• Journal of the Korean Institute of Landscape Architecture
• /
• v.25 no.2
• /
• pp.54-61
• /
• 1997

This study has conducted to analyze the crelationship among soil properties and to investigate how they affect soil physical characteristics and plant growth. The experiment of woody plant growth was conducted as follows : Type I was the original soil. Type II, the soil particles smaller than 20${\mu}{\textrm}{m}$ was removed from the original soil. Type III, the soil particles is smaller than 75${\mu}{\textrm}{m}$ was removed from original soil. Wisteria floribunda A.P.DC and Celtis sinensisi Pers. were used for plant growth measurement. 1. Soil type II. the closest to Fuller's curved line, showed high dry bulk density and low in soil pores and saturated hydraulic conductivities. This created poor soil aeration and limited space for the root to growth. When the root did not have sufficient space to grow, there was a lot of physical stress, which hindered the root growth. 2. Soil typeIII was high saturated hydraulic conductivity and a lot of soil pores larger than 10 ${\mu}{\textrm}{m}$. As a result, there were more available spaces for root to spread. It was considered that there was less physical stress for root growth. Therefore, soil typeIII showed significantly greater root growth. 3. Because soil type III has less small particles and saturated hydraulic conductivity was high, and water infiltrates rapidly into the underground when there was rainfall or irrigation. The soil typeIII becomes much stronger soil mechanically due to the less small particles. Therefore, soil typeIII was a suitable material for applying on planting sites where soil compaction is expected.

• Resources Recycling
• /
• v.18 no.6
• /
• pp.18-23
• /
• 2009

An investigation on the synthesis of aluminum citrate, one of the aluminum organic compounds, has been performed using aluminum chloride solutions as a starting material. For the synthesis of aluminum citrate, citric acid was added to aluminum solutions with the mole ratio of citric acid to aluminum to be 2.5 and aluminum citrate synthesized was also characterized in terms of chemical analysis, X-ray diffraction, particle size measurement and SEM analysis. As a result, it was found that the ratio of ethanol/Al solution more than 4.0 was required for the synthesis of aluminum citrate from aluminum solutions. Furthermore, the pH should be controlled to be more than 7.0 in order to obtain the recovery of aluminum citrate higher than 97%. From the chemical analysis of aluminum citrate synthesized in this work, the content of $NH_4$, Al and C was found to be 17.0, 4.01 and 25.7%, respectively. Accordingly, the aluminum citrate synthesized from aluminum solutions was confirmed to be $(NH_4)_5Al(C_6H_4O_7)_2{\cdot}2H_2O$.

• Bulletin of the Korean Space Science Society
• /
• 2010.04a
• /
• pp.38.3-39
• /
• 2010

While major solar proton events (SPEs) come from the coronal mass eject (CME)-driven shocks in solar wind, there are many evidences that potentiality of CMEs to generate SPEs depends on its early evolution near the Sun and on different solar activities observed around the CME liftoff time. To decipher origin of SPE release, we have investigated onset time comparison of the SPE with CME, metric type II radio burst, and hard X-ray flare. For this, we select 30 SPEs observed from 1997 to 2006 by using the particle instrument ERNE onboard SOHO, which allows proton flux anisotropy measurement in the energy range ~10 - 50MeV. Onset time of the SPEs is inferred by considering the energy-dependent proton transport time. As results, we found that (1) SPE onset time is comparable to that of type II but later than type III onset time and HXR start time, (2) SPE onset time is mostly later than the peak time of HXR flare, (3) almost half of the SPE onsets occurred after the HXR emission, and (4) there are two groups of CME height at the onset time of SPE; one is the height below 5 Rs (low corona) and the other is above 5Rs (high corona). In this talk, we will present the onset time comparison and discuss about the origin of the SPE onset.

• Applied Biological Chemistry
• /
• v.28 no.4
• /
• pp.271-277
• /
• 1985

A polarograph with specially designed cell compartment usable in kinetic study of the mitochondrial respiration of a small sized sample was made, and its performance and experimental conditions were examined. An applied potential (ca-1.2V vs. SCE) which gives rise to the second step reduction of oxygen caused a considerable level of a residual current independent of oxygen, which is temporarily interpreted as the reduction current of the membrane-bound redox material(s) of mitochondria. A potential corresponding to the first slop reduction of oxygen (ca-0.4V vs SCE) did not produce the residual current. Thus, it is suggested that a measurement of oxygen concentration in a sample of mitochondria and submitochondrial particles by using dropping mercury electrode should be done with an applied potential of about -0.4V vs SCE. Consumption of oxygen by mitochondria was observed to follow practically zero order kinetics. Its rate constant exhibited the proportional relationship with the respiratory activity of mitochondria. Usefulness of tile instrument was properly demonstrated in the work on the temperature effect on the respiration of mitochondria isolated from several plant 4issues which were selected on the basis of chilling susceptivity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.6
• /
• pp.1302-1307
• /
• 2006

This study describes the preparation of high-performance photocatalyst and its environmental applications. We prepared visible-light response nano-particle photocatalyst exhibiting the similar photocatalytic activity with $TiO_2$, dispersed $TiO_2$ on $SiO_2$ with an active rutile type titanium oxide prepared at low temperature. The binder and stable photocatalytic $TiO_2$ sol for photocatalytic system were also prepared. Such products were evaluated by UV/Vis spectrometer, X-ray diffraction analysis, SEM, measurement of photocatalytic activities and surface area, mechanical properties of $TiO_2$-coated surfaces. The results obtained can be applied in efficient photocatalytic systems using POF and metal plate for the purification of air.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.10
• /
• pp.662-667
• /
• 2014

B-doped Si nanoparticles were synthesized by using inductive coupled plasma and specially designed double tube reactor, and their microstructures were investigated. 0~10 sccm of $B_2H_6$ gas was injected during the synthesis of Si nanoparticles from $SiH_4$ gas. Highly crystalline Si nanoparticles were synthesized, and their crystallinity did not change with increase of $B_2H_6$ flow rates. From SEM measurement, their particle sizes were approximately 30 nm regardless of $B_2H_6$ flow rates. From SIMS analysis, almost saturation of B in Si nanoparticles was detected only when 1 sccm of $B_2H_6$ was injected. When $B_2H_6$ flow rate exceeded 5 sccm, higher concentration of B than solubility limit was detected even if any secondary phase was not detected in XRD or HR-TEM results. Due to their high electronic conductivity, those heavily B-doped Si nanoparticles can be a potential candidate for an active material in Li-ion battery anode.

• Journal of Welding and Joining
• /
• v.27 no.6
• /
• pp.68-73
• /
• 2009

Recently, as titanium and titanium alloys are being increasingly used in wide areas, there are on-going researches to obtain high quality weld zone. In particular, growing interest is being drawn to laser welding, which involves low heat input and large aspect ratio in various welding processes and can facilitate shield in atmospheric condition compared with electron beam welding. The first report covered the analysis of embrittlement by the bead color of weld zone through quantitative analysis of oxygen and nitrogen and measurement of hardness as basic experiment to apply laser welding to titanium. Results indicated that the element that affect embrittlement the most was nitrogen, and as embrittlement and oxygenation go on, bead color changed to silver, gold, brown, blue and gray. This study performed butt welding of pure titanium and STS304 by using 1kW CW Nd:YAG laser, and to find out basic physical properties, evaluated welding performance by laser output, welding speed, root gap and misalignment etc, and examined mechanical properties through tensile stress and Erichsen test. The reason particles of pure titanium welded metal and HAZ are greater than STS304 is because they are pure metal and do not include many impure elements that work as nuclei in case of resolidification, thus becoming coarse columnar crystals eventually. In addition, the reason STS304 requires more energy during welding than pure titanium is because the particle size of base metal is smaller.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.10
• /
• pp.985-993
• /
• 2012

In this paper, a new method is proposed to estimate the sound pressure generated from gasoline direct injection (GDI) engine. There are many noise sources as much as components in GDI engine. Among these components, fuel pump, fuel injector, fuel rail, pressure pump and intake/exhaust manifolds are major components generated from top of the engine. In order to estimate the contribution of these components to engine noise, the total sound pressure at the front of the engine is estimated by using airborne source quantification (ASQ) method. Airborne source quantification method requires the acoustic source volume velocity of each component. The volume velocity has been calculated by using the inverse method. The inverse method requires many tests and has ill-condition problem. This paper suggested a method to obtain volume velocity directly based on the direct measurement of sound intensity and particle velocity. The method is validated by using two known monopole sources installed at the anechoic chamber. Finally the proposed method is applied to the identification and contribution of noise sources caused by the GDI components of the test engine.

• Journal of Navigation and Port Research
• /
• v.35 no.10
• /
• pp.805-810
• /
• 2011

An experiment was carried out to figure out the instantaneous flow characteristics in the wake of the transom stern's 2-dimensional section by 2-frame grey level cross correlation PIV method at $Re=3.5{\times}103$, $Re=7.0{\times}103$. The stern angles of models were learning at $45^{\circ}$(Model "A"), $90^{\circ}$(Model "B") and $135^{\circ}$(Model "C") respectively based on the survey results of real ships. The depth of wetted surface is 40mm from free surface. As Reynolds number increases, vortices increase in volume and move their way to the downstream. Flow separation appeared at the end of model's bottom.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.3
• /
• pp.74-83
• /
• 1998

The phenomenon of decrease in sizing efficiency when the stock temperature is increased is well recognized as summer sizing, and this is believed to be caused by uneven distribution of sizing agents on paper surface most often incurred by coagulation of sizing agents. When unevenly sized paper is used as coating base stock, nonuniform consolidation of the coating layer may result, which, in turn, causes uneven distribution of binder on coating surface. This causes nonuniform ink absorption to produce print mottle. In this study the effects of simple or polymeric electrolytes, storage temperature and time on the coagulation of cationic dispersed rosin size were investigated using a turbidity measurement method which was verified to correlate well with the particle size of rosin emulsion or its coagulates. Handsheets sized with rosin dispersions coagulated under various conditions were prepared and their sizing degree and coated paper properties including gloss and ink density were examined. The relationship between the sizing nonuniformity of coated papers and its ink absorption property was evaluated. Turbidity of rosin emulsion increased as the storage temperature and time were increased. Addition of simple or polymeric electrolytes caused reduction in $zeta$ -potential of the rosin dispersion and accelerated the coagulation tendency substantially. Reversion of the $zeta$ -potential of rosin dispersion, however, did not occur when coagulation was induced with simple electrolytes. On the other hand, addition of an anionic polyelectrolyte reversed the $zeta$ -potential of the flocculated rosin dispersion. This indicated that electrical double layer compaction and bridging flocculation were coagulation mechanisms for simple and polymeric electrolytes, respectively. Sizing degree decreased as coagulation of rosin was increased. Paper gloss, ink gloss and ink density were increased when sizing degree of base stock was increased most probably due to prevention of base paper swelling and increased binder migration to coating surface. This suggested that uneven printing ink density occurred when uneven sizing development was induced by coagulation of rosin particles.