• The Journal of Engineering Geology
• /
• v.30 no.3
• /
• pp.269-278
• /
• 2020

In this study, the effects of groundwater artificial recharge through vertical wells in the upper small basin are preliminarily evaluated by using field injection test and a 3-D numerical model. The injection rate per well in a model is set to 20, 37.5, 60, and 75 ㎥/day based on the results of field injection test, groundwater levels, and hydraulic conductivities estimated from particle size analysis, and a numerical model using MODFLOW is conducted for 28 cases, which have diverse injection intervals, in order to estimated the changes of groundwater level and water balance after injection. Groundwater level after injection does not show a linear relationship with the injection rate per well, and the cumulative effect of artificial recharge decreases and the timing of maximum water level rise is shortened as the injection interval becomes longer. In four cases of continuous injection with total injection rate of 1,200 ㎥, it is revealed that the recharge effect is analyzed as 36.5~65.3% of the original injection rate. However, it will be more effective if the artificial recharge system combined with underground barrier is introduced for the longer pumping during a long and severe drought. Additionally, it will be possible to build a stable artificial recharge system by an establishment of efficient scenario from recharge to pumping as well as an optimization of recharge facilities.

• Korean Journal of Food Science and Technology
• /
• v.23 no.6
• /
• pp.732-738
• /
• 1991

Corsoy 79 soybeans were ground into 8-(coarse) and 24-mesh (fine) full-fat soy flours. From the particle size analysis, the 8-mesh full-fat soy flours were found to have larger values for geometric mean diameter and geometric standard deviation. However, the distribution moduli of coarse and fine soy flours were similar and indicated soybeans were nearly 'brittle'. Development of hydrolytic and oxidative rancidities of coarsely and finely ground full-fat soy flours were followed from grinding to 24 hrs later. No increases in peroxide value and conjugated dienes in the oil and hexanal content in the headspace of the flour were observed when the moisture was 10.7% or less. At 14.9% moisture and above, lipid oxidation increased with increased moisture content and storage time. Free fatty acid contents increased slightly at all moisture contents. However, hydrolysis did not exceed 0.06% over the moisture range of 4 to 18%, which is of little practical significance. Fine grinding increased oxidative and hydrolytic rancidities, especially at 14.9% moisture and above. these findings indicate that raw soybeans can be ground to full-fat soy flours and stored up to 24 hrs without undergoing significant lipid and flavor deterioration if the moisture content is 11% or less.

• Journal of Korean Society for Atmospheric Environment
• /
• v.25 no.6
• /
• pp.493-502
• /
• 2009

The concentrations of outdoor airborne bacteria measured in Seoul, Korea for one year (Jan. 2008~Dec. 2008) ranged from $500CFU/m^3$ to $7,500CFU/m^3$. In monthly concentration distribution, the level of outdoor airborne bacteria was highest in September and October and lowest in March. In seasonal concentration distribution, the order of level of outdoor airborne bacteria was autumn>winter>spring>summer. In regional concentration distribution, the highest level of outdoor airborne bacteria was generally found in the forest, followed by general area and traffic site. In distribution characteristics according to particle size, outdoor airborne bacteria showed 31% for >$7.0{\mu}m$ (stage 1), 21% for $4.7{\sim}7.0{\mu}m$(stage 2), 15% for $3.3{\sim}4.7{\mu}m$(stage 3), 19% for $2.1{\sim}3.3{\mu}m$(stage 4), 10% for $1.1{\sim}2.1{\mu}m$(stage 5), and 4% for $0.65{\sim}1.1{\mu}m$(stage 6) and its mean respirable fraction was 48%. In concentration distribution by yellow dust, the mean levels of outdoor airborne bacteria were 803 $(\pm479)CFU/m^3$ for period of yellow dust and 691 $(\pm1,134)CFU/m^3$ for period of non-yellow dust. Although the level of outdoor airborne bacteria was higher in period of yellow dust than period of non-yellow dust, there was no significant difference between period of yellow dust and non-yellow dust (p>0.05). In correlation analysis between outdoor airborne bacteria and atmospheric factors (temperature and relative humidity), there was no significant correlation between outdoor airborne bacteria and atmospheric factors. The predominant airborne bacteria were identified to the Bacillus-derived species.

• Journal of Conservation Science
• /
• v.35 no.6
• /
• pp.600-611
• /
• 2019

Yellow to reddish brown soil is generally referred to as hwangto and is used in various industries in Korea. Despite the fact that it is used as an inorganic pigment in dancheong, limited studies have been conducted on the properties of pigments associated with soil and on the mineralogical characteristics of hwangto. This study examines how the pedological and mineralogical features of hwangto affect pigment properties. Results indicate that reddish and yellowish soils have differences in terms of soil texture, mineral composition, oil absorption and stability under light. Reddish soil is mostly found in clay regions, whereas Ulleungdo hwangto is found in loam regions. Yellowish soil is mostly present in the clay loam to loam zones. whereas Haenam hwangto exists in the sandy clay loam zone. As a result of a mineralogical analysis, reddish soil is classified into the feldspar group and clay soil. The major minerals in the yellowish soils are similar however these soils differ in terms of clay mineral compositions. results of the characteristics of pigments prepared by the traditional method revealed that the average particle size is in the range of 10-20 ㎛, reddish soil has an average of 20 ml/100 g higher oil absorption than yellowish soil. In addition, reddish soil is more susceptible to discoloration and deterioration under light than yellowish soil. This study confirms that the soil and mineral characteristics of hwangto affect the physical properties and stability of produced pigments. These result can be used as basic data in future studies natural inorganic pigments using hwangto.

• Journal of Conservation Science
• /
• v.30 no.4
• /
• pp.457-466
• /
• 2014

Rigorous analysis was performed to identify the structure and materials of the murals to study techniques used on mural tombs of ancient Daegaya era(6th century). The murals were painted by applying mortar on the walls and the ceiling after building a stone chamber and creating ground layers on mortar layers. Mud was applied on most of the mortar layers on four sides of the walls except the ceiling. Sand was not used in mortar but was made of materials with pure calcium substances. In addition, shells in irregular sizes with incomplete calcination were mixed; and the mortar's white powder was inferred as lime obtained by calcination of oyster shells. Kaolinite($Al_2Si_2O_5(OH)_4$) was used in the ground layer, Cinnabar(HgS) was used for red pigment, Malachite($Cu_2CO_3(OH)_2$) for green and Lead white($PbCO_3{\cdot}Pb(OH)_2$) for white. Mud plaster was applied on the mortar and was composed thinly and densely using clayey of particle size smaller than that of medium sand. It was assumed that the finishing was for repair after long time had passed since the mortar layer came off. Using lime made with oyster shells as mortar is unprecedented in ancient Korean mural tombs and its durability was very poor, suggesting that Gaya's mortar production technique was relatively behind compared to that of Koguryo's in the same era.

• Journal of the Korean Applied Science and Technology
• /
• v.24 no.2
• /
• pp.174-181
• /
• 2007

In this study, $SiO_2/poly(ethylene-co-vinyl$ alcohol)(EVOH) hybrid coating materials with gas barrier property could be produced using sol-gel method. The biaxially oriented polypropylene (BOPP) substrate with surface pretreatment was coated with the prepared hybrid sols containing various inorganic silicate component by a spin coating method. Crystallization behavior of the hybrids was investigated in terms of analysis of X-ray diffraction and cooling thermogram from DSC experiment. From the morphological observation of the $SiO_2/EVOH$ hybrid gel, it was confirmed that there existed an optimum content of inorganic silicate precursor, Tetraethylorthosilicate (TEOS), to produce hybrid materials with dense microstructure, exhibiting uniformly dispersed silica particles with average size below 100 nm. When TEOS was added at below or above the optimum content, particle clusters with large domain were observed, resulting in phase separation. This morphological result was found to be in good agreement with that of oxygen permeability of the hybrid coated films. In the case of film coated with hybrid prepared from addition of 0.01 - 0.02mol of TEOS, a remarkable improvement in barrier property could be obtained, however, with the addition of TEOS more than 0.04 mol, the barrier property was dramatically reduced because of phase separation and micro-crack formation on the film surface.

• Resources Recycling
• /
• v.18 no.5
• /
• pp.19-25
• /
• 2009

Molybdenite concentrate ($MoS_2$) is the major mineral for the molybdenum industry, of which the industrial processing is first converted to technical grade molybdenum trioxide ($MoO_3$) by its oxidative roasting and purification, used as a raw material for manufacturing several molybdenum compounds. In the present work, detailed experimental results for the oxidative roasting of low grade Mongolian molybdenite concentrate are presented. The experiments were carried out in the temperature range of 793 to 823 K under an oxygen partial pressure range of 0.08 atm to 0.21 atm by using a thermogravimetric analysis technique. The molybdenite concentrate was an average particle size of $67\;{\mu}m$. In the oxidative roasting of low grade Mongolian molybdenite concentrate, more than 95% of molybdenite was converted to molybdenum trioxide in 60 min. at 828 K. The lander equation was found to be useful in describing the rates of the oxidative roasting and the reaction order with respect to oxygen concentration in a gaseous mixture with nitrogen was 0.11 order.

• Korean Journal of Veterinary Service
• /
• v.31 no.3
• /
• pp.385-395
• /
• 2008

This study was carried out to investigate the residue level of fluoroquinolones in hen's general eggs and specific eggs by microbiological assay method and high performance liquid chromatography (HPLC) method. HPLC separation was carried out by reversed phase chromatography on a Symmetry $C_{18}$ (250${\times}$4.6 mm, $5{\mu}m$ particle size) with a phase composed of distilled water (containing 0.4% triethylamine and phosphoric acid) : Methanol (780 : 220, v/v), pumped isocratically at a flow rate of 1.0ml/min. A fluorescence detector was utilized with an excitation wavelength of 278nm and an emission wavelength of 456nm. The calibration curves were linear $({\gamma}^2{\geq}0.999)$ over a concentration range of $0.025{\sim}0.4{\mu}g/ml$. Average recoveries of the five fluoroquinolones in whole eggs at fortified levels of $0.05{\sim}0.2{\mu}g/g$ were ranged mean $78.1{\sim}91.7%$ and low coefficient of variation was less than 10% for all analysed samples. The limits of detection and limits of quantification for whole eggs were $1.2{\sim}6.0ng/g$ and $2.3{\sim}9.1ng/g$, respectively. Only one hen's general eggfrom chicken farm in Incheon was detected with the residual fluoroquinolones (Microbiological assay method; 1 of 47 general eggs) ; the range of residual concentration enrofloxacin was 0.12ppm. Those in food stores were detected with the residual fluoroquinolones (Microbiological assay method; 4 of 88 general eggs) ; the ranges of residual concentration enrofloxacin were $0.15{\sim}2.2 ppm$, ciprofloxacin $0.01{\sim}0.06ppm$, and hen's specific eggs (40) in food stores were not detected. For the microbiological assay method of fluoroquinolones in hen's eggs, as the results of comparative analysis, the disc diffusion method with E coli may be a little highly detected for the residual fluoroquinolones.

• Journal of the Mineralogical Society of Korea
• /
• v.27 no.3
• /
• pp.115-124
• /
• 2014

In order to leach Au and Ag from gold-silver bearing sulfide concentrate, the sulfide concentrate was ground in a ball mill for a dry pre-treatment and a wet pre-treatment process. Mineralogical studies and thiourea leaching experiments were carried out with the pre-treated sulfide concentrate. The results of the pre-treatment with the concentrate samples showed the mean particle size and iso-electrical potential was smaller in the dry pre-treatment sample than in the concentrate sample, and the contents was lower in the wet pre-treatment sample than in the dry pre-treatment sample. In XRD analysis, amorphous properties were only shown in the wet pretreatment sample. The results of the concentrate sample leaching experiments showed that the best Au, Ag leaching parameters were when the addition of thiourea was at a 1.0 g concentration, ferric sulfate was 1.0 M, sulfuric acid was 2.0 M and the leaching temperature was at $60^{\circ}C$. The Au, Ag leaching rate was always much greater and faster with the wet pre-treatment samples than with the dry pre-treatment samples. Accordingly, it is expected that more Au, Ag can be leached in an eco-friendly methodology using wet pre-treatment. The pre-treatment could be improved with an optimized grinding additive reagent and through researching grinding time in future non-cyanide processes.

• Journal of the Korea Concrete Institute
• /
• v.21 no.6
• /
• pp.713-718
• /
• 2009

Advanced industries-IT, BT, NT and ET are rapidly developing in 21 century. And the cement industry is becoming the principal factor in air pollution because of the creation of $CO_2$ during manufacturing. Also, the cement industry will be faced with a crisis due to the exhaustion of natural resources. In this study, nano cement by Bottom-up method of a chemical synthesis was developed. The generation of $CO_2$ during the plasticization process of cement manufacturing was avoided. The purpose was to produce building materials that have both high strength and durability as the high value-added growth engine industry of the 21 century. The nano cement was developed using hydrothermal synthesis. This is a method of mixing after ripening, by manufacturing the high density gel and low gel, which does not require special test equipment or pressure conditions to produce. Particle size, SEM, EDX, and porosity tests were conducted. This study investigated the compressive strength of concrete with various compositions. Specimens were tested for compressive strength at 3, 7, 14 and 28 days. The medium-sized (50% by weight) cement particles created by chemical synthesis were less than 168 nm. The compressive strength of the mortar prepared using this cement was 53.9 MPa. But it was judged that succeeding study will be necessary for development of nano building materials with high ability and economical analysis.