• Journal of the Korea Concrete Institute
• /
• v.21 no.5
• /
• pp.589-597
• /
• 2009

High Performance Fiber-reinforced Cement Composite (HPFRCC) shows the multiple crack and damage tolerance capacity due to the interfacial bonding of the fibers to the cement matrix. For practical application, it is needed to investigate the fractural behavior of HPFRCC and understand the micro-mechanism of cement matrix with reinforcing fiber. This study is devoted to the investigation of the AE signals in HPFRCC under monotonic and cyclic uniaxial compressive loading, and total four series were tested. The major experimental parameters include the type and volume fraction of fiber (PE, PVA, SC), the hybrid type and loading pattern. The test results showed that the damage progress by compressive behavior of the HPFRCC is a characteristic for the hybrid fiber type and volume fraction. It is found from acoustic emission (AE) parameter value, that the second and third compressive load cycles resulted in successive decrease of the amplitude as compared with the first compressive load cycle. Also, the AE Kaiser effect existed in HPFRCC specimens up to 80% of its ultimate strength. These observations suggested that the AE Kaiser effect has good potential to be used as a new tool to monitor the loading history of HPFRCC.

• Korean Journal of Agricultural Science
• /
• v.7 no.1
• /
• pp.1-5
• /
• 1980

In order to evaluate cold tolerance and to counter measure the cold damage of newly released rice varieties, the effects of degree and duration of low temperature at the meiotic stage on the sterility and ripening of rice spikelets were investigated and the results were as follows: 1. As the temperature was lowered and the duration of low temperature was extended during the meiotic stage, the heading dates were delayed and the sterility were increased. The main factor for the low yield due to low temperature was due to the increased sterility, and under the below $15^{\circ}C$, the delayed heading was also responsible for the low yield. 2. The sterility and delayed kernel development of rice were increased when grown at $15^{\circ}C$ for six days. 3. The newly released rice varieties were highly sensitive te low temperature damage during the meiotic stage. The treatment of rice at $15^{\circ}C$ for four days might be used as a perameter to evaluate the low temperature tolerance of rice varieties.

• Korean Journal of Environmental Biology
• /
• v.34 no.4
• /
• pp.264-271
• /
• 2016

The objective of this study was to determine the growth and light utilization efficiency of garden plants in shade area through chlorophyll fluorescence reaction analysis. Ten garden plants was grown for 75 days under 50% and 80% shading conditions. Under shading, $ET2_O/RC$, the fluorescence parameter related to electron-transport in photosystem II, was effectively enhanced. However, the electron transport flux until PSI acceptors per reaction center ($RE1_O/RC$) was reduced. These changes in photochemical parameters evoked a decrease in performance index (PI) and driving force (DF) of electron transport flux. In addition, some photochemical parameters such as $F_V$, $FV/F_O$, $RE1_O/RC$, $ET2_O/RC$, $PI_{TOTAL\;ABS}$, and $DF_{TOTAL\;ABS}$ were found to be important for shade tolerance. Three species (Pachysandra terminalis Siebold & Zucc, Physostegia virginiana L., and Carex maculata Bott) were found to be shade tolerant. Based on these results, shading factor index (SFI) deduced from photochemical parameters is useful for evaluating of shading stress of garden plants.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.19 no.2
• /
• pp.173-181
• /
• 2001

It is very important to assess spatial data quality of a digital map produced through digital map generalization. In this study, as a aspect of spatial data quality maintenance, we examined the tolerate range of theoretical expectation accuracy and established the quality assessment standard in spatial data for the transformed digital map data do not act contrary to the digital map specifications and the digital map accuracy of the relational scale. And, transforming large scale digital map to small scale, if we reduce complexity through processes as simplification, smoothing, refinement and so on., the spatial position change may be always happened. thus, because it is very difficult to analyse the spatial accuracy of the transformed position, we used the buffering as assessment method of spatial accuracy in digital map generalization procedure. Although the tolerated range of generic positioning error for l/l, 000 and l/5, 000 scale is determined based on related law, because the algorithms adapted to each processing elements have different property each other, if we don't determine the suitable parameter and tolerance, we will not satisfy the result after generalization procedure with tolerated range of positioning error. The results of this study test which is about the parameters of each algorithm based on tolerated range showed that the parameter of the simplification algorithm and the positional accuracy are 0.2617 m, 0.4617 m respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.3
• /
• pp.57-62
• /
• 2012

In this paper, numerical analysis by finite element method, parameter design by the Taguchi method and ANOVA method were used to analyze about effect of design deviations and thickness variations on warpage of FCCSP substrate. Based on the computed results, it was known that core material in substrate was the most determining deviation for reducing warpage. Solder resist, prepreg and circuit layer were insignificant effect on warpage relatively. But these results meant not thickness effect was little importance but mechanical properties of core material were very effective. Warpage decreased as Solder resist and circuit layer thickness decreased but effect of prepreg thickness was conversely. Also, these results showed substrate warpage would be increased to maximum 40% as thickness deviation combination. It meant warpage was affected by thickness tolerance under manufacturing process even if it were met quality requirements. Threfore, it was strongly recommended that substrate thickness deviation should be optimized and controlled precisely to reduce warpage in manufacturing process.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.6
• /
• pp.607-613
• /
• 2009

In this paper, we made a simple paper feeding system which is one of MTS (media transport system) and controllers. The plant has a flexible paper and two driving rollers and two driven rollers. The control system has two conventional PID controllers. Skew angle and feeding speed of MTS deteriorate the quality of feeding system. In order to control a feeding speed and skew of feeding paper, we control rotational velocity of two driving rollers. Therefore, this controller has two inputs and two outputs as MIMO (multi-input and multi-output) system. The control inputs were the feeding speed and the skew displacement of the paper. The control outputs were the rotational velocity to each driving roller. To find appropriate PID gains of two controllers, we proposed an optimization technique. We assume the system variables and performance of a whole system as follows. PID gains of two controllers for skew and feeding speed are system variables. System performance is both skew and feeding speed. We simulates to making mathematical correlation using global Kriging interpolation. To find appropriate value of system variables, optimization method is simulation in sequence as following method. First, the optimization solver simulates with DOE (design of experiment) tables to find correlation equation of both system variable and performances. Then, the solver guesses the appropriate values and simulates if the system variables are appropriate or not. If the result of validation doesn't satisfy the convergence and iteration tolerance, the solver makes a new Kriging models and iterates this sequence until satisfy the tolerances.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.10
• /
• pp.4367-4372
• /
• 2014

We here document discovery of expression profile of myeloid derived suppressor cells (MDSCs) in chronic hepatitis B (CHB) patients and changes in the course of disease. The study population was composed of 75 outpatient HBV cases and 15 healthy control cases. Peripheral blood samples were collected for separation of mononuclear cells. Levels of MDSCs labeled with Lin-DR-CD11b+CD33+ obtained from peripheral blood mononuclear cells (PBMC), were revealed to have significant differences between the CHB and other groups. They were 0.414% for health control cases and 0.226% for CHB cases (Z=-2.356, p=0.0189). It also observed that the group of HBeAg positive cases had significant difference in MDSCs/PBMC median ($X^2=11.877$, p=0.003), compared with group of HBeAg negative cases and the healthy control group. It suggested considerable MDSCs might be involved in HBeAg immune tolerance. In addition, negative correlations between MDSCs/PBMC and parameters of ALT, AST and TBil, while positive correlation between MDSCs/PBMC and ALB parameter were found. Multiple comparisons between the four phases and health control phase again, there was a statistically sifnificant difference ($X^2=17.198$, p=0.002). Taken together, these findings may provide a new immunotherapy strategy for reduced the expression levels of MDSCs in CHB patients, through induction of an autoimmune response to virus removal.

• Transactions of Materials Processing
• /
• v.25 no.1
• /
• pp.36-42
• /
• 2016

Fiber metal laminates (FMLs) are well known for improved fatigue strength, better impact resistance, superior damage tolerance and slow crack growth rate compared to traditional metallic materials. However, defects and loss of strength of a composite material can occur due to the vertical load from the punch during the joining with a dissimilar material using a conventional clinching method. In the current study, tapered-hole clinching was an alternative process used to join Al 5052 and FMLs. The tapered hole was formed in the FML before the joining. For the better understanding of static and dynamic characteristics, a clinched joining followed by a tensile-shear test was numerically simulated using the finite element analysis. The design parameters were also evaluated for the geometry of the tapered hole by the Taguchi method in order to improve and compare the lateral joining strength of the clinched joint. The influence of the neck thickness and the undercut were evaluated and the contribution of each design parameter was determined. Then, actual experiments for the joining and tensile-shear test were conducted to verify the results of the numerical simulations. In conclusion, the appropriate combination of the design parameters can improve the joining strength and the cross-sections of the tapered-hole clinched joint formed in the actual experiments were in good agreement with the results of the numerical simulations.

• KSBB Journal
• /
• v.14 no.6
• /
• pp.742-746
• /
• 1999

The microalgal, Chlorella sp. HA-1, had good $CO_2$ fixation efficiency compared to other algal strains at the same operating condition. In this study, Chorella sp. HA-1 showed similar tolerance both 10% and 20% $CO_2$ concentration. By optimization of the major operation variables such as pH, initial cell concentration, light intensity, the $CO_2$ fixation rate could be raised to a reasonably high value, 372 $gCO_2/m^2{\cdot}day$ in a 3 L internally illuminated photobioreactor. In order to maintain the $CO_2$ fixation rate for a long time, the method of semi-continuous operation was employed, in which dilution ratio was the controlling parameter. Starting with the dilution ratio of 0.5 with the increased increment of 0.1, the constant $CO_2$ fixation rate was obtained.

• Journal of Ecology and Environment
• /
• v.38 no.3
• /
• pp.307-318
• /
• 2015

The objectives of this study were to identify multi-level stressors from blood biomarkers to community-level bioindicators and diagnose the stream ecosystem health in polluted streams. Blood chemistry such as total protein ($T_{Pro}$), blood urea nitrogen ($B_{UN}$), total cholesterol ($T_{Cho}$) and $A_{lb}$umin ($A_{lb}$) were analyzed from sentinel fish tissues; the functions of kidney, gill and liver were significantly decreased in the impacted zone ($I_z$), compared to the control zone ($C_z$). Histopathological analysis showed that fish liver tissues were normal in the $C_z$. Fish liver tissues in the $I_z$, however, showed large cell necrosis and degeneration and also had moderate lobular inflammation and inflammatory cell infiltration of lymphocytic histocytes. Species biotic index (SBI) at species level and stream health assessment (SHA) at community level indicated that chemical impacts were evident in the $I_z$ (ecological health; poor - very poor), and this was matched with the blood tissue analysis and histopathological analysis. The impairments of the streams were supported by water chemistry analysis (nitrogen, phosphorus). Tolerance guild analysis and trophic guild analysis of fish were showed significant differences (P < 0.01) between $C_z$ and $I_z$. Overall, multiple parameter analysis from biomarker level (blood tissues) to bioindicator level (community health) showed significantly greater impacts in the $I_z$ than $C_z$. This approach may be effective as a monitoring tool in identifying the multilateral and forthcoming problems related to chemical pollution and habitat degradation of stream ecosystems.