• 한국지구물리탐사학회:학술대회논문집
• /
• 2011.10a
• /
• pp.143-144
• /
• 2011

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1893-1896
• /
• 2005

Cutting force and face roughness have the largest influence on precision of a structure or processing efficiency in cutting processing. Thus cutting force model and face roughness model are necessary for this interpretation. In this paper, tool path model and face roughness model which consider the blade number of a tool and a revolution speed of tool and workpiece in the worm processing using side milling cutter are presented. This model was used to forcast the cusp. Experimental results show that the predicted cusp coincides with experimental one.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1933-1936
• /
• 2005

The isometric area of the anterior cruciate ligament was calculated during knee flexion-extension. Flexion-extension motion data of the joint were obtained using Fastrak and a three-dimensional motion measurement system. A total of five subjects were seated on a flat table and the tibia sensor position was measured with the femur fixed on the table. A three-dimensional knee model was constructed using a graphic tool to simulate the knee motion. Twenty seven positions of the tibia region and forty two positions of the femur region were selected and the distances between the determined tibial and femoral points were calculated. Highly isometric areas were found and displayed as three dimensional aspects.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.372-373
• /
• 2006

Chemical kinetics affects Cu CMP results (removal rate, Non uniformity etc.) Because Cu is removed by chemical action. Key factors in chemical kinetics are process temperature and concentration of slurry components. In this study, Hydrogen peroxide and citric acid were selected as a oxidant and a complexing agent and Slurry were made by mixing this components. In order to study effects of Chemical Kinetics, X-ray photoelectron spectroscopy (XPS) were performed on Cu sample after etching test as concentration of citric acid and slurry temperature. Finally Cu CMP was performed as same conditions.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.570-573
• /
• 2001

Safety is very important to operate nuclear power plant. To have the safety, nuclear power plant should be run without trouble. This paper presents the application of a failure diagnosis approach based on discrete event system theory to the Main Feedwater System for Safe Integral Reactor.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.594-597
• /
• 2001

As many industrial systems become more complex, they become extremely difficult to diagnose the cause of failures. The subject of this paper is ECCS(Emergency Core Cooling System) part of PWR(Pressurized Water Reactor). This paper presents modeling and diagnoser construction of ECCS based on discrete event system theory. Also, this paper presents that the ECCS system is diagnosible in our approach.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.358-359
• /
• 2005

Chemical mechanical polishing(CMP) process depends on a variety of variables. Especially, surface roughness of pad plays a key role in material removal in CMP in terms of transportation ability of pores and real contact area. The surface roughness is deteriorated with polishing time by applied pressure and relative velocity. In this reason, diamond conditioner has been used to maintain the roughness on the pad. The authors try to investigate the correlation between pad roughness and frictional behavior by comparing ex-situ conditioning with in-situ conditioning.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.383-384
• /
• 2006

Ventilated disc was improved for reducing judder and heat. But the crack among vent holes occurs due to stress concentration. We investigate the stress distribution of vent holes. The vent holes with shape of a right angle, a chamfer and rounding was analyzed. The result of FEA was that rounded vent holes have a minimum stress. Also Maximum stress distributed within holes. Therefore We suggest that the rounded vent holes is good to reduce the crack.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.521-522
• /
• 2006

Occlusal loading is considered as the main factor of noncarious cervical lesions. The goal of this study is to identify stress distribution using three dimensional finite element analysis, when occlusal loading is applied on the cervical lesion of human tooth. A finite element model was constructed from micro-CT image and three kinds of static force(500 N) were assumed. In all cases stress concentrates on the same area in the cement-enamel junction. This finding is consistent with published experimental results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.491-492
• /
• 2006

In the microstereolithography which can make 3-D microstructures, curing depth is different according to exposure energy. Curing depth has to be controlled to fabricate complex 3-D microstructures with overhang shape. It becomes increases when the exposure energy increases. And photocurable resin is cured when the exposure energy is bigger than critical energy. So optimal exposure energy has to be found to fabricate overhang structures without being gel. To make thinner layer, UV absorber is used and exposure pattern is changed. In this paper, we find curing characteristics according to exposure energy, and fabricate microstructures with overhang shape.