• Journal of Pharmaceutical Investigation
• /
• v.17 no.1
• /
• pp.41-46
• /
• 1987

Oil in water microemulsion containing soybean oil and egg phosphatide was prepared by vacuum high shear mixing and high pressure homogenizing. The laser particle sizer, Coulter counter and photomicroscope were used to determine the particle size distribution at each cycle of homogenizing. Particularly, the laser particle sizer(dynamic light scattering method) was applied to the study of particle size distribution behavior below $1\;{\mu}m$. It was found that the particle size distribution below $1\;{\mu}m$ was shifted to lower size range as the number of passing cycle was increased. Beyond the 7th cycle, however, the particle size distribution was not varied.

• The Journal of the Korea Contents Association
• /
• v.20 no.12
• /
• pp.537-546
• /
• 2020

This study deals with the development and improvement of a particle dispersion model for quick response to water pollutant accidents. The developed model is based on the shear dispersion theory where vertical mixing is done by step by step mixing by vertical and molecular diffusion algorithm. For the quick response to chemical accidents, an algorithm for multi-core modeling for the particle dispersion model is applied. After the application of multi-core operation using OpenMP directives to the model, the relation for the calculation time and particle size were determined along with the number of cores used for parallel programming to determine the model time for chemical accident responses. The results showed the adequate conditions for the modeling of chemical accidents for quick response and to increase the applicability of the model.

• Polymer(Korea)
• /
• v.39 no.3
• /
• pp.441-452
• /
• 2015

Twin-screw kneader is an efficient polymer processing equipment. In this paper, the mixing performance of one novel intermeshing counter-rotating twin-screw kneader with different tip angles of the male rotor is simulated using the mesh superimposition technique (MST). Statistical analysis is carried out for the flow field using particle tracking technique, and distributive mixing performance is evaluated using the residence time distribution and segregation scale, while the dispersive mixing performance is estimated using the parameters such as shear rate, stretching rate and mixing index. The results show that the best distributive mixing performance is achieved when the tip angle is 0o, while the optimal dispersive mixing performance is obtained when the tip angle is 20o. The results in this paper provide a data basis for the selection of parameters and optimization of the performance for the screw rotors.

• 한국연소학회:학술대회논문집
• /
• 2005.10a
• /
• pp.231-237
• /
• 2005

Interruption of good fluidization in a fluidized bed ash cooler(FBAC) for discharging bed materials such as sand or coal ash particles from the CFB combustor is frequently happened because of agglomeration of the particles in the bed. This unstable operation may, in the worst case, result in an unscheduled boiler shut down. In this study, we examined the operation problems of the FBAC of Tonghae CFB boiler and studied and introduced the simple detection and solution techniques with analyzing the mixing property and the occurrence of defluidization in a simulated fluidized bed ash cooler system (0.5m-H x 0.5m-W x 1.0m-L). The bridge of the large particles at the bed surface could be observed, and this caused to form the defluidization area at the entrance of the FBAC. The defluidization was affected not only by airflow rates but also by the particles discharging rates as well as particle size distribution in the FBAC. The local defluidization could be detected by analysis of the accumulated standard deviation error at a given period of time. Also, the regulation of the overall or local airflow rate made clearing up the local defluidization possible.

• Journal of Korean Society for Quality Management
• /
• v.42 no.4
• /
• pp.579-590
• /
• 2014

Purpose: Ball milling is a popular process for obtaining fine powders in the part and material industry. One of important issues in the ball milling is to produce particles with a uniform size. Although many factors affect uniformity of particles, this paper focuses on the choice of ball diameter. Consider a ball milling where balls can be taken with three different diameters. The purpose of this paper is to find a ball mix which minimizes the average particle size. Methods: Ball diameters are selected as 10mm, 3mm, and 0.5mm. In order to find an optimum mixing ratio, the method of mixture experiments is employed in this paper. Taguchi's signal-to-noise ratio (SNR) for smaller-the-better type is also used to analyze experimental data. Results: According to the experimental result, SNR is maximized when the ball mix is taken as either 7:3:0 or 6:4:0. Such mixing ratios can be technically validated in terms of porosity reduction. Conclusion: The ball mixing technique presented in this paper provides a useful way to improve the production efficiency with a low cost.

• Journal of the Korean Society of Visualization
• /
• v.6 no.2
• /
• pp.14-19
• /
• 2008

In this paper, the recirculation flow motion and mixing characteristics driven by air bubble flow in a rectangular water tank is studied. The Time-resolved PIV technique is adopted for the quantitative visualization and analysis. 532 nm Diode CW laser is used for illumination and orange fluorescent particle images are acquired by a PCO 10bit high-speed camera. To obtain clean particle images, 545 nm long pass optical filter and an image intensifier are employed and the flow rates of compressed air is changed from 2 l/min to 4 l/min at 0.5 MPa. The recirculation and mixing flow field is further investigated by the POD analysis technique. It is observed that the large scale counterclockwise rotation and main vortex is generated in the upper half depth from the free surface and one quarter width from the sidewall. When the flow rates are increased, the main vortex core is moved to the side and bottom wall direction.

• Journal of the Korean Society of Visualization
• /
• v.6 no.1
• /
• pp.41-46
• /
• 2008

In this paper, the recirculation flow motion and mixing characteristics driven by air bubble stream in a rectangular water tank is studied. The time-resolved PIV technique is adopted for the quantitative visualization and analysis. 488 nm Ar-ion CW laser is used for illumination and orange fluorescent ($\lambda_{ex}=540nm,\;\lambda_{em}=560nm$) particle images are acquired by a PCO 10bit high-speed CCD camera (1280$\times$1024). To obtain clean particle images, 545 nm long pass optical filter and an image intensifier are employed and the flow rates of compressed air is 3 l/min at 0.5 MPa. The recirculation and mixing flow field is further investigated by time-resolved POD analysis technique. It is observed that the large scale recirculation resulting from the interaction between rising bubble stream and side wall is the most dominant flow structure and there are small scale vortex structures moving along with large scale recirculation flow. It is also verified that the sum of 20 modes of velocity field has about 67.4% of total turbulent energy.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.6
• /
• pp.601-605
• /
• 1999

$LiCoO_2$and $LiCo_{1-x}$$Ni_x$$O_2$ solid solutions were fabricated by the solid state reaction process. The structural cation mixing phenomena were investigated using XRD, SEM, particle size analysis and $^7$Li NMR,The synthesized LiCoO$_2$ and $LiCo_{1-x}Ni_XO_2$ microcrystallines showed the hexagonal layered structures. Mean particle sizes were increased with the increase of the amount of nickel in the solid solutions. The cation mixing effects were increased as increasing the fraction of nickel(x), x = 0.3, 0.5, 0.7. the peak frequency of $^7$Li NMR was shifted to the higher frequency and the line width increased as increasing the amount of nickel in the solid solutions.

• Polymer(Korea)
• /
• v.26 no.6
• /
• pp.803-811
• /
• 2002

In this study the wear behavior of ultra high molecular polyethylene (UHMWPE) filled with kaolin particles by different methods was investigated. UHMWPE/kaolin composites were prepared by two different methods: polymerization-filling and powder mixing. Particularly in a powder mixing method. Particle dispersion and wear property according to powder mining method were examined. It was found from wear test that filling of inorganic filler into UHMWPE by polymerization filling was more effective way than by powder mixing method in improving Wear resistance of UHMWPE. It was also confirmed that abrasive wear was dominant wear mechanism and particle dispersion in the composite as well as interface property was an important factor in controlling the wear behavior of the resulting composites.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03a
• /
• pp.171-175
• /
• 2008

In the present study, a numerical simulations are investigated in a stirred solid/liquid system by using Eulerian multi-phase model. The transient flow field of liquid phase and distribution of solid particles are predicted in stirred tanks consisting of 4-pitched paddles impeller and baffles. The effects of number and width of baffles on the mixing time and the quality of solid suspension in a stirred tank are presented numerically. The result shows that the mixing time decreases as the width and number of baffles increase.