• Journal of Power Electronics
• /
• v.15 no.1
• /
• pp.131-145
• /
• 2015

The voltage-source inverters (VSI) supplying a motor drive are prone to open transistor faults. To address this issue in fault-tolerant drives applicable to electric vehicles, a new open transistor fault diagnosis (FD) method is presented in this paper. According to the proposed method, in order to define the FD index, the phase angle of the converter output current is estimated by a simple trigonometric function. The proposed FD method is adaptable, simple, capable of detecting multiple open switch faults and robust to load operational variations. Keeping the FD in mind as a mandatory part of the fault tolerant control algorithm, the FD block is applied to a five-phase converter supplying a multiphase fault-tolerant PM motor drive with non-sinusoidal unbalanced current waveforms. To investigate the performance of the FD technique, the fault-tolerant sliding mode control (SMC) of a five-phase brushless direct current (BLDC) motor is developed in this paper with the embedded FD block. Once the theory is explained, experimental waveforms are obtained from a five-phase BLDC motor to show the effectiveness of the proposed FD method. The FD algorithm is implemented on a field programmable gate array (FPGA).

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.6
• /
• pp.536-543
• /
• 2004

Slotless Permanent Magnet Brushless DC Motor(PM BLDC) with the characteristics of high speed and power density has been more widely used In Industrial and factory machine. Generally, PM BLDC meter is necessary that the three Hall-lCs evenly be distributed around the stator circumference in case of the 3 phase motor. The Hall-ICs are set up in PM BLDC Motor to detect the main flux from the rotor. therefore the output signal from Hall-ICs is used to drive a power transistor to control the stator winding current. However, instead of using three Hall-ICs, if it used only one Hall-IC, we can estimate information of the others phase in sequence through a rotor This paper identified the characteristics and performance by using one Hall-IC with the 3-phase, 2-pole, 6-slot PM BLDC motor.

• Journal of Magnetics
• /
• v.20 no.1
• /
• pp.91-96
• /
• 2015

As many researchers are relentlessly trying to improve the power generation schemes from the power grid, to meet the constantly increasing electricity demand. In this paper, the results of a finite element analysis are carried out to study on a design optimization of an asymmetric air-gap structure in 3-phase Permanent Magnet Brushless DC Motors. To achieve a high efficiency for a 3-phase PM BLDC motor, the asymmetric air-gap structure is proposed considering the rotation direction of a motor. Generally, a single-phase BLDC motor is applied asymmetric air-gap structure for starting. This is because the asymmetric air-gap structure causes reluctance variation so the motor can utilize reluctance torque toward a rotation direction. In this paper, the asymmetric air-gap is applied to 3-phase BLDC SPM motor so it utilizes reluctance torque with alignment torque. A proposed model is designed by 2-D FE analysis and the results are verified by experimental test.

• International Journal of Precision Engineering and Manufacturing
• /
• v.3 no.3
• /
• pp.62-68
• /
• 2002

To satisfy the requirement of the one axis linear positioning system, which is following control of the desired trajectory without following error and is the high positioning accuracy, feed-forward loop having cogging force model is proposed. In the one axis linear positioning system with linear PM motor, cogging force acting as disturbance is modeled analytically. Analytic model of cogging force is verified by result measured from positioning system constructed with linear PM motor. Measured result is very similar with proposed analytic model. Cogging force model is used as feet forward loop in control scheme of linear positioning system. Cogging force feed-forward'loop is obtained from analytic model of cogging farce. Trajectory following error is reduced from 300nm to 100nm by applying the proposed cogging farce feed-forward loop. By using analytic model of cogging force, the control scheme is simplified. Also this analytic model is applicable to calculation of characteristic value of positioning system in design process.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.4
• /
• pp.56-64
• /
• 2006

Generally, Permanent Magnet Brushless DC Motor(PM BLDC) is necessary the Hall-IC to detect the rotor position. But it will take place the operation standstill of motor or error of rotor position detection according to the circumference temperature, humidity, or limited surroundings. This paper propose the algorithm of rotor position detection only using one or two Hall-IC. Therefore we can estimate information of the others phase in sequence through a rotor instead of using three Hall-IC at 3 phase motor. This paper identify the same characteristics, performance and function of protection circuit by the proposed algorithm with the 3 phase PM BLDC motor in comparison with general method.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.25-27
• /
• 2007

Brushless DC Motor (BLDCM) is DC motor and Interior PM Synchronous Motor (IPMSM) is AC motor. Besides their way of control is different. But it is similar that both motors rotate synchronous velocity and use the permanent magnet. So, it is an objective to grasp a tendency of motor design and efficiency of motor through a characteristic comparison of BLDCM and IPMSM with the same power, rotation velocity, torque and input voltage.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.7
• /
• pp.346-352
• /
• 2006

In Brushless DC Motor, there are Permanent Magnets (PMs) with driving circuit and sensor for detecting to rotor position and rotation speed. In the case of using hall IC sensor which response to magnetic flux, that is required to additional sensor magnet for rotor position detecting. Most of BLDC motor, However, take asymmetrical overhang of PM in rotor instead of additional sensor magnet for operating of hall IC sensor. The asymmetrical overhang of PM occur rotor thrust to z-axis direction that is lead to not only damage of bearing but also intensive noise and vibration. Therefore, the analysis of magnet overhang effect in the side of vibration and drive to hall If sensor is required to precise. In this paper, 2-D Finite Element Method is used to solve precise field computation and thrust of z-axis direction considering asymmetrical magnet overhang. And also the z-axis thrust from the analysis result is compared to experimental result. In conclusion, the purpose of this paper minimize to noise and vibration of BLDC Motor as analyzes to asymmetrical magnet overhang effect.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.50 no.3
• /
• pp.117-124
• /
• 2001

The aim of this paper is to develop a controller of multi-phase bipolar brushless DC (MPB BLDC) motors for an electric bicycle. A MPB BLDC motor has a Permanent magnet rotor in which the magnetic arrangement is radial to the shaft and integral to the rotor laminations. This technique concentrates flux, giving a higher flux density than a surface-mounted PM motor and increases reluctance torque. The stator of MPB BLBC motor has parallel winding, allowing multi-phase separate independent controllability. It gets much more high power than wye-connection at same low voltage. The conventional techniques of exited with modulation(EWM), bidirection control, and partial square wale control are Proposed with one H-bridge and two photo sensors per phase. The Proposed controller is satisfied for the limited speed control and designed for system stability Experimental results show the performance of the proposed controller of MPB BLDC motors for an electric bicycle.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.1
• /
• pp.57-65
• /
• 2007

Along with the development of power electronics and magnetic materials, permanent magnet (PM) brushless direct current (BLDC) motors are now widely used in many fields of modern industry BLDC motors have many advantages such as high efficiency, large peak torque, easy control of speed, and reliable working characteristics. However, Compared with the other electric motors without a PM, BLDC motors with a PM have inherent cogging torque. It is often a principle source of vibration, noise and difficulty of control in BLDC motors. Cogging torque which is produced by the interaction of the rotor magnetic flux and angular variation in the stator magnetic reluctance can be reduced by sinusoidal air-gap flux density waveform due to reduction of variation of magnetic reluctance. Therefore, this paper will present a design method of magnetizing system for reduction of cogging torque and low manufacturing cost of BLDC motor with isotropic bonded neodynium-iron-boron (Nd-Fe-B) magnets in ring type by sinusoidal air-gap flux density distribution. An analytical technique of magnetization makes use of two-dimensional finite element method (2-D FEM) and Preisach model that expresses the hysteresis phenomenon of magnetic materials in order for accurate calculation. In addition, For optimum design of magnetizing fixture, Factorial design which is one of the design of experiments (DOE) is used.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.3 s.22
• /
• pp.18-23
• /
• 2005

Ships have been propelled and maneuvered by electrical drives since trle late seventies. Recently, rare earth PMs allow the design of brushless motors with very high efficiency over a wide speed range. This is the most important factor in ship propulsion technology. Several types PM motors have been developing for ship propulsion system. However these have disadvantage such as cogging torque. It causes an undesired effect that contributes to output ripple, vibration, and noise of machine. Therefore several techniques may be adopted in designing PM motor in order to reduce the cogging torque. This paper describes cogging torque receding methods such as adjusting arigap length, magnet arc, and magnet thickness. That are analysed by using the finite element method(FEM) and the maxwell stress tensor method.