• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.9
• /
• pp.1602-1608
• /
• 2007

The composites were fabricated, respectively, using 61[vol.%] SiC-39[vol.%] $TiB_2$ and using 61[vol.%] SiC-39[vol.%] $ZrB_2$ powders with the liquid forming additives of 12[wt%] $Al_2O_3+Y_2O_3$ by hot pressing annealing at $1650[^{\circ}C]$ for 4 hours. Reactions between SiC and transition metal $TiB_2$, $ZrB_2$ were not observed in this microstructure. The result of phase analysis of composites by XRD revealed SiC(6H, 3C), $TiB_2$, $ZrB_2$ and $YAG(Al_5Y_3O_{12})$ crystal phase on the Liquid-Phase-Sintered(LPS) $SiC-TiB_2$, and $SiC-ZrB_2$ composite. $\beta\rightarrow\alpha-SiC$ phase transformation was occurred on the $SiC-TiB_2$ and $SiC-ZrB_2$ composite. The relative density, the flexural strength and Young's modulus showed the highest value of 98.57[%], 249.42[MPa] and 91.64[GPa] in $SiC-ZrB_2$ composite at room temperature respectively. The electrical resistivity showed the lowest value of $7.96{\times}10^{-4}[\Omega{\cdot}cm]$ for $SiC-ZrB_2$ composite at $25[^{\circ}C]$. The electrical resistivity of the $SiC-TiB_2$ and $SiC-ZrB_2$ composite was all positive temperature coefficient resistance (PTCR) in the temperature ranges from $25[^{\circ}C]$ to $700[^{\circ}C]$. The resistance temperature coefficient of composite showed the lowest value of $1.319\times10^{-3}/[^{\circ}C]$ for $SiC-ZrB_2$ composite in the temperature ranges from $100[^{\circ}C]$ to $300[^{\circ}C]$ Compositional design and optimization of processing parameters are key factors for controlling and improving the properties of SiC-based electroconductive ceramic composites.

• Journal of the Korean Geosynthetics Society
• /
• v.17 no.1
• /
• pp.127-137
• /
• 2018

Gravel Compaction Pile (hereinafter referred to as GCP) is a ground improvement technique by packing crushed stones on fragile clay ground, pressing it, and forming stakes on the foundation. Although many researchers have analyzed stress behavior of GCP composite ground on domestic GCP technique using laboratory experiment and field experiment, analyses of stress behavior according to the difference of stiffness of mat foundation loaded on the upper foundation of GCP composite ground have not been done actively. Therefore, this study aimed to identify the stress concentration ratio in accordance with the difference of basis stiffness by interpreting figures. To perform this, replacement ratio was changed and modelled using ABAQUS, software for finite element analysis and analyzed the stress concentration ratio, amounts of settlement, and maximum amounts of horizontal displacement of composite ground in accordance with the difference of stiffness. An analysis showed that the stress concentration ratio of rigid foundation was highly assessed than unloading of flexible foundation in case of unloading, while amounts of settlement under flexible unloading condition were slightly higher than under rigid condition. This indicates that the characteristic of stress behavior on the different stiffness of upper foundation needs to be clarified. In addition, the maximum horizontal displacement was generated in a constant level regardless of the difference of stiffness.

• Journal of Technologic Dentistry
• /
• v.35 no.3
• /
• pp.243-257
• /
• 2013

Purpose: This study aims to analyze the factors affecting the dropout intentions of the dental technology students of a college. Methods: The subject of this study was 76 freshmen and 74 sophomores of dental technician major in an anonymous college. Results from the questionnaire called K-vision diagnosis program were computed by means of t-test, One-Way ANOVA, and correlation analysis. Results: 1. Total points of the drop out intention came to 782.14 points. Of the five categories concerned with the drop out intention, complain in college satisfaction(50.12points) was the highest and department satisfaction(47.51points) was the lowest. Of 16 subcategories, complaining in administrative supporting system proved the highest as 50.80 points and Inquiry to Professor the lowest(45.56 points). 2. Among the general characteristic gender (p<. 01), student group (p<.01), and credit (p<.05) made a meaningful statistical difference; no statistical significance was found in grade, admission, and dwellings. 3. Of the five categories, statistical significance was shown as follows; Department satisfaction (p<.01), College satisfaction (p<.05) under gender, Department satisfaction (p<.05) in grade, Academic integration (p<.01), Department satisfaction (p<.01) in credit. No statistical meaning was found in admission and dwellings. 4. Statistical significance was found under 16 subcategories as follows: Career identification(p<.01), Academic support system(p<.01), Social activity II(p<.05) in gender area, Inquiry to professor(p<.01), Learning(p<.05), Understanding learning I(p<.05) in grade area, Learning(p<.001), Career identification(p<.001), Understanding learning I(p<.01), Understanding learning II(p<.01), Inquiry to professor (p<.01), Learning ability (p<.05), Occupation (p<.05), Social Activity II(p<.05), Administrative support system (p<.05) in student group area, Credit (p<.001), Career identification (p<.01), Understanding learning I(p<.05) in credit area; admission and dwellings was statistically meaningless. 5. Of the 5 categories academic integration (r=.766) was most relevant to the dropout intention of the subjects and followed by department satisfaction (r=.735), college satisfaction (r=.554), service acceptability (r=.373), and statistical significance was shown as p<.01. Conclusion: Considering the results of this study, we are in a pressing need for the introduction of policies and programmes aiming at preventing the dropout rates of the dental technician majors at college. In tandem with this, qualitative and viable human resource management of the dental technicians should be implemented.

• Journal of the Korean Society of Costume
• /
• v.58 no.8
• /
• pp.30-46
• /
• 2008

This study aims to develop an academic costume design representing the university identity of Seoul Women's University. As a formal dress and uniform symbolizing the dignity of study, academic costume arouses self-esteem of the owner and represents the symbolic order. UI(University Identity) is a system that embodies the identity of the university and create a certain image, and thus actively delivers the image pursued by the university. The study method to develop a new academic costume design of Seoul Women's University includes the theoretical background of UI and academic costume, investigation on the current rendition of academic costume, home and abroad, and a survey to collect the basic data for academic costume design development. Most of the respondents presented negative opinions on the existing academic costume and graduation cap, which do not show any clear distinction from those of other universities. They made a pressing demand for the development of an academic costume that well represents the image of the university by reflecting the university feature and symbol. As a result of the survey, it turned out that they preferred an academic costume with short length balloon sleeves to the exiting one, and that as for neck line and front hook, those of the existing one were preferred. This study developed and presented 9 different models of graduation gowns and 5 different caps based on the theoretical investigation and survey concerning academic costume. It is expected that the academic costume representing the university identity not only arouses self-esteem of the owner, but also enhances the university's position.

• Composites Research
• /
• v.33 no.5
• /
• pp.235-240
• /
• 2020

In this study, in order to improve the impact resistance of the B₄C tile-inserted B₄C_p/Al7075 hybrid composite, a control method of the B₄C/Al7075 interface was developed and the characteristics of the controlled interface were analyzed. B₂O₃, Ni, and Si were coated on the B₄C tile surface using additional thermal oxidation, electroless plating, and plasma spraying. The coated B₄C tile is inserted into the B₄C_p/Al7075 composite material using the liquid pressurization method. Interfacial energy, bonding strength, and impact resistance were measured to analyze the effect of the coating. All coatings enhanced interfacial energy, bonding strength, and impact resistance, and in particular, it was confirmed that the impact resistance increased by 86.8% when B₂O₃ coating was used. This study is significant in developing and analyzing a core surface treatment method that improves the performance of B₄C/Al series composites, which are attracting attention as next-generation lightweight amour and bulletproof materials.

• Economic and Environmental Geology
• /
• v.37 no.6 s.169
• /
• pp.603-612
• /
• 2004

Pyrochlore is known as one of the most promising materials for the immobilization of radionuclide in high level waste. This study included the synthesis, phase relation and characteristics of $pyrochlore(CaCeZr_xTi_{2-x}O_{7,\;x=0.2\~2.0)$ in the system of Ca-Ce-Zr-Ti-O. Using the CPS(Cold pressing and sintering) method, the mixtures of $CaCO3_,\;CeO_2,\;ZrO_2\;and\;TiO_2$ oxides were pressed, and sintered at $1100\~1600^{\circ}C$ for 20 hours. The optimal synthetic conditions at various compositions were differed from 1300 to $1600^{\circ}C$ Even in the optimal temperatures, pyrochlore or fluorite coexisted with minor amount of perovskite, $CeO_2\;or\;Ce_{0.75}Zr_{0.25}O_2$. It was confirmed that pyrochlore and fluorite structures were stable at $x\leq0.6\;and\;x\geq1.0$, respectively. Especially, the compositions of pyrochlore or fluorite showed non-stoichiometric compositions in that contents of Ca and Ti were more deficient and those of Zr and Ce were more excess than batch compositions with the increase of x value. These characteristics stemmed from the behavior of elements occupied at eight- and six-coordinated site, and then caused the coexistence of perovskite, $CeO_2\;or\;Ce_{0.75}Zr_{0.25}O_2$ along with pyrochlore or fluorite.

• Korean Journal of Food Science and Technology
• /
• v.22 no.4
• /
• pp.439-444
• /
• 1990

Fourteen varieties of soybeans grown in Korea were investigated for their chemical composition, yields and organoleptic properties of soybean curd. The soybean curd was prepared by soaking, grinding and heating of soybeans followed by filtration, coagulation with $CaSO_4$ and pressing. The proximate analysis showed that soybean curd had the moisture content of $75.0{\sim}82.0%\;and\;48.6{\sim}56.1%\;protein,\;14.8{\sim}40.4%\;lipids\;and\;6.4{\sim}26.8%$ carbohydrate by dry weight basis. The yield of volume total solids and protein from 100g of soybeans were $182.2{\sim}227.5cm^3,\;42.65{\sim}55.60%\;and\; 57.90{\sim}76.50%$, respectively. Among the 14 varieties, the highest volume yield was obtained from Suwon-141 which has the highest contents of moisture, carbohydrate and the lowest in lipids of soybean curd. The curd prepared with Baegun and Jangyeob contained relatively low values in moisture, protein and carbohydrate and yielded the lowest in volume yield. Therefor moisture, protein and carbohydrate contents in soybean curd affected greatly on volume yield. The organoleptic properties of odor and taste couldn't find any significant relationship with chemical composition of soybean curd eventhough there were some difference in their intensities among varieties.

• Korean Journal of Food Science and Technology
• /
• v.9 no.4
• /
• pp.245-250
• /
• 1977

Experiment were conducted to find out the effective drying method of citrus peel produced in Korea by varying the temperature of hot air, surface area of peels, peels from several citrus varieties and physicochemical treatment of the peel. 1. About $3{\sim}6\;days$ were required to reduce the moisture level of the peel from 70%(wet basis) to 20% at room temperature without forced convection. 2. Drying was speeded up until the temperature of hot air reached $60^{\circ}C$. Beyond that no significant increase in drying rate was observed. About 50 minutes were needed to reduce the moisture level (dry basis) to below 10% at $60^{\circ}C$ by forced convection 3. When the peel surface area was increased twice by cutting the peel into 256 fractions, the overall drying time (the time required to reduce the moisture level to 10%, dry basis) was shortened to 15 minutes from 50 mintes of the original peel. 4. No significant difference in drying rate was observed among the peels from several citrus varieties except Shaddock jabon and Citrus ponki tanaka, which dried more slowly than others. 5. Treatment of $Ca(OH)_2$ and the pressing of the peel before drying were effective in drying only when the initial moisture content was substantially higher.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.11 no.2
• /
• pp.86-91
• /
• 2008

Ships operating in littoral sea are likely to be subjected to accidental load such as stranding. Once she has damage on the hull structure, her ultimate strength will be reduced. This paper is to investigate the effect of the stranding damage on ultimate strength of ship structure by using a series of collapse tests. For the experiment, 720 mm $\times$720 mm in section and 900mm in length of five box-girder models with stiffeners were pre- pared. Of the five, one has no damage and faur have an diamond shaped damage which represents the shape of rock section in seabed. The damage size is different between models. Among the damaged models, the damages of 3 of them were made by cutting the plate and one by pressing to represent stranding damage. Experiments were carried out under pure bending load and the applied load and displacements were recorded. The ultimate strength is reduced as the damage size increases, as expected. The largest damaged model has the damage size of 30% of breadth and its ultimate strength is reduced by 21% than that of no damaged one. The pressed one has lower ultimate strength than cut one. This might be due to the fact that the plate around the pressed damage area effect negatively on the ultimate strength.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.306-309
• /
• 2005

One of the most critical issues in sol id oxide fuel cell (SOFC)running on hydrocarbon fuels is the risk of carbon formation from the fuel gas. The simple method to reduce the risk of carbon formation from the reactions is to add steam to the fuel stream, leading to the carbon gasification react ion. However, the addition of steam to fuel is not appropriate for the auxiliary power unit (APU) and potable power generation (PPG) systems due to an increase of complexity and bulkiness. In this regard, many researchers have focused on so-called 'direct methane' operation of SOFC, which works with dry methane without coking. However, coking can be suppressed only by the operation with a high current density, which may be a drawback especially for the APU and PPG systems. The single chamber fuel cell (SC-SOFC) is a novel simplification of the conventional SOFC into which a premixed fuel/air mixture is introduced. It relies on the selectivity of the anode and cathode catalysts to generate a chemical potential gradient across the cell. Moreover it allows compact and seal-free stack design. In this study, we fabricated honeycomb type mixed-gas fuel cell (MGFC) which has advantages of stacking to the axial direction and increasing volume power density. Honeycomb-structured SOFC with four channels was prepared by dry pressing method. Two alternative channels were coated with electrolyte and cathode slurry in order to make cathodic reaction sites. We will discuss that the anode supported honeycomb type cell running on mixed gas condition.