• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.414-417
• /
• 2001

SRG (Switched Reluctance Generator) have many advantages such as high efficiency, low cost, high-speed capability and robustness compared with characteristics of other machines. However, the control methods that have been adopted for SRGs are complicated. This paper proposes a simple control method using PID controller that only controls turn-off angles while keeping turn-on angles of SRG constant. The linear characteristics between the generated current and the turn-off angle can be used to control the turn-off angle for load variations. Since the reference current for generation can be produced from an error between the reference and the real voltage, it can be controlled to keep the output voltage constant. The proposed control method enhances the robustness of this system and simplifies the hardware and software by using only the voltage and speed sensors. The proposed method is verified by experimental results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.319-324
• /
• 2001

This paper presents the motion control of a mobile robot with arc sensor for lattice type welding. Its dynamic equation and motion control method for welding speed and seam tracking are described. The motion control is realized in the view of keeping constant welding speed and precise target line even though the robot is driven along a straight line or corner. The mobile robot is modeled based on Lagrange equation under nonholonomic constraints and the model is represented in state space form. The motion control of the mobile robot is separated into three driving motions of straight locomotion, turning locomotion and torch slider controls. For the torch slider control, the proportional integral derivative (PID) control method is used. For the straight locomotion, a concept of decoupling method between input and output is adopted and for the turning locomotion, the turning speed is controlled according to the angular velocity value at each point of the comer with range of $90^{\circ}$ constrained to the welding speed. The experiment has been done to verify the effectiveness of the proposed controllers. These results are shown to fit well by the simulation results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 B
• /
• pp.985-987
• /
• 1999

In this Paper, speed controller design for disturbance system is explained robust control for disturbance. This paper usig CDM. It has highest sensitivity in plant variation and disturbance. After that computer simulation were executed to confirm ability of compared with PID controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.839-844
• /
• 1992

There are many specific requirements in the actuation, system for high speed underwater vehicle, such as size, weights, power etc.. In this paper, a high performance compact hydraulic actuation system to satisfy such requirements was designed. The controller of the system was designed using both the conventional PID and VSC which were known to have reliability, robustness respectively. The performance analysis was done for the designed actuation system through computer simulation.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2000년도 추계학술대회
• /
• pp.104-108
• /
• 2000

본 논문에서는 BLDC 모터에서 속도 센서를 사용하지 않고 홀센서의 출력만을 이용하여 속도 제어를 수행하였다. 모터는 100W급을 이용하였으며, 부하는 팬을 이용하였다. 속도 계측은 BLDC 모터에 불어 있는 3개의 홀센서 출력을 이용하였다. 홀센서 간에 간격이 불균일하므로 3개의 홀 센서를 구분하여 각각이 한 바퀴 회전하는데 까지의 시간을 측정하여 속도를 측정하였다. ARMAX 모델에 기초하여 전체 시스템의 파라미터를 구하였다. 구해진 파라미터에 PID 제어기를 구성하여 속도 제어를 수행하였다. 속도 제어 결과 0.1% 오차 미만으로 속도가 원활하게 유지되는 것을 확인하였다.

• Journal of Astronomy and Space Sciences
• /
• 제20권2호
• /
• pp.153-162
• /
• 2003

인공우주물체의 추적 및 관측을 위해 LX-200 12인치 망원경시스템을 도입하여 시스템의 구동부(모터, 모터드라이버, 모션컨트롤러)를 응답특성이 빠르고 능동제어가 가능한 것으로 개선하였다. 또한, PC를 이용하여 대상물의 실시간 궤적정보를 계산하여 모터 드라이버 내의 PID 제어기에 신호를 제공하였고, 명령신호 제어주기도 20ms까지 줄였다. 그 결과, 가대의 구동속도는 $18^{circ}/sec$로 향상되고 상용시스템보다 응답속도가 빠르며 대상물의 이미지 관측시 flipping 현상을 최소화하는 시스템을 개발하였다.

• 대한기계학회논문집A
• /
• 제28권8호
• /
• pp.1125-1134
• /
• 2004

This paper presents a mathematical model which is about the dynamics of not only a two wheel steering vehicle but a four wheel steering vehicle. A sliding mode ABS control strategy and PID rear wheel control logic are developed to improve the brake and cornering performances, and enhance the stability during emergency maneuvers. The performances of the controllers are evaluated under the various driving road conditions and driving situations. The numerical study shows that the proposed full car model is sufficient to accurately predict the vehicle response. The proposed ABS controller reduces the stopping distance and increases the vehicle stability. The results also prove that the ABS controller can be employed to a four wheel steering vehicle and improves its performance. The four wheel steering vehicle with PID rear wheel controller shows increase of stability when a vehicle speed is high and sharp cornering maneuver when a vehicle speed is low compared to that of a two wheel steer vehicle.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권5호
• /
• pp.525-536
• /
• 2017

Course keeping is hard to implement under the condition of the propeller stopping or reversing at slow speed for berthing due to the ship's dynamic motion becoming highly nonlinear. To solve this problem, a practical Maneuvering Modeling Group (MMG) ship mathematic model with propeller reversing transverse forces and low speed correction is first discussed to be applied for the right-handed single-screw ship. Secondly, a novel PID-based nonlinear feedback algorithm driven by bipolar sigmoid function is proposed. The PID parameters are determined by a closed-loop gain shaping algorithm directly, while the closed-loop gain shaping theory was employed for effects analysis of this algorithm. Finally, simulation experiments were carried out on an LPG ship. It is shown that the energy consumption and the smoothness performance of the nonlinear feedback control are reduced by 4.2% and 14.6% with satisfactory control effects; the proposed algorithm has the advantages of robustness, energy saving and safety in berthing practice.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.149-149
• /
• 2000

We experimented on AGV driving test with color CCD camera which is setup on it. This paper can be divided into two parts. One is image processing part to measure the condition of the guideline and AGV. The other is part that obtains the reference steering angle through using the image processing parts. First, 2 dimension image information derived from vision sensor is interpreted to the 3 dimension information by the angle and position of the CCD camera. Through these processes, AGV knows the driving conditions of AGV. After then using of those information, AGV calculates the reference steering angle changed by the speed of AGV. In the case of low speed, it focuses on the left/right error values of the guide line. As increasing of the speed of AGV, it focuses on the slop of guide line. Lastly, we are to model the above descriptions as the type of PID controller and regulate the coefficient value of it the speed of AGV.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권4호
• /
• pp.538-550
• /
• 1998

The variable frequency and variable voltage AC source made by a conventional inverter which is composed of power semi-conductors includes much noises in sine wave due to high frequency switching of DC source. In this paper the 3rd low pass LC filter for a variable speed 3 phase induction motor driven by a full bridge inverter is introduced to solve the EMI problem by serious noise current. The utility of a modified 3rd order Butterworth LC filter is confirmed through FFT analysis of sine waves and noiseless ACsource can be obtained by the proposed LC filter. The speed of a 3 phase induction motor driven by a full bridge inverter with a LC filter is satisfactorily controlled by a digital PID controller under the condition of stepwise load and setpoint changes.