• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 C
• /
• pp.1216-1219
• /
• 1994

A reflection type SEED from LP-MOCVD grown InGaAs/GaAs ESQW structures, with 5% In fraction, has been fabricated and its basic characteristics were investigated. Its intrinsic region consists of 50 pairs of alternating $100{\AA}$ $In_{0.05}Ga_{0.95}As$ barrier and $100{\AA}$ GaAs layers. And a multilayer reflector stack of $Al_{0.12}Ga_{0.88}As(641{\AA})-/AlAs(774{\AA})$ was vertically integrated below the p-i-n structures. The device processing includes the mesa etching, insulator deposition, indium metallization, and thermal alloy for Ohmic contact. Photocurrent spectrum measurement showed the exciton absorption peak at 905nm and availability as a optical switching device. This device showed a contrast ratio of 2:1 by the reflectance spectrum measurement.

• 한국정보과학회 언어공학연구회:학술대회논문집(한글 및 한국어 정보처리)
• /
• 한국정보과학회언어공학연구회 2011년도 제23회 한글 및 한국어 정보처리 학술대회
• /
• pp.133-135
• /
• 2011

본 논문은 다중 도메인 대화 시스템에서 사용자의 발화에 가장 적합한 도메인을 결정하는 방법에 관하여 논한다. 다중 도메인 대화 시스템 구축 시, 도메인의 확장성 재고 및 각 도메인 별 특성의 효과적인 적용을 위해, 각 도메인 별 단일 도메인 대화 전문가를 구축하고, 다수의 도메인 대화 전문가들을 통합함으로써, 다양한 도메인을 처리할 수 있는 대화 시스템을 구축할 수 있다. 이 때, 자연스러운 대화 처리를 위해서 주어진 사용자의 발화에 가장 적합한 도메인을 결정하는 기술이 필요하다. 본 논문에서는 사용자 발화의 의도 분석 결과 및 이전 사용자 발화 도메인 정보를 이용하는 구축된 분류 모델에 기반한 도메인 결정 방법을 제안하고, 실험 결과를 통해 제안된 방법의 효과를 검증한다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2103-2105
• /
• 2005

Metal film type of resistor have been tested to invest maximum usable power at the pulsed high voltage and pulsed high current. Experiments were carried out using capacitor charging power supply and dump switch. Pulsed amplitude were varied from 1kV to 25kV. The peak current reached was 1kA. Datasheet are given for the limited pulsed power and energy for metal film type of resistor in nanosecond and microsecond time range. The experimental investigation of the threshold loading of the resistor in the high current and voltage pulsed mode has shown that the process of destruction of resistor has specific features for each mode. The mechanisms of failure and destruction of resistors under action of high-voltage and high-current pulses are discussed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.1519-1521
• /
• 2004

포항풍력에너지연구소와 (주)보국전기는 에너지 관리공단의 지원으로 2002년부터 직접구동형 풍력 터빈 KBP-750D에 사용될 발전기를 개발해 오고 있다. KBP-750D에 사용되는 발전기는 증속을 위한 gearbox를 사용하지 않는 직접 구동형 이라는 것과, 영구자석을 사용하여 여자하는 형식이라는 것이다. 이런 특징은 풍력발전에서 요구하는 주요 요구조건인 고효율, 고신뢰성을 만족시키기 위해서 매우 중요하다. 개발된 발전기는 25 rpm 정격에서 800 kW의 정격을 가지도록 설계되었다. 공극 직경은 3,320 mm 이며, stator의 길이는 705 mm, 4.5 mm의 공극, 84극을 가지고 있으며, 전체중량은 약 20 ton이다. 이 보고에서는 이 발전기의 물리설계 공학설계 등에 관해서 논의한다.

• 반도체디스플레이기술학회지
• /
• 제17권3호
• /
• pp.36-40
• /
• 2018

We have developed a nonlithographic patterning technique using polystyrene nanoparticles to form nanonet channel structures which is promising for high-performance TFT applications. Nanoparticles assisted patterning (NAP) is a technique to form uniform nano-patterns by applying lift-off and dry etch process. Oxygen plasma treatment was used to control the diameters of nanonet hole size to realize a branch width down to 100 nm. NAP technology can be very promising to fabricate nanonet structure with advantages of lower manufacturing cost and large-area patterning capability.

• Journal of Electrochemical Science and Technology
• /
• 제13권4호
• /
• pp.417-423
• /
• 2022

With the emerging importance of catalysts for water electrolysis, developing efficient and inexpensive electrocatalysts for water electrolysis plays a vital role in renewable hydrogen energy technology. In this study, a 1nm thickness of TiC-supported Ru catalyst for hydrogen evolution reaction (HER) has been successfully fabricated using an electron (E)-beam evaporator and thermal decomposition of gaseous CH₄ in a furnace. The prepared Ru/TiC catalyst exhibited an outstanding performance for alkaline hydrogen evolution reaction with an overpotential of 55 mV at 10 mA cm^-2. Furthermore, we demonstrated that the outstanding HER performance of Ru/TiC was attributed to the high surface area of the support and the metal-support interaction.

• Nuclear Engineering and Technology
• /
• 제55권5호
• /
• pp.1604-1615
• /
• 2023

In an open-pool type research reactor with a downward forced flow in the core, pipes can be under sub-atmospheric pressure because of the large pressure drop at the reactor core in the atmospheric pool. Sub-atmospheric pressure can result in air inflow into the pipe from the pressure difference between the atmosphere and the inside of the pipe, which in a postulated pipe break scenario can lead to the breakdown of the cooling pump. In this study, a plant-scale experiment was conducted to study air inflow in large piping systems by considering the actual operational conditions of an advanced research reactor. The air inflow rate was measured, and the entrained air was visualized to investigate the behavior of air inflow and flow regime depending on the pipe break size. In addition, the developed drift-flux model for a large vertical pipe with a diameter of 600 mm was compared with other correlations. The flow regime transition in a large vertical pipe under downward flow was also studied using the newly developed drift-flux model. Consequently, the characteristics of two-phase flow in a large vertical pipe were found to differ from those in small vertical pipes where liquid recirculation was not dominant.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 The Korea-Japan Plastics Processing Joint Seminar
• /
• pp.7-13
• /
• 2003

Microlens arrays were fabricated using a novel fabrication technology based on the exposure of a PMMA (Polymethylmethacrylate) sheet to deep X-rays and subsequent thermal treatment. X-ray irradiation causes the decrease of molecular weight of PMMA, which in turn decreases the glass transition temperature and consequently causes a net volume increase during the thermal cycle resulting in a swollen microlens. A new physical modeling and analyses for micro lens formation were presented according to experimental procedure. A simple analysis based on the new model is found to be capable of predicting the shapes of micro lens which depend on the thermal treatment. For the replication of micro lens arrays having various diameters with different foci on the same surface, the hot embossing and the microinjection molding processes has been successfully utilized with a mold insert that is fabricated by Ni-electroplating based on a PMMA microstructure of micro lenses. Fabricated microlenses showed good surface roughness with the order of 1nm.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1658_1659
• /
• 2009

PLS(Pohang Light Source) will begin the PLS-II project that has been funded by the KOREA Government in order to further upgrade the PLS which has operated since 1992. The control system of the PLS-II has distributed control architecture, with two layers of hierarchy; operator interface computer (OIC) layer and machine interface computer (MIC) layer. The OIC layer is based on SUN workstation with UNIX. A number of PC-based consoles allow to remotely operating the machine from the control room. PC-based consoles use the Linux or Windows operation system. Similar consoles in the experimental hall are used to control experiments. The MIC layer is directly interfaced to individual machine devices for low-level data acquisition and control. MIC layer is based on VMEbus standard with vxWorks real-time operating system. Executable application software modules are downloaded from host computers at the system start-up time. The MIC's and host computers are linked through Ethernet network. It should enable the use of hardware and software already developed for specific light source requirements. The core of the EPICS (Experimental Physics and Industrial Control System)[1] has been chosen as the basis for the control system software.

• 한국분말재료학회지
• /
• 제20권5호
• /
• pp.350-354
• /
• 2013

In this study, porous titanium samples were manufactured by space holder methods using two kinds of urea and sodium chloride space holders. Three-dimensional pore structures were obtained by a computed-tomography (CT) technique and utilized for finite element analysis in order to investigate the mechanical properties. The CT-based finite element analyses were in better agreement with the experimental results than unit cell model-based analyses. Both the experimental and CT-based results showed the same tendency that the elastic modulus decreased with increasing the porosities. The total porosity of the bulk body plays a key role in determining the elastic modulus of porous materials.