• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.7
• /
• pp.1-7
• /
• 2015

In this paper, we demonstrated a polarimetric fiber pressure sensor using a polarization-diversity-loop-based Sagnac interferometer(PDLSI) composed of polarization-maintaining fiber(PMF) and a fiber Bragg grating(FBG). In order to compare the pressure sensitivity for various kinds of PMF, three kinds of bow-tie PMF were employed as sensor heads. The maximum pressure sensitivity was measured as approximately -15.07nm/MPa, and an R2 value to represent sensor linearity was measured as ~0.992 at the sensor system using corresponding PMF over a pressure range of 0-0.3MPa. An FBG was utilized and located adjacent to the PMF segment for compensating temperature-induced errors in the measurement of pressure. The pressure sensitivity of the proposed sensor was improved by approximately four times compared with the previously reported pressure sensor based on polarization-maintaining photonic crystal fiber.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.5
• /
• pp.145-150
• /
• 2007

Optical communication according to request of technology of communications and optical fiber to be full filed faster communication and pass over transmission capacity limit per unit area, per unit hour appeared, and this optical fiber acts the biggest role to influence performance of optical communication network. Optical fiber(PMF Polarization Maintaining Fiber) is used, and is used by electric field measurement, self-discipline measurement, sensor(Sensor) Department by high definition measure such as thermometry and storehouse component that use because make broad sense status and polarized light information in passageway and union with storehouse integrated circuit etc. that use broad sense interference developing could transmit in state that keep transmitting broad sense plane of polarization is polarized light existence. Also, research is developed by optical fiber for Coherent communication recently.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.12
• /
• pp.33-37
• /
• 2010

In this paper, we have demonstrated absolute wavelength tuning in an optical fiber comb filter based on a polarization-diversity loop configuration by controlling the current injected into enameled wires wound on polarization-maintaining fibers (PMF's), that is, adjusting Joule heat generated from enameled wires. The proposed fiber comb filter consists of a polarization beam splitter, a half-wave plate, a quarter-wave plate, and PMF's. And we observed wavelength change of spectral dips in transmission spectra of the fabricated filter by varying an input current applied to enameled wires. The absolute wavelength of the filter could be controlled in proportional to the square of the input current with good linearity, and the rate of the wavelength shift with respect to the input current was measured as 36.79[nm/$A^2$].

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.02a
• /
• pp.186-187
• /
• 2001

광섬유 브래그 격자를 이용한 고정밀도 센서 시스템은 불균형(unbalanced) 마하 젠더 간섭계를 이용한 interrogation 기법을 많이 사용하고 있다. 그러나 간섭성을 이용한 interrogation 기법은 작은 온도 변화, 진동과 같은 외부 환경 변화에 매우 민감하다 이 논문은 불균형 마하 젠더 간섭계 대신 편광 유지 광섬유 (polarization maintaining fiber , PMF) 루프 미러(loop mirror)를 이용한 interrogation 시스템을 구현하였다. (중략)

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1265-1266
• /
• 2015

본 논문에서는 PMF와 FBG로 구성된 PDL 기반 사냑 간섭계를 이용하여 편광 간섭형 광섬유 압력 센서를 구현하였다. 여러 종류의 PMF들에서 압력 민감도를 비교하기 위해, 서로 다른 세 종류의 보우-타이형 PMF를 센서부로 사용하였다. 구현된 광섬유 압력 센서를 이용하여 0~0.3 MPa의 범위에서 압력 측정을 수행하였으며, 최대 압력 민감도는 근사적으로 -15.07 nm/MPa로 측정되었고, 센서의 선형성을 나타내는 $R^2$값은 ~0.992로 측정되었다. 제안된 센서는 FBG를 이용하여 외부 온도 변화의 보상이 가능하면서도, 이전의 편광유지 광자결정 광섬유 기반 압력 센서에 비해 압력 민감도를 4배까지 증가시킬 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.73-76
• /
• 1997

A low loss x-cut LiNbO$_3$ optical waveguide was fabricated by Ti in-diffusion and the guided-mode properties and total insertion loss of pigtailing with polarization maintaining fiber(PMF) were investigated and measured at optical wavelength 15507. For formaing the waveguide, the parameters of diffusion Ti thickness, waveguide line-width, length, diffusion temperature, time and atmosphere were set 1400$\AA$, 8${\mu}{\textrm}{m}$, 3.3cm, 105$0^{\circ}C$, 8 hours and wet bubbled oxygen, respectively. and then After the polishing and pigtailing, it showed that total insertion loss was -4.1dB for TM mode, -5.5dB for TE mode, and mode size, that is, horizontal/vertical sizes were 13.87/18${\mu}{\textrm}{m}$ for TM mode, 9.61${\mu}{\textrm}{m}$/6.5${\mu}{\textrm}{m}$ for TE mode.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.7
• /
• pp.557-564
• /
• 1998

A low loss x-cut $LiNbO_3$optical waveguide was fabricated by Yi in-diffusion, and the properties of guided-mode and the total insertion loss of the pigtailed waveguide with polarization maintaining fiber(PMF) were measured at optical wavelength 1550nm. for forming the waveguides, the parameters of diffusion, Ti thickness, waveguide line-width, length, diffusion temperature, time and atmosphere were set $1400{\AA}$, $8{\mu}m$, 3.3cm, $1050^{\circ}C$, 8 hours and wet bubbled oxygen, respectively. And then after the polishing and piatailing, it showed that the total insertion loss was -4.1dB for TM mode, -5.5dB for TE mode, and mode size, that is, the horizontal/ vertical size were $13.8{\mu}m/18{\mu}m$ for TM mode, $9.6{\mu}m/6.5{\mu}m$ for TE mode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.425-427
• /
• 1997

Ti:LiNbO$_3$optical waveguides were fabricated as a function of Ti thickness and pigtailed with polarization maintaining fiber(PMF). The near field patterns and total insertion loss of these sample was showed and measured for optical wavelength 1550nm. The fiber-to-waveguide coupling loss was described also .

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.101-104
• /
• 1998

We report some methods for measuring a LiNbO$_3$ optical phase modulator bandwidth. Since Mach-Zehnder waveguide type, one of methods for modulation bandwidth measurement, is comparatively simple and useful, it was adapted in this work. In order to confirm this method, the waveguide of single and Mach-Zehnder type were fabricated on the same wafer. The Mach-Zehnder interferometric waveguide and the single channel waveguide were used for the measurement of the phase modulator's driving voltage and bandwidth for device fabrications, respectively. Ti-860$\AA$ in-diffusion was achieved in a wet-bubbling oxygen environment at 105$0^{\circ}C$/8hours. LINbO$_3$ internal chips were pigtailed to PMF(polarization maintaining fiber)/SMF(single mode fiber) using an epoxy curing technique. Examined were optical properties such as an insertion loss, propagation loss and mode size, and the loss mechanism of optical coupling between an optical fiber and a waveguide was considered.