• 동력기계공학회지
• /
• 제15권1호
• /
• pp.51-56
• /
• 2011

The various process parameters of thermal spray process affects on quality of Ni-based coatings. Thus, there is need to analyze the effect of process parameters on quality of Ni-based coatings. In this paper, the effects of process parameters on hardness and wear rate of Ni-based coatings were investigated using 4 design of experiments. First, the Ni-based coatings were fabricated according to $L_9(3^4)$ orthogonal array. The hardness tests and the wear tests were performed on the Ni-based coatings. The analysis of variance for the hardness and wear rate were carried out. As a results, the acetylene gas flow and the powder feed rate were identified as main factors effected on the hardness and the oxygen gas flow and the acetylene gas flow were identified as main factors effected on the wear rate. The full factorial experiments design with different levels was applied for investigation of effect of these main factors.

• Journal of the Korean Wood Science and Technology
• /
• 제34권6호
• /
• pp.51-60
• /
• 2006

가래나무 수피를 채취하여 건조시킨 후 분말로 제조하고 3.2 kg을 아세톤-물(7:3, v/v) 혼합용액으로 추출하여 유기용매를 제거한 후 헥산, 메틸렌클로라이드, 에틸아세테이트 및 물을 사용하여 네 개로 분획하고 에틸아세테이트 및 수용성 분획물에 대하여 칼럼 크로마토그래피를 수행하였으며 용리용매로는 메탄올 수용액과 에탄올-헥산 혼합액을 사용하였다. 그 결과 flavanol 화합물인 pinobanksin, taxifolin 및 ampelopsin, flavonol 화합물인 kaempferol, quercetin 및 myricetin 과 flavone glycoside 화합물인 afzelin, astragalin, quercitrin, isoquercitrin 및 myricitrin을 단리하였으며 NMR 및 MS 스펙트럼을 이용하여 구조를 결정하였다.

• 한국재료학회지
• /
• 제28권10호
• /
• pp.551-563
• /
• 2018

Visible and IR windows require a combination of high optical transparency and superior thermal and mechanical properties. Materials, fabrication and characterization of transparent ceramics for visible/IR windows are discussed in this review. The transparent polycrystalline $Y_2O_3$, $Y_2O_3-MgO$ nanocomposites and $MgAl_2O_4$ spinel ceramics are fabricated by advanced ceramic processing and the use of special sintering technologies. Ceramic processing conditions for achieveing fully densified transparent ceramics are strongly dependent on the initial powder characteristics. In addition, appropriate use of sintering technologies, including vacuum sintering, hot-pressing and spark plasama sintering methods, results in outstanding thermal and mechanical properties as well as high optical transparency of the final products. Specifically, the elimination of light scattering factors, including residual pores, second phases and grain boundaries, is a key technique for improving the characteristics of the transparent ceramics. This paper discusses the current research issues related to synthesis methods and sintering processes for yttria-based transparent ceramics and $MgAl_2O_4$ spinel.

• 한국재료학회지
• /
• 제21권2호
• /
• pp.83-88
• /
• 2011

Nano-technology is a super microscopic technology to deal with structures of 100 nm or smaller. This technology also involves the developing of $TiO_2$ materials or $TiO_2$ devices within that size. The aim of the present paper is to synthesize $WO_x$ doped nano-$TiO_2$ by the Sonochemistry method and to evaluate the effect of different percentages (0.5-5 wt%) of tungsten oxide load on $TiO_2$ in methylene blue (MB) elimination. The samples were characterized using such different techniques as X-ray diffraction (XRD), TEM, SEM, and UV-VIS absorption spectra. The photo-catalytic activity of tungsten oxide doped $TiO_2$ was evaluated through the elimination of methylene blue using UV-irradiation (315-400nm). The best result was found with 5 wt% $WO_x$ doped $TiO_2$. It has been confirmed that $WO_x-TiO_2$ could be excited by visible light (E<3.2 eV) and that the recombination rate of electrons/holes in $WO_x-TiO_2$ declined due to the existence of $WO_x$ doped in $TiO_2$.

• Journal of Biosystems Engineering
• /
• 제35권3호
• /
• pp.189-196
• /
• 2010

This study was conducted to develop an non-contact ultrasonic transducer for measurement of fruit firmness. The center frequency of non-contact ultrasonic transducer was 500 kHz. As an active element of non-contact ultrasonic transducer, the 1-3 piezoelectric composite material was selected. That material has high piezoelectric properties such as electro-mechanical coupling factor, $k_t$ and piezoelectric voltage constant, $d_{33}$ and also that material has low acoustical impedance which enables to matching the acoustical impedances between piezoelectric material and air. As a front matching material between 1-3 piezoelectric composite material and air, various kinds of paper with different thickness were tested. To control the dead-zone of the fabricated non-contact ultrasonic transducer, the backing material composed of epoxy resin and tungsten powder were made and evaluated. The fabricated non-contact ultrasonic transducer for fruit showed that the cneter frequency, bandwidth and beamwidth were approximately 480 kHz, 30 % and 12 mm, respectively. It was concluded that non-contact measurement of apple firmness would be possible by using the fabricated non-contact ultrasonic transducer.

• 한국응용과학기술학회지
• /
• 제22권3호
• /
• pp.281-288
• /
• 2005

The silica nanoparticles were used as support of catalyst, filling material, electronic assembler, thin film material, and sensor material. And, the titania nanoparticles were used as pigment, dielectric substance, sensor and photocatalyst. In this paper, the spherical composite particles of $TiO_2/SiO_2$with narrow size distribution and phase pure were synthesized by ultrasonic spray pyrolysis method from $TiOSO_4$ and colloidal silica solution. Using ultrasonic apparatus, this starting solution was vaporized to droplets, and these droplets were induced into tube furnace by carrier gas. The resulting composite powder was characterized by scanning electron microscopy, X-ray diffraction analysis, TG-DTA, in vitro sun protection factor(SPF) and BET surface area analysis.

• 한국전기전자재료학회논문지
• /
• 제30권5호
• /
• pp.318-324
• /
• 2017

Powder compaction technology is widely used to prepare thermal battery components. This method, however, is limited by the size, thickness, and geometry of the battery components. This limitation leads to excessive cell capacity, overweight, and higher cost of the pellets, which decreases the specific capacities and delays the activation time of thermal batteries. $FeS_2$ thin-film cathodes were fabricated by tape-casting technology and analyzed by SEM and EDS in this paper. The residual organic binder of the $FeS_2$ thin-film cathodes decreased with the temperature of the heat treatment, which improved the specific capacity because of the lower resistance. Specific capacities of the $FeS_2$ thin-film cathodes decreased because of the higher residual binder and the restrictive reaction of active materials with molten salts as the thickness increased. $FeS_2$ thin-film cathodes showed much higher specific capacity (1,212.2 As/g) than pellet cathodes (860.7 As/g) at the optimal heat-treatment temperature ($230^{\circ}C$).

• 한국항해학회지
• /
• 제9권2호
• /
• pp.43-63
• /
• 1985

As a circular cylinder has a comparatively simple shape and becomes a basic problem for flows around other various shapes of bodies, the problem of two-dimensional viscous flow around the circular cylinder has been investigated, both theoretically and experimentally. But not a few problems are left unsolved. It is well known that the calculations are successfully made with the approximations of Stokes or Oseen for very low Reynolds numbers, but as Reynolds number is increased, Oseen's approximations as well as Stokes's ones become more and more remote from the exact solution of the Navier-Stokes equations. Therefore, in this paper, the authors transform the Navier-Stokes equations into the finite difference equations in the steady two-dimensional viscous flow at Reynolds number up to 45, and then solve the solution of the Navier-Stokes equations numerically. Also, the authors examine the accuracy of the solution by means of flow visualization with aluminum powder. The main results are as follows; (1) The critical Reynolds number at which twin vortices begin to form in the rear of the circular cylinder is found to be 6 in the experiment and 4 in the numerical solution. (2) As Reynolds number is increased, it is proved that the ratio of the length of the twin vortices to the diameter is grown almost linearly, both experimentally and numerically. (3) Separation angle is also increased according to reynolds number. But it is found that it would converge into 101.3 degrees, both experimentally and numerically.

• 한국전기전자재료학회논문지
• /
• 제25권8호
• /
• pp.651-656
• /
• 2012

A study on capacitive characteristics of stylus pen for touch panel are progressed in this paper. Also the main factors for capacitive sensitivity are studied. Namely, highly sensitive stylus pen which can be applied to capacitive touch panel are studied based on the analysis of materials and process conditions regardless of pattern shapes. Stylus pen was made of PDMS(Poly-Di-Methyl-Siloxane) and conductive metal powders which does not damage the touch panel surface. We tried to get the advantages of both the properties of soft PDMS and conductive metal powders. We found that potential difference of capacitance change with conductivity of the composite materials(PDMS + metal powders) it implies that during touch process, large voltage difference can be caused by the high conductive materials of stylus pen. Stylus pen made by PDMS with mixed with Ag powders which has large conductivity shows more capacitance change of 1 pF than PDMS with other materials of Ni or C powders.

• 동력기계공학회지
• /
• 제12권3호
• /
• pp.55-59
• /
• 2008

In this paper, we have investigated on collection efficiency of fine particle of glass fiber-filter bag according to the surface treatment. The solution consisted of polytetrafluoroethylene(teflon), graphite powder, silicon resin and water was used as a basic surface treatment agent. Tensile strength of glass filter-bag increased with up to 3hrs and then decreased with surface treatment time. Tensile strength and initial modulus of the glass fiber-filter bag treated by iodine after basic surface treatment for 3hrs were lower than those of basic surface treatment for 3hrs, however collection efficiency and fracture strain were higher than those of basic surface treatment for 3hrs. Glass fiber-filter bag with lower initial modulus and more strain will be extend the durable period and the one treated by iodine after basic surface treatment 3or 3hrs is expected high collection efficiency of fine particle. This method makes it possible to manufacture glass fiber-filter bag of the optimum condition.