• 한국철도학회논문집
• /
• 제10권3호
• /
• pp.251-256
• /
• 2007

The research analyzed dynamo test results to evaluate compatibility between brake disk made of NCM-CV cast iron and various pads. The dynamo test was executed with one kind of resin pad and three kinds of sintered pads suitable for 200 km/h trains according to a program which refers to UIC 541-3. The thermocouples were established in specific location in order to measure the temperature of disk and pads. In addition, the thermal imaging camera was used for capturing the instantaneous thermal characteristic of disk. The research results may be utilized to use as basis data of pad development for NCM-CV brake disk hereafter.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제26회 추계학술대회
• /
• pp.123-128
• /
• 1997

In-situ bearing metal temperature and shaft vibration are measured for an unload type and a preload type, m=0.87, of vertical guide bearing for hydraulic pump-turbines. Guide bearing is a tiltingpad type journal bearing consisting of eight pads whose diameter is 1,450 mm. Rotational speed is 450 rpm. Both the bearing metal temperature and the shaft vibration are very high in the unload type but are slight in the preload type, comparatively. The bearing metal temperature is decreased due to the increase of cooling effect by the increase of preload and the shaft vibration is decreased due to the increase of bearing stiffness. It is concluded that the preload effect of a guide bearing for hydraulic pump-turbines has a large influence on the bearing metal temperature and the shaft vibration.

• Journal of Acupuncture Research
• /
• 제26권2호
• /
• pp.41-48
• /
• 2009

Objectives : The conventional direct and indirect moxibustion therapies for prostate treatment could not been applied to the acupuncture point of $CV_1$(Conception Vessel Meridian 1, 會陰) because of its boring body region. The position of $CV_1$(會陰) is the back side of hard part between the anus and the genital organ. The conventional moxibustion methods have many troubles in operating to the acupuncture point of $CV_1$(會陰). In order to get rid of these problems, we have suggested the special heat generating terminal especially for prostate. The features of the special heat generating terminal for prostate are the low temperature infrared heater and the adhesive moxa-pad. These features are no burnt, no fiery and especially suitable for the point of $CV_1$(會陰). Methods: The heat generating terminal which is a part of the moxa-extract moxibustion cauterizer is composed of a PTC(Positive Temperature Coefficients) ceramic heater and the adhesive moxa-pad We had got the experimental demonstrations by the stimulating the acupuncture points which are $CV_1$(會陰), $BL_{28}$(Bladder Meridian 28, 膀胱兪), and $CV_3$(Conception Vessel Meridian 3, 中極) with the special heat generating terminal for the prostatitis and the benign prosthetic hypertrophy. And the stimulation level was 43$^{\circ}C$ infrared heat for one hour. The type of thermography is IRIS-5000. Results : With one subject suffering the prostatitis and another subject suffering the benign prosthetic hypertrophy, we cauterized the acupuncture points $CV_1$(會陰), $BL_{28}$(膀胱兪) and $CV_3$(中極) with the special heat generating terminal for prostate. We measured the temperature variations by the thermography before and after stimulations. Finally we estimated the tendency of temperature decreasing in the region of post-stroke urinary symptoms and the improvement of nocturnal enuresis after the stimulations. Conclusions : We suggest that the special heat generating terminal of moxa-extract moxibustion cauterizer proposed herein is effective for the treatment of prostate by NIH-CPSI and IPSS.

• 감성과학
• /
• 제18권3호
• /
• pp.93-106
• /
• 2015

최근 고기능성 제품에 대한 수요가 증가함에 따라 ICT 기능과의 융합을 통한 스마트 의류는 일상생활 분야로 확대되고 있다. 그 중 하나로, 발열 텍스타일 및 제어 모듈을 통해 의복 내 발열기능을 조절하는 스마트 의류에 대한 관심이 높아지고 있으며, 발열 기능을 갖는 스마트 의류의 시장 전망이 높아지고 있으나, 발열 패드 부착위치에 따른 발열 기능의 효용성 및 온열감에 대한 연구는 부족한 실정이다. 본 연구에서는 발열 패드의 위치에 따른 피부온의 변화와 온열감에 대한 실증적 연구를 통하여 발열기능의 스마트 의류 개발을 위한 최적의 발열 위치를 도출하고자 하였다. 이를 위하여 20대 표준체형의 남성 10명을 피험자로 선정하였으며, 영하 $5^{\circ}C$의 인공기후실에서 20분의 안정기, 20분의 처치기, 40분의 회복기를 통해 11군데에서의 피부온, 직장온과 주관적 온열감을 측정, 평가하였다. 최종적으로, 발열패드를 위한 최적의 위치를 도출하고 제시하였다.

• 동력기계공학회지
• /
• 제5권3호
• /
• pp.48-55
• /
• 2001

In many applications. rubber components undergo dynamic stresses or deformations of fairly large magnitude. Since rubbers are not fully elastic, a part of the mechanical energy is converted into heat due to the hysteresis loss. Heat generation without adequate heat dissipation leads to heat build up. i. e. internal temperature rise. The purpose of this paper is to predict temperature rise caused by the hysteresis loss, in a rubber pad subjected to complex dynamic deformation. In this unsteady thermal analysis, the temperature distributions of track components are displayed in contour shapes and the temperature variations of some important nodes are represented graphically with respect to the running time of the tank.

• Acute and Critical Care
• /
• 제33권4호
• /
• pp.246-251
• /
• 2018

Background: Target temperature management (TTM) improves neurological outcomes for comatose survivors of out-of-hospital cardiac arrest. We compared the efficacy and safety of a gel pad cooling device (GP) and a water blanket (WB) during TTM. Methods: We performed a retrospective analysis in a single hospital, wherein we measured the time to target temperature ($<34^{\circ}C$) after initiation of cooling to evaluate the effectiveness of the cooling method. The temperature farthest from $33^{\circ}C$ was selected every hour during maintenance. Generalized estimation equation analysis was used to compare the absolute temperature differences from $33^{\circ}C$ during the maintenance period. If the selected temperature was not between $32^{\circ}C$ and $34^{\circ}C$, the hour was considered a deviation from the target. We compared the deviation rates during hypothermia maintenance to evaluate the safety of the different methods. Results: A GP was used for 23 patients among of 53 patients, and a WB was used for the remaining. There was no difference in baseline temperature at the start of cooling between the two patient groups (GP, $35.7^{\circ}C$ vs. WB, $35.6^{\circ}C$; P=0.741). The time to target temperature (134.2 minutes vs. 233.4 minutes, P=0.056) was shorter in the GP patient group. Deviation from maintenance temperature (2.0% vs. 23.7%, P<0.001) occurred significantly more frequently in the WB group. The mean absolute temperature difference from $33^{\circ}C$ during the maintenance period was $0.19^{\circ}C$ (95% confidence interval [CI], $0.17^{\circ}C$ to $0.21^{\circ}C$) in the GP group and $0.76^{\circ}C$ (95% CI, $0.71^{\circ}C$ to $0.80^{\circ}C$) in the WB group. GP significantly decreased this difference by $0.59^{\circ}C$ (95% CI, $0.44^{\circ}C$ to $0.75^{\circ}C$; P<0.001). Conclusions: The GP was superior to the WB for strict temperature control during TTM.

• 생물환경조절학회지
• /
• 제19권4호
• /
• pp.195-202
• /
• 2010

수집 농산물의 세척, 선별, 포장 작업 등이 이루어지는 APC 작업장은 하절기에 작업자들이 고온의 환경에 노출되므로 작업환경 개선을 위한 냉방공조가 요구되고 있다. 기존의 전체 냉방 공조방식은 과도한 유지비로 인한 운용상의 어려움이 발생하고 있으므로 설비비 및 운용비가 상대적으로 저렴한 시스템을 적용할 필요가 있다. 본 연구에서는 하절기 APC 작업공간의 효율적 냉방을 위한 냉방시스템 설계의 기초 연구로써 CFD를 기반으로 하여 양압식 및 음압식 팬 앤 패드 시스템과 국소냉방 시스템에 대해 열유동 수치해석을 수행하여 각각의 냉방효과를 예측하였다. 그 결과, 음압식 팬 앤 패드 시스템은 고온 외기의 과도한 유업으로 인해 패드 하류의 일부 영역을 제외한 대부분의 작업영역에서 상대적으로 고온의 온도 분포를 보였으며 기류의 유속분포 역시 낮게 나타나 APC 냉방시스템으로 부적합한 것으로 판단되었다. 양압식 팬 앤 패드 시스템은 직업장의 중심부 및 각 작업영역에 비교적 균일한 저온환경을 조성하나 작업자 위치별로 기류의 유속편차가 크게 나타났다. 국소냉방 시스템의 경우 각 작업자 위치의 상부에서 냉기류가 공급되는 방식이므로 팬 앤 패드 시스템에 비해 작업자 위치에서의 온도분포와 기류 유속분포가 상대적으로 균일하게 나타났다. 양압식 팬 앤 패드 시스템은 냉방기를 사용하는 기존의 공조방식에 비해 설비비 및 유지비가 저렴하나, 실제 APC 작업장의 냉방공조에 적용시에는 팬 소음, 고습환경이 선별기 등 장비에 미치는 영향, 용수공급 및 패드교체 등을 고려하여 보다 신중한 검토가 요구된다.

• 생물환경조절학회지
• /
• 제25권4호
• /
• pp.288-293
• /
• 2016

본 연구는 복숭아 주간부 동해 예방을 위한 피복재의 보온성을 평가하기 위해 백색부직포, 황색일반지, 방수패드로 만들어진 피복재의 물리적 특성 및 보온성을 평가하고 실제 겨울철 복숭아 주간부 보온효과를 구명하여 피복재로서의 이용가능성을 검토하기 위해 수행하였다. 세 피복재 중 2겹방수패드 처리가 보온율과 열저항성이 가장 우수하였다. 2겹방수패드 처리의 주간단열효과는 $14.09^{\circ}C$ 만큼 온도상승을 차단하였고, 야간보온효과는 $7.23^{\circ}C$ 만큼 온도하강을 차단하여 보온효과가 가장 우수함을 확인하였다. 따라서 방수패드 재질을 보온피복재로 개발 보급할 경우 복숭아 주간부 동해 피해를 경감시키는데 도움을 줄 수 있을 것으로 생각되었다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제31회 춘계학술대회
• /
• pp.166-172
• /
• 2000

Friction characteristics of phenolic resin-based friction composites containing threedifferent relative amounts of graphite and zirconium silicate were investigated by using a pad-on-disk type friction tester. Constant temperature test and constant interval test at three different initial temperatures(100. 200, 300$^{\circ}C$) were performed to examine the effects of friction heat on friction characteristics at elevated temperature. The friction composite(FMO.7) with higher content of ZrSiO$_4$showed unstable friction force at higher temperature and resulted in larger fluctuations of vibration during friction test. The abrasive action of ZrSiO$_4$in friction composite impeded stable transfer film and induced higher friction heat at friction interface. Friction oscillations according to the temperature were associated with the formation of transfer film(i'd body layer) on the friction composite and the counter part.

• 한국자동차공학회논문집
• /
• 제22권5호
• /
• pp.44-49
• /
• 2014

As expansion and contraction of bike disk brake are happened continuously by temperature at repeated urgent braking. In this study, 3 kinds of model are designed according to configurations of holes and thermal durabilities on bike disk brake are investigated by comparing 3 models through temperature and thermal analyses. Maximum thermal stress happened at the disk contacted with pad and the connection part fixing disk rotor. Instead of initial state, the temperature is uniformly distributed at transient state. As the area of hole at disk rotor face becomes wider, thermal stress becomes lower at the initial state. On the other hand, in case the number of holes increases, thermal stress becomes lower at the elapsed time of 100 seconds. The thermal durability of bike disk brake can be improved by applying this study result with configurations of holes.