• Proceedings of the KIPE Conference
• /
• 1996.06a
• /
• pp.109-112
• /
• 1996

In this paper, we composed utility interactive photovoltaic generation system of current source inverter, and controlled that low harmonic and high power factor are hold by supposing control and compensation method which is concerned with synchronous signal distortion and modulation delay. And we put parallel resonant circuit into dc link, so, magnitude of direct reactance was reduce by restraining direct current pulsation which had accumulation of pulsating power in alternating electrolytic condenser. Also we controlled that modulation factor is operated around maximum output of solar cell.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.101-110
• /
• 1997

The circuit effects due to the transformer primary side series equivalent inductance in the Zero Voltage Switching Pulse Width Modulated Half Bridge DC/DC Converter and its impact on the effective duty are analyzed. The steady state equations and the small signal model of the converter are derived incorporating the effects of the complementary control and the utilization of transformer primary side series equivalent inductance. The open plant dynamics are analyzed on the basis of the model derived. The model predictions are confirmed by experimental measurements.

• Journal of Advanced Marine Engineering and Technology
• /
• v.19 no.1
• /
• pp.71-81
• /
• 1995

In this paper, a new speed control scheme for induction motor drives that regular sampled PWM and harmonic elimination switching pattern over the full range of output speed is presented. The proposed scheme(hybrid scheme) provides three mode and guarantees smooth voltage boost. A detailed description of the scheme, along with the relalization aspect, is described. Moreover, methods of compensating for dead time and optical transmission system of drive signal are proposed and investigated. Finally, experimental investigation of hybrid scheme is presented.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.5
• /
• pp.501-507
• /
• 2005

This paper proposes a Hybrid Random PWM(HRPWM) technique using a LF2407 DSP board in order to spread the power spectra of an induction motor. The proposed method is composed to the PRBS (Pseudo-Random Binary Sequence) with the Lead-Lag random bit and the random triangular carrier for the logical comparison. Also, a DSP generates the random number, the PRBS and the three-phase reference signal, a MAX038 chip operating as frequency modulator generates the random triangular carrier. For verification of the proposed method, the experiments were conducted with a three-phase adjustable speed a.c drives, and the results of simulations and experiments are presented.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.89-95
• /
• 2014

An LED lighting which adjusted brightness according to the surround ambient implemented using PWM technology and power devices. To measure the brightness of surround ambient a CdS sensor was used. A control board for the generation of the PWM signal was made using a MCU and duty ratio was controlled according to light intensity of surround ambient of the system. To drive the LED lamps which require high-voltage and high-current power devices were used for switching the DC power supply. Measurement results show that the IGBT is excellent as only lineality but the PowerBJT is more good to consider to efficiency and cost.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.4
• /
• pp.376-382
• /
• 2014

This paper proposes the pulse width modulation (PWM) control strategy for low-speed operation in the three-level neutral-point-clamped (NPC) inverters based on the bootstrap gate drive circuit. As a purpose of the cost reduction, several papers have paid attention to the bootstrap circuit applied to the three-level NPC inverter. However, the bootstrap gate driver IC cannot generate the gate signal to the IGBT for low-speed operation, because the bootstrap capacitor voltage decreases under the threshold level. For low-speed operation, the dipolar and partial-dipolar modulations can be the effective solution. However, these modulations have drawbacks in terms of the switching loss and THD. Therefore, this paper proposes the PWM control strategy to operate the inverter at low-speed and to minimize the switching loss and harmonics. The experimental results are presented to verify the validity on the proposed method.

• Proceedings of the KIEE Conference
• /
• 2003.11b
• /
• pp.235-238
• /
• 2003

In this study, we propose a method of digital control to drive the vibrating gyroscope using electromagnetic-force. The gyroscope requires accurate vibration control and signal processing for high performance. Conventional PLL based analog controller is not only difficult to manufacture but also weak to outer environment such as temperatures, air pressures and etc. But digital controller using DSP can consistently maintain the cylinder vibration and perform digital signal processing regardless of disturbance. DSP's PWM function was utilized to control the vibration, and rotation-detecting algorithm was developed. Finally, the controller was verified by simulation and experiment using rotation-rate table.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.524-526
• /
• 2011

This paper focuses on study on PWM converter control under unbalanced network condition. Voltage unbalance in a three-phase system causes the performance deterioration by producing 120 Hz voltage ripples in the DC link and 120 Hz ripple in reactive power. To eliminate the ripples, both positive and negative sequence currents should be controlled simultaneously. In this paper four PI controllers on synchronous reference frame is implemented to control D and Q currents in both positive and negative sequence. Positive and negative sequence signal extraction is done using delay signal cancellation method. Simulation results show satisfactory performance in suppressing 120 Hz ripples.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.8
• /
• pp.155-160
• /
• 2002

In this paper, a controller design for brushless linear motor is implemented. The designed controller is mainly composed of current, speed and position controller, which are carried out by the high-speed digital signal processor (DSP). In addition the PWM inverter is controlled by space voltage PWM method. This system is implemented by using 32-bit DSP (TMS320C31), a high-integrated logic device (EPM7192), and IPM (Intelligent Power Module) for compact and powerful system design. The experimental results show the effective performance of controller for the brushless linear motor.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.2
• /
• pp.137-142
• /
• 2003

Two existing continuous-time models for the current-mode control have presented noticeable differences in their small-signal predictions. As an attempt to clarify the origin of these disparities, this paper presents an alternative way of deriving a continuous-time model for the current-model control. The results of this paper would provide insights to comprehend the dissimilarity in the modeling method and final results of the earlier models of current-mode control models.