characterize particulate matters collected at two underground subway stations, Jegidong and Yangje stations, in Seoul, Korea. To clearly identify the source of the indoor aerosols in the subway stations, four sets of samples were collected at four different locations within the subway stations: in the tunnel; at the platform; near the ticket office; nearby outdoors. Aerosol samples collected on stages 2 and 3 ($D_p$: $10-2.5\;{\mu}m$ and $2.5-1.0\;{\mu}m$, respectively) in a 3-stage Dekati $PM_{10}$ impactor were investigated. Samples were collected during summertime in 2009. The major chemical species observed in the subway particle samples were Fe-containing, carbonaceous, and soil-derived particles, and secondary aerosols such as nitrates and sulfates. Among them, Fe-containing particles were the most popular. The tunnel samples contained 85-88% of Fe-containing particles, with the abundance of Fe-containing particles decreasing as the distances of sampling locations from the tunnel increased. The Fe-containing subway particles were generated mainly from mechanical wear and friction processes at rail-wheel-brake interfaces. Carbonaceous, soil-derived, and secondary nitrate and/or sulfate particles observed in the underground subway particles likely flowed in from the outdoor environment by human activities and the air-exchange between the subway system and the outdoors. In addition, since the platform screen doors (PSDs) limit air-mixing between the tunnel and the platform, samples collected at the platform at the Yangjae station (with PSDs) showed a marked decrease in the relative abundances of Fe-containing particles compared to the Jegidong station (without PSDs).