• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.04b
• /
• pp.7-7
• /
• 2002

Recently social demand to achieve low fuel consumption and clean emission requires the development of new generation vehicle beyond the conventional vehicle concept. In this point, new generation vehicle is newly designed as electric vehicle, hybrid electric vehicle, fuel cell electric vehicle or 3 liter car etc. In order to develop new generation vehicle, it is very important to develop new materials and process technologies now. In this paper these new technologies are presented focusing on weight reduction specially. Steel body can be achieved 20-25% weight reduction by adoption of high strength steel and new process technologies, i.e tailored blank and hydroforming. Aluminium body can be achieved 40-50% weigt down by use of all aluminium monocoque body or aluminium space frame with aluminium panel. Plasitic composite body can be achieved 30% weight reduction comparing with conventional steel body.

• Journal of Powder Materials
• /
• v.15 no.6
• /
• pp.509-513
• /
• 2008

High-pressure abrasive entrained jet have rapidly become important machining technology over the last two decades. However, suspension jet by high-pressure has been recently developed for packaging sawing. Ideally, diamond materials should be used for components in abrasive water-jet systems that are subject to high erosive conditions. Using the diamond orifices improve maintenance and extend wear part life. This paper gives insights to using an abrasive suspension jet with diamond orifice. The influences of orifice material and orifice design are evaluated.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2001.05a
• /
• pp.344-349
• /
• 2001

This paper was to investigate of a adhesiveness for the plasma sprayed coating materials did salt spray by acoustic emission method in tensile loadings. The powders used for the coating were nickel aluminum composite powder Ni-4,5wt.%Al and titanium dioxide powder Ti02. These powders were coated on a carbon steel S45C by plasma spray method. The salt solution was a 5% NaCl and the salt spray times were 2, 5 and 10 hours respectively. The salt solution penetrated into the surface of the substrate through pore of the coating layer built in the process of plasma spay. Corrosion productions formed on the surface of substrate. The adhesiveness between the substrate and the coating layer is weaken by corrosion and the exfoliation initiated chiefly at the corrosion surface of the substrate. The AE events and energy of the corroded coating specimens decreased as the salt spray times increased.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1998.11a
• /
• pp.9-11
• /
• 1998

A phenomenon of electroluminescent radiate as electric field applied in the phosphor, in this paper, we produced the Powder Electroluminescent Device(PELD) which was changing the structure and the thickness of phosphor and insulator for realization of the PELD with high brightness. We made PELD with structure that is WK-1(ITO film/Phosphor/Insulator/Electrode), WK-2(ITO film/Phosphor/Insulator/Electro de), WK-3(ITO film/Phosphor/Insulator/Electrode), WK-4(ITO film/Phosphor+Insulator/ Electrode). The property of the produced PELD are analyzed by measuring the spectrum which electrical and optical property, the brightness and the transferred charge density. In this result, the structure of WK-4 have good luminescence property than others, it's effective thickness is 60${\mu}{\textrm}{m}$. At 100V 400Hz, High brightness of 2700cd/m2 was performed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.10
• /
• pp.865-870
• /
• 2000

In this paper, catalytic combustible gas sensor was fabricated and tested under flammable gases such as CH$_4$and $C_4$H$_{10}$by using Pt coil as a heater and/or temperature sensing element. Fine $Al_2$O$_3$powder was used for a bead and Pt, Pd noble metal powder for a catalyst. Resistance variation of Pt wire was traced by the changes of the gas concentrations in a chamber. Output voltage was then monitored to obtain the gas concentration from the resistance variation. In this experiment, MgO was used to protect cracks in the based and TiO$_2$to increase the sensitivity of the sensors. Water glass was also added to enhance the selectivity to the combustible gases.s.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.286-290
• /
• 1999

Electroluminescence is occurred when phosphor is located in electric field. In this paper, we made powder electroluminescent device (PELD) with structured ITO film/Phosphor/Insulator/Silver paste. The transparent electrode was ITO film and green(2704-01), orange(2702-02) and blue-green(2703-01) were used as phosphor. The insulator was BaTiO$_3$ and $Y_2$O$_3$, back electrode was silver paste. To investigate electrical and optical properties of PELDs, EL spectrum, Brightness, Transferred charge density using Sawyer-Tower\`s circuit was measured.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.367-370
• /
• 1998

In this paper, based on the research of high temperature YBCO superconductor, using the Yb instead of Y, with the YbBCO superconductor powder which was combined by means of conventional solid reaction, textured directional crystal was prepared by MCP method and the character was analyzed. Mixing the starting elements and calcining at 890$^{\circ}C$, 900$^{\circ}C$, 910$^{\circ}C$, single phase YbBCO, Yb$_2$BaCuO$\sub$5/ and BaCuO$\sub$2/ were certified. And from the powder which was calcined at 900$^{\circ}C$ the, sample which became texture-growth by MCP method was well oriented. The result of DTA measurement, the fusing point of YbBCO superconductor and it\`s critical current was measured to be 979$^{\circ}C$, 87K respectively. The critical current density was obtained at the value of 700A/$\textrm{cm}^2$(77K. 0H) calculated by Bean's Model using the measured hysteresis curve of VSM.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1602-1604
• /
• 2000

When insulators are operated near cement factories, some amount of cement powder may be stuck on the surface of insulators and decreases their electrical performances. Three kinds of insulators, such as, silicone EPDM and porcelain insulators, are tested in this paper. Testing Voltage of 25kV is applied to the samples, and surface leakage current is measured for 6 months after cement solvent of 10 vol% was stuck on the surface of each insulator in the laboratory. Insulation layers are cut from 3 and 6 month-aged insulators and tested for ac breakdown, impulse breakdown, contact angle. After aging, electrical properties are unchanged in silicone and EPDM insulators but show some changes in porcelain insulators.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2005.05a
• /
• pp.473-476
• /
• 2005

Today's manufacturing industry is facing challenges from advanced difficult-to-machine materials (WC-Co alloys, ceramics, and composites), stringent design requirements (high precision, complex shapes, and high surface quality), and machining costs. Advanced materials play an increasingly important role in modem manufacturing industries, especially, in aircraft, automobile, tool, die and mold making industries. The greatly-improved thermal, chemical, and mechanical properties of the material (such as improved strength, heat resistance, wear resistance, and corrosion resistance), while having yielded enormous economic benefits to manufacturing industries through improved product performance and product design, are making traditional machining processes unable to machine them or unable to machine them economically. In this paper, mechanical characteristic evaluation test of fine powder type WC-Co alloy was accomplished to obtain clear data for miniaturized special die parts machining with high reliability and high quality.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1998.09a
• /
• pp.35-40
• /
• 1998

There have two kinds of defects, planar defects and vertical defects which were called micropipes in SiC bulk crystals grown by a sublimation method. We could decrease these defects by adding a little piece of Si in the SiC powder or using Ta cylinder in the crucible. so were report the dependence of these defects in a wafer on silicon/carbon ratio in this paper. The chemical species sublimed from SiC powder is affected by carbon from the graphite wall of the crucible. It is important to control the chemical species on the substrate.