• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.3
• /
• pp.232-238
• /
• 2015

A sensorless control algorithm of brushless DC (BLDC) motors with a model current based on 120 degree conduction mode is proposed in this paper. The rotor speed and position can be estimated using the current model of BLDC motor, which is a modified version of the conventional current model of permanent magnet synchronous motor. The rotor speed and position can be obtained using the difference of the actual current and the model current. The position error caused by the parameter errors of the model current is compensated using a PI controller and the feedback loop of the real current. The validity of the proposed sensorless control algorithm is verified through simulation.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.63 no.4
• /
• pp.219-225
• /
• 2014

The purpose of this paper is to control of the low-speed, high-precision PMSM 2-axes pitch/turning. In this paper, apply the PAM-PWM inverter for it. However, The PAM-PWM inverter, control algorithms and hardware is complex. But it is possible to improve the performance in the low-speed operation can reduce the effect of the PWM ripple and Dead Time of inverter by applying suitable DC-bus voltage control. The direct driver PMSM(Permanent Magnet Synchronous Motor) configured to vector control part, PAM control part and the other controller. The vector control part includes PI current, speed control, additional space vector modulation. PAM control part has to have PI voltage controller and P current controller for DC-bus voltage control. Besides, the motor position estimator, the speed estimator and the counter electromotive force and Dead Time Compensation are added. With this arrangement, PMSM was driven with a low pole pitch/turning by performing the current control to the current command or torque command is the paper. As a result, it was possible to minimize the disturbance component that appears in the drive in proportion to the DC voltage magnitude. The use of a hydraulic drive method for a two-axis bubble column is a typical tank. When using the PWM PAM inverter driver is in the turret can be driven by high-precision, low vibration, low noise compared to the hydraulic drive may contribute to the computerization of the turret.

• Proceedings of the KIEE Conference
• /
• 1999.07c
• /
• pp.1063-1066
• /
• 1999

This paper presents an extended integral control with the PID controller by introducing the delay and decaying factors. The convolution integral control scheme is developed by substituting proportional convolution integral controls for the proportional-integral control. So far, the integral part of the PI controller produces a signal that is proportional to the time integral of the input of the controller. The steady-state operation points are affected forever by the errors in the past due to the input signal containing the information of the errors in the past. These phenomina may cause some disturbances for other control purposes related to the given PI control. Introduction of forgetting factors of the error in the past can resolve the disturbance problems. Various forgetting factors are developed using the delay, the decaying factors, and the combination of the delay and the decaying factors. The proposed various extended integral control schemes can be applicable to corresponding PI control designs in which the error in the past may badly affect to the current steady-state operation points and may cause some disturbances for other control purposes.

• Journal of Power System Engineering
• /
• v.3 no.1
• /
• pp.67-73
• /
• 1999

It is not easy to control the speed of AC motors accurately without modeling with some parameters for the controlled system. However, there are some application parts which do not require high speed responses strictly and the motor parameters can not to be identified simply. In this paper, a speed control method for a synchronous motor(S.M) with unknown parameters of the motor is investigated. The method is based on the current control algorithm. Speed controller and current controller are designed using PI control law. Some experiments are performed using DSP and power expert system to prove the validity of the proposed method. Throughout experimental results, the method is confirmed successfully. This method is expected to control the system with unknown parameters of the S.M efficiently.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.5
• /
• pp.690-697
• /
• 2012

Novel 8/10 bearingless switched reluctance motor, which can control rotor radial positions with magnetic force, is proposed. The motor has combined characteristics of switched reluctance motor and magnetic bearing. This paper proposes a air-gap control system method of suspending force control in a bearingless switched reluctance motor (BLSRM). The proposed radial force control scheme is independent to the torque winding current. A PI direct current control (DCC) controller and look-up table are used to maintain a constant rotor air-gap. From the analysis and the experimental results, it is shown that the proposed strategy is effective in realizing a naturally decoupled radial force control of BLSRM.

• Proceedings of the KIPE Conference
• /
• 2014.11a
• /
• pp.203-204
• /
• 2014

In this paper, single-phase uninterruptible power supply design method is presented. In this control scheme, input current, output current and output voltage are used. For voltage control PR controller is used and that for current controller is PI controller. The gains for controllers are sought by the classical method for determining gains. Throughout simulations the performance of single-phase UPS is verified.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1248-1250
• /
• 2000

The aim of this paper is to present a review of recently used current control technique for three-phase voltage source pulse-width modulated converters. Various technique, different in concept, three current control methods are presented in this paper. Current -control methods to be applied in system are PI controller. Predictive current controller. Minimum-time current controller respectively. In initial state and transient state, the response characteristics of three current control methods are verified through simulations.

• Proceedings of the KIPE Conference
• /
• 2016.11a
• /
• pp.65-66
• /
• 2016

이 논문은 자성체 주변에 자기장과 자기장 기울기를 형성하여 자성체의 위치와 각도를 제어하는 자기장 제어 시스템을 위한 제어법을 제안한다. 자기장 제어 시스템을 구성하는 각 코일은 전류 제한 아래 동작하게 되는데 만약 각 코일이 독립적으로 제한되는 경우 합성된 자기장이 주어진 지령과 달라져 자성체의 정렬 및 병진운동 방향이 잘못 제어될 수 있다. 이 논문은 이를 방지하여 방향 우선 제어를 수행하기 위한 비례 전류 지령 보정법을 제안한다. 이와 함께 전압 제한으로 인해 발생할 수 있는 자성체의 과도기 방향 제어 오류를 방지하기 위한 PI 전류제어기 이득 설정 방법을 제안한다. 제안된 전류 지령 보정법의 유효성은 실험을 통해 확인되었다.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1114-1116
• /
• 2000

A direct model reference adaptive control (DMRAC) is applied to the speed control of brushless do(BLDC) motor. The main objective is to achieve precise speed control in the face of varying motor parameters and load. The control is described as an outer loop speed control and an inner current loop control which has raster dynamics than the speed loop. The adaptive control is applied to the outer speed control loop. DMRAC is compared to an indirect adaptive controller(IMRAC) and a PI controller. Simulation results show that the two adaptive controllers give similar respose and are superior to the PI controller. However, the DMRAC algorithm is simpler to implement.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.32B no.9
• /
• pp.1239-1246
• /
• 1995

A forced commutated cycloconverter (FCC) is a direct ac-ac converter capable of providing simultaneous voltage and frequency transformations. In this paper, vector control of an induction motor controlling stator current with forced commutated cycloconverter is presented. The advantage of current control is that the stator dynamics are eliminated and high performance vector control can be achieved. A novel modulation method based on dq transformation techniques is presented. Proposed modulation strategy generates the low frequency modulation function by the instantaneous value of the desired output voltages not by the steady state values of output magnitude and output frequency. PI control and predictive control algorithm for current control are applied, and the validity of proposed method is confirmed through digital simulations. Simulation results of step response and torque distubance and current control are presented.