• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.2
• /
• pp.111-116
• /
• 2010

In this study, the structural analysis was performed to optimize the membrane humidifier with hollow fiber membrane for polymer electrolyte membrane fuel cell system. The main design factors were considered by evaluating the humidifying performance according to various structural parameters such as packing density and length. The effects of operation conditions of membrane humidifier were also elucidated experimentally. Results imply that there are optimum points for the packing density and length of humidifier. It was also found that among operation conditions, relative humidity of wet exhaust gas and temperature of dry inlet gas have major effects on the humidifying performance.

• Steel and Composite Structures
• /
• v.34 no.2
• /
• pp.171-188
• /
• 2020

The past research on cold-formed steel (CFS) flexural members have proved that rectangular hollow flanged sections perform better than conventional I-sections due to their higher torsional rigidity over the later ones. However, CFS members are vulnerable to local buckling, substantially due to their thin-walled features. The use of packing, such as firmly connected timber planks, to the flanges of conventional CFS lipped I-sections can drastically improve their flexural performance as well as structural efficiency. Whilst several CFS composites have been developed so far, only limited packing materials have been tried. This paper presents a series of tests carried out on different rectangular hollow compression flanged sections with innovative packing materials. Four-point flexural tests were carried out to assess the flexural capacity, failure modes and deformed shapes of the CFS composite beam specimens. The geometric imperfections were measured and reported. The North American Specifications and Indian Standard for cold-formed steel structures were used to compare the design strengths of the experimental specimen. The test results indicate clearly that CFS rectangular 'compression' flanged composite beams perform significantly better than the conventional rectangular hollow flanged CFS sections.

• Design & Manufacturing
• /
• v.14 no.4
• /
• pp.25-39
• /
• 2020

In this study, an edge device that monitors the injection molding process by measuring the mold vibration(acceleration) signal and the mold surface temperature was developed and evaluated its performance. During injection molding, signals of the injection start, V/P switchover, and packing end sections were obtained through the measurement of the mold vibration and the injection time and packing time were calculated by using the difference between the times of the sections. Then, the mold closed and mold open signals were obtained using a magnetic hall sensor, and cycle time was calculated by using the time difference between the mold closed time each process. As a result of evaluating the performance by comparing the process data monitored by the edge device with the shot data recorded on the injection molding machine, the cycle time, injection time, and packing time showed very small error of 0.70±0.38%, 1.40±1.17%, and 0.69±0.82%, respectively, and the values close to the actual were monitored and the accuracy and reliability of the edge device were confirmed. In addition, it was confirmed that the mold surface temperature measured by the edge device was similar to the actual mold surface temperature.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.6_3
• /
• pp.1215-1221
• /
• 2023

According to the study and experiments performed on the Improvement of Maintaining Temperature of Aviation Dangerous Goods, a conclusion was drawn that clear technical guidelines should be established from the design and assembly stage of temperature-controlled packaging, taking into account actual transportation environment. In particular, profiles consisting of only two types of summer and winter are difficult to adjust flexibly in transportation process with severe weather and temperature changes such as spring and fall. To this end, there is a need to establish a compromise profile configuration for summer and winter. It was also found that the condition of the refrigerant, temperature control, and the speed of the packaging operation have a significant impact on maintaining constant temperature. Therefore, all packing operations need to be completed within a short period of time in the environment close to the target temperature. The current packing instructions provided by packaging manufacturers do not provide precise instructions on post-conditioning, but the experiments in this study confirmed that post-conditioning is very important for maintaining the target temperature, so it is necessary to provide precise legal packing technical instructions.

• 한국가스학회:학술대회논문집
• /
• 2006.11a
• /
• pp.113-118
• /
• 2006

• Journal of the Korean Institute of Gas
• /
• v.11 no.1 s.34
• /
• pp.23-28
• /
• 2007

This paper presents an experimental investigation on the sealing defects and cracks of O-rings and a valve packing of a gas valve for a LPG cylinder. O-ring in which stops a gas leakage of a liquefied petroleum gas is very important for a LPG valve safety. Valve packing is to open and close a gas flow port for supplying and charging a LPG fuel. The sealing performance of two sealing units ism related to the leak safety and long lift of a gas valve. The investigated results show that most of O-rings was failed due to a circumferential crack in which is caused by partial press bonding failure near the partition zone and an excess compression rate. Some of the O-ring failure was originated by an extrusion of an excessive leak pressure of a LP gas. Thus, this paper strongly recommends a tight quality control and a safety guarantee system of O-rings and valve packing to guarantee a leak safety and to extend a service lift of a gas valve. At the end, a warranty policy of the sealing units should be adopted for increasing a product quality and safety of a gas valve.

• Microbiology and Biotechnology Letters
• /
• v.45 no.4
• /
• pp.322-329
• /
• 2017

Two pilot-scale biocovers (PBCs) were installed in a landfill, and the methane ($CH_4$) concentrations at their inlets and outlets were monitored for 240 days to evaluate the methane removability. Consequently, the packing materials were sampled from the PBCs, and their potential $CH_4$ oxidizing abilities were evaluated in serum vials. The $CH_4$ concentration at the inlet of the biocovers was observed to be in the range of 23.7-47.9% (average = 41.3%, median = 42.6%). In PBC1, where a mixture of soil, earthworm cast, and compost (7:2:1, v/v) was employed as the packing material, the $CH_4$ removal efficiency was evaluated to be between 60.7-85.5%. In PBC2, which was filled with a mixture of soil, earthworm cast, perlite, and compost (4:2:3:1, v/v), the removal efficiency was evaluated to be between 29.2-78.5%. Although the packing materials had an excellent $CH_4$ oxidizing potential (average oxidation rate for $CH_4=180-199{\mu}g\;CH_4{\cdot}g\;packing\;material^{-1}{\cdot}h^{-1}$), $CH_4$ removal efficiency in PBC1 and PBC2 decreased to the range of 0-30% once the packing materials in the PBCs were clogged and channeled. Furthermore, seasonal effects exhibited no significant differences in the $CH_4$ removal efficiency of the biocovers. The results of this study can be used to design and operate real-scale biocovers in landfills to mitigate $CH_4$ buildup.

• Proceedings of the Korean Fiber Society Conference
• /
• 2002.04a
• /
• pp.384-387
• /
• 2002

In the resin transfer molding, there are many advantages such as high volume, high performance, and low cost, The permeability is essential in the design and operation of the process, Traditionally, the determination of permeability can be divided as three methods, which are experimental measurement, analytical, and numerical prediction using the Darcy's law. In this study, the permeability in the microscopic level is first computed on the square-packing and hexagonal packing structures of the filaments inside the yarn by using CVFEM. (omitted)

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.10a
• /
• pp.46-50
• /
• 2001

Due to its ability in producing a net-shape product to high precision in a very shot cycle time, injection molding has become one of the most important polymer-processings in the industry today. Recently the CAE applications in the field of injection molding have provided significant contributions to the mold design and process optimization. As a part of such an application the packing process has been studied using C-PARK. The prediction of pressure variations during post-filling stage for amorphous material has been compared with an experimental observation for a simple rectangular geometry of uniform thickness. And the optimal packing processes were calculated using the cavity pressure curve near the gate. As a case study, a warpage simulation was carried out for a DY-HOLDER with the variable number of gates.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.3
• /
• pp.185-192
• /
• 2004

Vibration table is required to obtain high packing density in expendable pattern casting process. Packing density. which is an important manufacture factor, depends on the vibration pattern induced by vibration table. In general, circular vibration pattern is recognized as the best pattern. The existing vibration table is investigated to identify current vibration pattern and consider a countermeasure. Modal test is utilized to identify the dynamic characteristics of vibration table, and finite element method is used to propose the improved design. In simulation using finite element method, the position of stiffeners is obtained to satisfy the required dynamic characteristics.