• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1131-1134
• /
• 2003

Unknown parameters of a nonlinear system were estimated using a signal compression method. The estimated parameters were natural frequency and tile damping coefficient. This study applied a algorithm using tile comparison of the cross-correlation coefficient between the impulse response from a model and it from the signal compression method. The impulse through linear element included in a nonlinear system could be obtained by the signal compression method. The unknown parameters of the linear element could be estimated by comparing the Bode plots of system's impulse response with them of model's response. In this study, a LSCM(LabVIEW-Signal-Compression-Method) was developed to identify a nonlinear system. The LSCM consisted of National Instrument's (NI) Data Acquisition (DAQ) Board (Model PCI-1200), a monitoring program using LabVIEW software package, DAQ Signal Accessory Board, and 2nd-order electric circuits. The designed electric circuits consisted of resistors, inductors and capacitors. To evaluate the performance of the LSCM, the response from model with known parameters is compared with the response from the real system using the monitoring program. The results from simulation of experiment showed that the developed LSCM provided a reliable estimation performance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.2
• /
• pp.111-119
• /
• 2017

This paper presents a method to determine the rear steering angle in integrated chassis control with electronic stability control (ESC) and rear wheel steering (RWS). A control yaw moment needed to stabilize a vehicle should be distributed into the tire forces generated by the ESC and RWS. Weighted pseudo-inverse control allocation (WPCA) is adopted to determine the tire forces. Four methods are proposed to calculate the rear wheel steering angle. To validate the proposed methods, a simulation is performed using a vehicle simulation software package, CarSim. The simulation results show that the proposed method for determining the rear wheel steering angle improves the performance of the integrated chassis control.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.11
• /
• pp.1069-1076
• /
• 2007

The purpose of this study is to improve the performance of a linear feeder that can transport grains uniformly. In order to analyze the dynamic behaviors of a linear feeder, the displacements of the feeder are measured by several accelerometers when it is in an operating condition. After the signal data from the accelerometers are captured in the time domain, the feeder motion in the space is visualized by using graphic computer software. In addition, a dynamic model of the feeder is established for a multi-body dynamics simulation. For the dynamic simulation, RecurDyn, which is a commercial multi-body dynamic package, is used. From the experimental and the computational approaches, an optimal dynamic motion is obtained for uniform transportation of grains. Furthermore, we also consider the determination of design parameters for optimal dynamic motion such as centroid, stiffness, and damping coefficient of the feeder system.

• Steel and Composite Structures
• /
• v.16 no.4
• /
• pp.437-454
• /
• 2014

The influence of spacers on the behaviour and ultimate capacity of intermediate length CFS open section columns under axial compression is investigated in this paper. The focus of the research lies in the cross- section predominantly, failed by distortional buckling. This paper made an attempt to either delay or eliminate the distortional buckling mode by the introduction of transverse elements referred herein as spacers. The cross-sections investigated have been selected by performing the elastic buckling analysis using CUFSM software. The test program considered three different columns having slenderness ratios of 35, 50 & 60. The test program consisted of 14 pure axial compression tests under hinged-hinged end condition. Models have been analysed using finite element simulations and the obtained results are compared with the experimental tests. The finite element package ABAQUS has been used to carry out non-linear analyses of the columns. The finite element model incorporates material, geometric non-linearities and initial geometric imperfection of the specimens. The work involves a wide parametric study in the column with spacers of varying depth and number of spacers. The results obtained from the study shows that the depth and number of spacers have significant influence on the behaviour and strength of the columns. Based on the nonlinear regression analysis the design equation is proposed for the selected section.

• Ocean Systems Engineering
• /
• v.3 no.2
• /
• pp.137-147
• /
• 2013

Moonpools are vertical wells in a floating body used onboard many types of vessels like cable-laying vessels and offshore support vessels. Moonpool gives passage to underwater activities for different types of ships as per their mission requirements. It is observed that inside a moonpool considerable relative motions may occur, depending on shape, depth of the moonpool and on the frequency range of the waves to which the ship is exposed. The vessel responses are entirely different in zero and non-zero Froude number. Former situation is paid attention in this study as the mission requirement of the platform is to be in the particular location for long period of operation. It is well known that there are two modes of responses depending on the shape of the moonpool viz., piston mode for square shape and sloshing mode for rectangular shapes with different aspect ratios of opening like 1:1.5 and 1:2 ratios. Circular shaped moonpool is also tested for measuring the responses. The vessel moored using heavy lines are modeled and tested in the wave basin. The moored lines are provided with pre-tension and the dynamic tensions on the lines are measured. The different modes of oscillations of water column are measured using wave gauge and the vessel response at a particular situation is determined. RAOs determined for various situations provide better insight to the designer. The experiments done in the wave basin may also be compared with a software package meant for handling moored floating bodies.

• Advances in nano research
• /
• v.9 no.4
• /
• pp.251-261
• /
• 2020

In this article, vibration attributes of single walled carbon nanotubes based on Galerkin's method have been investigated. The influence of power law index subjected to different end supports has been overtly examined. Application of the Hamilton's variational principal leads to the formation of partial differential equations. The effects of different physical and material parameters on the fundamental frequencies are investigated for armchair and zigzag carbon nanotubes with clamped-clamped, simply supported and clamped-free boundary conditions. By using volume fraction for power law index, the fundamental natural frequency spectra for two forms of Single-Walled Carbon Nanotubes (SWCNTs) are calculated. The influence of frequencies against length-to-diameter ratios with varying power law index are investigated in detail for these tubes. MATLAB software package has been utilized for extracting tube frequency spectra. The obtained results are confirmed by comparing with available literature.

• Korean Journal of Adult Nursing
• /
• v.16 no.2
• /
• pp.276-287
• /
• 2004

Purpose: This study was undertaken to investigate the effects of foot reflexo-massage on physical, psychological, and physiological parameters in patients with osteoarthritis of the knee. Method: This study was employed non-equivalent control group pretest-posttest time series experimental design. The subjects of this study were 47 elderly patients with osteoarthritis of the knee from two different nursing homes in Deajeon. The patients were divided into two groups; 26 patients in experimental group, the rest in control group. Each patient in experimental group received the 30-minute foot reflexo-massage, 3 times per week for 4 weeks. The dependent variables of each patient were measured before treatment, after 2 weeks and after 4 weeks during the treatment session. The collected data was analyzed using the Social Package Social Science(version 10.0) software program. Result: There were significant differences in the flexion angle of both knees; the flexion and extension muscle strength of both knees; systolic blood pressure; POMS; plantaris skin temperature and blood velocity of dorsalis pedis artery between the two groups over different the three measurement times. Conclusion: The results suggest that foot reflexo-massage could be an effective intervention to improve physical, psychological and physiological parameters for patients with knee osteoarthritis.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.12
• /
• pp.5028-5057
• /
• 2015

In this paper, a new mathematical scheme of Macro Handover Management (MHM) in F-HMIPv6 networks based on Location Based Services (LBS) is proposed. Previous schemes based on F-HMIPv6 protocol usually suffer from three major drawbacks: First, They don't exploit the information about the user mobility behavior in order to reduce handover effects. Second, they only focus on the micro mobility level. Third, they don't consider the quality of service (QoS) of the traffic. The proposed MHM scheme avoids these drawbacks using the available information about Mobile Node (MN) such as user mobility patterns and MN's velocity to predict handover and improve network's QoS. It also takes the traffic type in consideration since it presents a major factor in locating QoS for the user. MHM is analyzed and compared with the F-HMIPv6. The results show that MHM improves the performance in terms of packet delivery cost, location update cost, and handover latency. The design of MHM comprises software package in the MN in addition to a hardware part in the network side. It has implications for communication, design, and pricing of mobile services.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.5
• /
• pp.526-531
• /
• 2001

The flow of remote field eddy current energy is studied at nonmagnetic coaxial tubes by using both experiments and finite element calculations based on commercial software package. The results showed that remote field eddy current energy at coaxial tubes flow along over the outer surface of external tube, not through the gap between internal and external tubes. This means that the through wall transmission characteristic of remote field eddy current testing (RFECT) is still valid at tube in tube configurations and the RFECT could be potential nondestructive technique for crack detection, spacer location and gap sizing at the coaxial CANDU fuel channel tubes.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.8
• /
• pp.21-29
• /
• 2003

This paper describes a research work on the development of computer-aided design system for deep drawing & ironing of a high pressure vessel. An approach to the system is based on the knowledge-based rules. Knowledge for the system is formulated from plasticity theories, handbook, experimental results and empirical knowledge of field experts. An attempt is made to link programs incorporating a number of expert design rules with the process variables obtained by commercial FEM software, DEFORM and ANSYS, to form a useful package. It is composed of five main modules, which are calculation of product thickness, input, production feasibility check, process planning, and autofrettage process modules and two submodules, which are folding check and process variable verification submodules. Programs for the system have been written in AutoLISP on the AutoCAD 2000 using personal computer. The developed system makes it possible to design and manufacture large high pressure vessel requiring D.D.I. process more efficiently.