• Polymer(Korea)
• /
• v.31 no.3
• /
• pp.221-227
• /
• 2007

The mechanical properties and morphologies of lyocell and its blend we compared. Poly (vinyl alcohol) (PVA) was used as a filler in blends with lyocell produced through solution blending. The variations of their properties with polymer matrix filler content are discussed. The ultimate tensile strength of the PVA/lyocell blend is highest for a blend lyocell content of 30 wt%, and decreases as the lyocell content is increased up to 40 wt%. The variations in the initial moduli of the blends with filler content are similar. Lyocell and its blended hybrid films were prepared by the solution intercalation method, using dodecyltriphenylphosphonium-mica ($C_{12}PPh$-Mica) as the organoclay. The variations of the mechanical tensile properties of the hybrids with the organoclay content were examined. These properties were found to be optimal for an organoclay content of up to 5 wt%. However, the mechanical tensile properties of the PVA/Lyocell (w/w=30/70) blended hybrid films were found to decrease linearly with increases in organoclay content from 1 to 5 wt%.

• Journal of Information Display
• /
• v.6 no.2
• /
• pp.16-18
• /
• 2005

Hybrid insulator pentacene thin film transistors (TFTs) are fabricated with thermally grown oxide and cross-linked polyvinylalcohol (PVA) including surface treatment by dilute ploymethylmethacrylate (PMMA) layer on $n^+$ doped silicon wafer. Through the optimization of $SiO_2$ layer thickness in hybrid insulator structure, carrier mobility is increased to more than 35 times than that of the TFT which has only a gate insulator of $SiO_2$ at the same electric field. The carrier mobility of $1.80cm^2$/V-s, subthreshold swing of 1.81 V/decade, and $I_{on}/I_{off}$ current ratio> $1.10{\times}10^5$ are obtained less than -30 V bias condition. The result is one of the best reported performances of pentacene TFTs with hybrid insulator including cross-linked PVA layer as a gate insulator at relatively low voltage operation.

• Membrane and Water Treatment
• /
• v.3 no.3
• /
• pp.169-179
• /
• 2012

One of the major limitations in the use of commercial aromatic polyamide thin film composite (TFC) reverse osmosis (RO) membranes is to maintain high performance over a long period of operation, due to the sensitivity of polyamide (PA) skin layer to oxidizing agents, such as chlorine, even at very low concentrations in feed water. This article reports surface modification of a commercial TFC RO membrane (BW30-Dow Filmtec) by covering it with a thin film of poly(vinyl alcohol) (PVA) crosslinked with glutaraldehyde (GA) to improve its resistance to chlorine. Crosslinking reaction was carried out at 25 and $40^{\circ}C$ by using PVA 1.0 wt.% solutions at different GA/PVA mass ratio, namely 0.0022, 0.0043 and 0.013. Water swelling measurements indicated a maximum crosslinking density for PVA films prepared at $40^{\circ}C$ and GA/PVA 0.0043. ATR-FTIR and TGA analysis confirmed the reaction between GA and PVA. SEM images of the original and modified membranes were used to evaluate the surface coating. Chlorine resistance of original and modified membranes was evaluated by exposing it to an oxidant solution (NaClO 300 mg/L, NaCl 2,000 mg/L, pH 9.5) and measuring water permeability and salt rejection during more than 100 h period. The surface modification effectively was demonstrated by increasing the chlorine resistance of PA commercial membrane from 1,000 ppm.h to more than 15.000 ppm.h.

• Journal of Radiation Protection and Research
• /
• v.10 no.1
• /
• pp.64-66
• /
• 1985

A methylene blue-PVA system has been tested as a krad range dosimeter. Mb dye films were fabricated by casting PVA in solution with the methylene blue. In the air the system was irradiated by X-ray and the decolorisation of the dye film was found to remain unchanged for sufficiently long time. The radiation response on optical density at 670 nm in the Mb-PVA system shows a quite good linearity and reproducibility in the krad range.

• Macromolecular Research
• /
• v.17 no.8
• /
• pp.591-596
• /
• 2009

To trace the plasticizing effects of propylene glycol (PG) on poly(vinyl alcohol) (PVA), the rheological properties of PVA solutions in dimethyl sulfoxide (DMSO) and the physical properties of PVA films were discussed in terms of PG content. Both properties were closely related to the hydrogen bond breaking effects of PG The 6 and 12 wt% PVA solutions containing PG exhibited Bingham behavior, which was more noticeable at lower plasticizer content and higher polymer concentration. The 6 wt% PVA solutions containing more than 30 wt% PG showed a sudden decrease of viscosity over the frequency range of 0.08 and 0.2 rad/s. However, the 12 wt% PYA solutions showed no viscosity reduction even at a PG content up to 40 wt%. The glass transition temperature of the PVA/PG films was almost linearly decreased with increasing PG content but an abrupt reduction was observed at a plasticizer content 30 wt%, suggesting that the hydrogen bond breaking effects of PG on PVA became dominant between 20 and 30 wt%. This effect was further supported by the similar tendency of the tensile properties.

• Elastomers and Composites
• /
• v.41 no.1
• /
• pp.3-9
• /
• 2006

Optimal conditions for preparation of starch/PVA blends were investigated with the consideration of factors that may influence mechanical properties of the blends. Multiplex mixture optimal method as a statistical method were performed and then tensile strength, strain at break, Young's modulus and tear strength of films of the blends were measured to determine the optimal conditions for preparation. The mechanical properties needed for the degradable agricultural mulch were the target of this experiment. Results showed that although the strain at break was a little insufficient, the other properties were very close to the target. This means that the mechanical properties of the film from this blend as a whole are very compatible with those of the reference mulch.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.23 no.1
• /
• pp.9-15
• /
• 2017

To identify applicability for packaging material of polyvinyl alcohol (PVA)/boric acid (BA) coating solution with highly-enhanced water vapor and oxygen barrier properties, the PET/PVA-BA/OPP multi-layer films were prepared through comma coating and lamination process. The oxygen and water vapor permeabilities, and tensile strength of as-prepared multi-layer films were investigated before and after pressure cooker test (PCT). Although oxygen and water vapor permeabilites, and mechanical properties of PET/PVA-BA/OPP multi-layer films was decreased after PCT, their properties were highly enhanced as increase of BA contents in PVA matrix. This is strongly related with enhanced cross-linking density in PVA-BA layer. In storage test of seasoned-laver, the PET/PVA-BA/OPP multi-layer films were comparatively effective to suppress the increase in peroxide value originating from oxidation of seasoned-laver. Comparing the commercially available PP/Al-metallized PP for seasoned-laver packaging, however, PET/PVA-BA/OPP multi-layer films did not show any advantage in water activity. This is due to higher water vapor permeation properties of as-prepared multi-layer films. Therefore, further studies are required to enhance the water vapor permeation in PET/PVA-BA/OPP multi-layer films.

• Polymer(Korea)
• /
• v.30 no.6
• /
• pp.545-549
• /
• 2006

Blends of poly(acrylic acid- co-maleic acid) (PAM) with poly (vinyl alcohol) (PVA) were pre -pared in distilled water PVA/PAM/saponite (PVA/PAM/SPT) nanocomposite films were prepared with various clay contents by using the solution intercalation method. The variations of the dispersion, morphology, and thermo-mechanical properties of the nanocomposites with clay content in the range 0 to 9 wt% were examined. Up to 3 wt% clay loading, the clay particles were homogeneously dispersed in the PVA/PAM blends. However, some agglomerated structures form in the polymer matrix above a clay content of 7 wt%. The thermal stability of the hybrids was increased linearly with increasing the clay loading up to 9 wt%. The maximum strength and modulus were obtained at a clay content of 7 wt%. Thus, the addition of small amounts of clay to the PVA/PAM blends produced PVA/PAM nano-composites with improved the thermo-mechanical properties.

• Polymer(Korea)
• /
• v.27 no.5
• /
• pp.405-412
• /
• 2003

Poly(vinyl alcohol) (PVA) and N-(2-hydroxy)propyl-3-trimethylammonium chitosan chloride (HTCC), a water soluble chitosan derivative synthesized by the reaction of quaternary ammonium compound with chitosan, were blended using water as a solvent and the PVA/HTCC blend films with various compositions were prepared by solution casting method. The miscibility between the two polymers and the thermal properties of the blend films were investigated using FT-IR, DSC, DMA, and TGA. Single glass transition temperatures and single melting temperatures of the blend films along with the strong and clear film state for the whole composition of blending ratios suggest the miscibility between PVA and HTCC. The PVA/HTCC blend films with HTCC content of 1% and greater showed excellent antimicrobial activity.

• Textile Coloration and Finishing
• /
• v.18 no.6 s.91
• /
• pp.49-56
• /
• 2006

Surface treatment using UV irradiation was carried out to improve optical properties of polarizing films. The effects of UV energy of the UV-treated PVA films were investigated by measuring reflectance, surface roughness, contact angles, ESCA, and ATR. Reflectance decreased at wavelength of 450 nm or less and surface roughness increased with increasing UV energy. Water contact angle increased in the irradiated PVA films and surface energy decreased with increase in w energy. An analysis showed that the OH groups were broken and some new groups were introduced such as C=C and C=O bonds together with increased $O_{1s}/C_{1s}$, resulting in the observed surface modification effect. Surface modified PVA polarizing films showed improvement in light transmittance of polarizing films at high wavelength region without deteriorating polarization efficiency, which was not affected by UV irradiation sequence during manufacturing processes such as coloring and drawing.