• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.533-534
• /
• 2007

This paper investigates impulsive noise from a pole transformer in low voltage distribution system for power line communication. EMI noise from the pole transformer is indicated from the experiment. The noise has certain characteristics because it is caused by partial discharge. The noise level is above -35dBm without a filter. Therefore, the filter which is made of ferrite is used in order to eliminate the noise. the noise filters should be applied to both the phase line and the neutral line. Otherwise, It is likely to have little overall impact on elimination of noises. the performance of filter is verified with various experiments. In conclusion, the equivalent circuit of power line communication including noise source is described as a lumped circuit.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.313-315
• /
• 2004

최근의 전력선통신(PLC: Power Line Communication)은 협대역인 450KHz에서 광대역인 30MHz로 확대되어 고속의 데이터 전송이 가능하게 되었다[1]. 본 논문에서는 광대역 채널특성과 더불어 고속의 데이터 전송까지 가능하도록 하기 위해 새로운M-ary SS(spread spectrum) 기반의 고속 전력선통신시스템을 제시하고 임펄스잡음과 같은 전력선 채널환경 하에서의 BER(Bite Error Rate)특성에 대한 모의실험을 거쳐서 제안 방식의 유용성을 확인하였다

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.327-329
• /
• 2004

전력선통신(PLC : Power Line Communication)은 실제 네트워크를 작성할 수 있는 이점은 있지만 이로 인해서 말단의 망 구성이 복잡해지고 여러 부하 장치들의 사용과 운용이 시간과 공간에 따라 전송 특성이 수시로 가변 하는 특성을 가지게 된다. 이러한 특성은 통신시스템 성능상의 다중 경로페이딩의 지연과 성분을 가지게 되므로, 열악한 통신 채널 환경 띤 다중 사용자 간섭에 의한 원인이 된다. 본 논문에서는 이런 원인을 극복하기 위한 한 가지방편으로서, 저간섭 전력선 통신에 적용 가능한 이진 ZCD 확산 코드를 제시하고, 상관 특성을 도출해 봄으로서, 그 유효성을 확인한다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.05a
• /
• pp.921-922
• /
• 2014

에너지 절약과 에너지 재생산 측면에 있어서 일상생활에서 낭비되고 있는 에너지를 다시 회수하여 재사용 할 수 있는 시스템은 경제적인 측면에서 그 가치가 높다고 할 수 있다. 이러한 관점에서 일반 주유소나 도장시설 등과 같은 환경에서 무심히 대기로 배출되는 휘발성 유증기를 포집하여 다시 에너지로 재사용하게 되면 경제적인 효과가 높다고 할 수 있다. 본 논문은 기존의 PLC 기반으로 동작하고 있는 휘발성유기화합물에 대한 액화장치(Liquefaction equipment)를 정보통신기술(Information & Communication Technology)을 접목시켜 액화장치를 효율적으로 관리하고, 내부 액화온도를 적절하게 제어하여 액화기의 효율을 향상시키고자 한다. 또한 액화기의 운전상태에 대한 정보를 ZigBee 기반의 무선 통신기술을 도입하여 원격지 관리서버로 액화기 상태정보를 전송하여 액화기에 대한 합리적인 운전 스케쥴 관리와 에너지 생산성을 높이고자 하며, 스마트기기로 모니터링 할 수 있도록 액화장치의 정보를 제공하고자 한다.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1022-1027
• /
• 2003

The Motion controllers provide the sophisticated performance and enhanced capabilities we can see in the movements of robotic systems. Several types of motion controllers are available, some based on the kind of overall control system in use. PLC (Programmable Logic Controller)-based motion controllers still predominate. The many peoples use MCU (Micro Controller Unit)-based board level motion controllers and will continue to in the near-term future. These motion controllers control a variety motor system like robotic systems. Generally, They consist of large and complex circuits. PLC-based motion controller consists of high performance PLC, development tool, and application specific software. It can be cause to generate several problems that are large size and space, much cabling, and additional high coasts. MCU-based motion controller consists of memories like ROM and RAM, I/O interface ports, and decoder in order to operate MCU. Additionally, it needs DPRAM to communicate with host PC, counter to get position information of motor by using encoder signal, additional circuits to control servo, and application specific software to generate a various velocity profiles. It can be causes to generate several problems that are overall system complexity, large size and space, much cabling, large power consumption and additional high costs. Also, it needs much times to calculate velocity profile because of generating by software method and don't generate various velocity profiles like arbitrary velocity profile. Therefore, It is hard to generate expected various velocity profiles. And further, to embed real-time OS (Operating System) is considered for more reliable motion control. In this paper, the structure of chip-based precision motion controller is proposed to solve above-mentioned problems of control systems. This proposed motion controller is designed with a FPGA (Field Programmable Gate Arrays) by using the VHDL (Very high speed integrated circuit Hardware Description Language) and Handel-C that is program language for deign hardware. This motion controller consists of Velocity Profile Generator (VPG) part to generate expected various velocity profiles, PCI Interface part to communicate with host PC, Feedback Counter part to get position information by using encoder signal, Clock Generator to generate expected various clock signal, Controller part to control position of motor with generated velocity profile and position information, and Data Converter part to convert and transmit compatible data to D/A converter.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.11
• /
• pp.2043-2047
• /
• 2010

This study is to solve problems of depletion of RF bandwidth frequency, confusion possibility, security that current wireless communications system have and is to confirm possibility of applying next generation network. To solve problems of current wireless communications system, visible light communications system for power line communications using ATmega16 Microcontroller is was realized and receiver property was analyzed. PLC exclusive chip APLC-485MA, Microcontroller ATmega16, 5pi bulb type LED and high flux LED, visible light receiving sensor LLS08-A1 were used for transmitter and receiver. Performance was analyzed by designed program and an oscilloscope. It was showed average 20% improved receiver rate rather than bulb type LED in the case of high flux LED through voltage change rate on communication distance and LED type of distance between 10 to 50 cm. The blue LED showed the best performance among measured LED types with above 10% of voltage decreasing rate. But As it gradually becomes more distant, the precise date was difficult to obtain due to weak light. To overcome these sort of problems, specific values such as changing conditions and efficiency value relevant to light emitting parts and visible light receiving sensor should be calculated and continuous study and improvements should also be accomplished for the better communications condition.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.10a
• /
• pp.577-578
• /
• 2010

The current marine communication networks are usually composed of NMEA0183, NMEA2000, and MiTS protocols which are located on the physical layer based on RS-422, RS-485, CAN, and EtherNet. This paper proposes a new bridge based on the DC power line communication technique supported from the NMEA0183 to design inside marine systems.

• The Journal of the Korea Contents Association
• /
• v.8 no.6
• /
• pp.1-7
• /
• 2008

The paper is to solve the problem of existing sound system, which has difficulties of system organization and the increase of additional install cost and unfriendly interior. To solve the existing system, we drew the new sound system based on PLC and studied it. A transmitter and a receiver were designed using the PLC chip INT5500CS. Sound system was configured with a CD player that sound signals are sent from the transmitter and a speaker connected to the receiver. For analysis of characteristics of this system, a USBPre external sound card and Smaart Live 5 which is a PC-based sound measuring program were added. As a result of our experiment, the measured signal level is $2{\sim}3$[dB] lower than reference signal, latency is 16.69[ms] and the specific character of coherency is bad in high frequency band. Otherwise, this system transmits and receives signals over 90[%] in good condition as a result of measuring pink noise, frequency(1kHz), and phase, magnitude. In view of the result so far achieved, the system designed our team has excellent performance, it resolves defect of existing audio signal transmition system.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.3
• /
• pp.285-290
• /
• 2016

In rural area, our farmers confront decreasing benefits owing to imported crops and increased cost. Recently, the government encourage the 6th Industry that merges farming, rural resources, and information and communication technology. Therefor the government makes an investment in supplying 'smart greenhouse' in which a farmer monitor growing crops and environment information to control growing condition. The objective of this study is developing an Moving Monitor and Control System for crops in green House. This system includes a movable sensing unit, a controlling unit, and a server PC unit. The movable sensing unit contains high resolution IP camera, temperature and humidity sensor and WiFi repeater. It rolls on a rail hanging beneath the ceiling of a green house. The controlling unit contains embedded PC, PLC module, WiFi router, and BLDC motor to drive the movable sensing unit. And the server PC unit contains a integrated farm management software and home pages and databases in which the images of crops and environment informations. The movable sensing unit moves widely in a green house and gathers lots of information. The server saves these informations and provides them to customers with the direct commercing web page. This system will help farmers to control house environment and sales their crops in online market. Eventually It will be helpful for farmers to increase their benefits.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.1
• /
• pp.124-130
• /
• 2011

In this paper, we propose a method for the efficient power use in power outage. The cost is high and conversion into the other function is difficult since the terminal used in conventional home network system has a dedicated function. This method is based on home network system employed with photovoltaic system. Throughout the modularization of the terminal, the variable function and cost reduction can be achieved. Additionally the unit cost can be reduced by using the power line communication. The prototype of light-control terminal has been implemented. The experimental results with the terminal show the performance of light-control system and the possibility of the commercialization can be achieved.