• Journal of Power Electronics
• /
• v.10 no.6
• /
• pp.686-693
• /
• 2010

In this paper, a fault diagnosis method based on fuzzy logic for the three-parallel power converter in a wind turbine system is presented. The method can not only detect both open and short faults but can also identify faulty switching devices without additional voltage sensors or an analysis modeling of the system. The location of a faulty switch can be indicated by six-patterns of a stator current vector and the fault switching device detection is achieved by analyzing the current vector. A fault tolerant algorithm is also presented to maintain proper performance under faulty conditions. The reliability of the proposed fault detection technique has been proven by simulations and experiments with a 10kW simulator.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.412-415
• /
• 2008

In a research on the practical dye-sensitized solar cell, a study on a large module have preference because module must be able to generate the proper current that is possible to convert electrically. So the parallel connection of dye-sensitized solar cells which outputs a large current easily is essential. However, there is a current loss in a paralle connection of dye-sensitized solar cells and the loss becomes larger according to increasing the number of parallel connection. In this study, we analyzed the cause of the current loss in the parallel connection by using the equivalent circuit analysis. One DSC used in this experiment had an active area $8cm^2$(4.62cm$\times$1.73cm) and it attained a conversion efficiency of 5.43% under 1 sun illumination ($P_{in}$ of 100 mW/$cm^2$) using a solar simulator.

• Korean Journal of Optics and Photonics
• /
• v.22 no.2
• /
• pp.83-89
• /
• 2011

In order to improve the calculation speed of an integrating-sphere simulator based on a ray-tracing method, parallel processing with OpenMP directive was implemented into the simulator and the randomness of Monte Carlo method was guaranteed by utilizing a parallel random number generator. It was confirmed that simulation results obtained with more than $10^7$ rays showed good agreement with theoretical results within the error range of 0.5%, and that the calculation speed improved as the number of threads increased. Finally, the spatial response distribution functions of a real integrating sphere were simulated and compared with previous results.

• Journal of Biomedical Engineering Research
• /
• v.35 no.3
• /
• pp.35-41
• /
• 2014

In this study, joint angles of the lower extremity and inertial sensor data such as accelerations and angular velocities were measured during a ski simulator exercise in order to evaluate the skill of skiers. Twenty experts and twenty unskilled skiers were recruited for the study. All expert skiers held the certificates issued by the Korea Ski Instructors Association. A three-dimensional motion capture system and two inertial sensors were used to acquire joint movements, heel acceleration and heel angular velocity during ski simulator exercises. Pattern variation values were calculated to assess the variations in ski simulator motion of expert and unskilled skiers. Integral ratio of roll angular velocity was calculated to determine the parallel alignment of the two feet. Results showed that ski experts showed greater range of motion of joint angle, peak-to-peak amplitude(PPA) of heel acceleration and PPA of heel angular velocity than unskilled skiers. Ski experts showed smaller pattern variations than unskilled skiers. In addition, the integral ratio of roll angular velocity in ski experts was closer to 1. Inertial sensor data measurements during the ski simulator exercises could be useful to evaluate the skill of the skier.

• Journal of the Korea Society for Simulation
• /
• v.22 no.4
• /
• pp.99-107
• /
• 2013

In this study, a conceptual study was performed for the leisure boat simulator used for navigation training. The aim of this work was to secure the basic operational capability of a leisure boat as a simulated driving device for a general novice operator. A leisure boat simulator was designed to support a user more efficiently regarding navigation proficiency and safety training, as well as to minimize the limitation of place and time and it conveniently and cheaply. A cockpit for navigation status display and operational input, 3D visualization graphic device, and parallel display device were designed to give the trainee a maximum sense of reality by applying a motion platform with six degree of freedom, in which disturbance movement such waves, winds, and tide were simulated for the operator. Leisure boat simulator training scenario was developed by analysis of water-related leisure activities act and sea traffic safety act.

• Journal of Satellite, Information and Communications
• /
• v.7 no.2
• /
• pp.80-86
• /
• 2012

The software-based satellite simulator has been developed from the start of the project to resolve the restriction and limitation of using hardware-based software development platform. It enables the development of flight software to be performed continuously since initial phase. The satellite simulator emulates the on-board computer, I/O modules, electronics and payloads, and it can be easily adapted and changed on hardware configuration change. It supports the debugging and test facilities for software engineers to develop flight software. Also the flight software can be loaded without any modification and can be executed as faster than real-time. This paper presents the architecture and design of software-based GEO satellite simulator which has hot-standby redundancy mechanism, and flight software development and test under this environment.

• The Journal of Korean Institute for Practical Engineering Education
• /
• v.3 no.2
• /
• pp.100-105
• /
• 2011

By adopting HIL(Hardware-in-the-Loop), component characteristics in vehicle environment can be obtained without implementing component in the vehicle. In this paper, when specific motor is adopted as traction motor in hybrid electric vehicle HIL implementation procedures are explained. In order to implement HIL method motor testing. vehicle performance simulator and load characteristic are explained. Vehicle controller used in simulator is directly uploaded in real controller. Especially as a load dynamometer actively controlled motor system is used without connecting conventional mechanical inertia. Motor characteristics are obtained using HIL implementation when test motor is used as a traction motor for parallel hybrid electric vehicle. Proposed method can be used as experimental equipment to educate driving characteristics of hybrid electric vehicle.

• Proceedings of the KIEE Conference
• /
• 2006.11a
• /
• pp.198-200
• /
• 2006

This paper presents a development of an educational simulator of particle swarm optimization (PSO) and application for solving the test functions and economic dispatch (ED) problems with nonsmooth cost functions. A particle swarm optimization is one of the most powerful methods for solving global optimization problems. It is a population-based search algorithm and searches in parallel using a group of particles similar to other AI-based heuristic optimization techniques. In developed simulator, lecturers and students can select the functions for simulation and set the parameters that have an influence on PSO performance. To improve searching capability for ED problems, a crossover operation is proposed to the position update of each individual (CR-PSO). To verify the feasibility of CR-PSO method, numerical studies have been performed for two different sample systems. The proposed CR-PSO method outperforms other algorithms in solving ED problems.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.5
• /
• pp.805-813
• /
• 2012

A fan is the most common air flow machinery and is being used in various different industries such as for heavy machinery, home appliances and automobile. An axial fan has blades that force air to move parallel to the shaft about which the blades rotate. This type of fan is used in a wide variety of applications, ranging from small cooling fans for electronics to the giant fans used in wind tunnels. An axial fan generating large air volume used to cool equipments, but is less efficient. A sirocco fan is a efficient device for moving air by centrifugal force and can generate high pressure. Fans that affect the performance and noise of a product are important components. It is also a time and budget consuming equipment to develop a fan through physical experiments. In order to overcome this problem, we have designed and developed a fan simulator for axial and sirocco fan's fluid analysis using supercomputer. Performance and noise prediction based on datamining without numerical analyses is also developed for the conceptual design of a fan.

• ETRI Journal
• /
• v.27 no.4
• /
• pp.427-432
• /
• 2005

In this study, we present a new topology for realizing a grounded inductor employing only a single current conveyor, called a negative-type modified inverting second-generation current conveyor (MICCII-), and a minimum number of passive components, two resistors, and one capacitor. The non-ideality effects of the MICCII- on a simulated inductor are investigated. To demonstrate the performance of the presented inductance simulator, we use it to construct a third order Butterworth high-pass filter and a parallel resonant circuit. Simulation results are given to confirm the theoretical analysis.