• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.436-439
• /
• 2007

This paper describes the optimization of PGS(Patterned Ground Shield) of 5.5 turns rectangular spiral inductor using Taguchi's method. PGS is decrease method of parasite component by silicon substrate among dielectric loss reduction method. By using the taguchi's method, each parameter is fixed upon that PGS high poison(A), slot spacing(B), strip width(C) and overlap turn number(D) of PGS design parameter. Then we verified that percentage contribution and design sensitivity analysis of each parameter and level by signal to noise ratio of larger-the-better type. We consider percentage contribution and design sensitivity of each parameter and level, and then verify that model of optimization for PGS is lower inductance decreasing ratio and higher Q-factor increasing ratio by EM simulation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.2
• /
• pp.363-368
• /
• 2009

In the paper, we confirmed improvement Noise figure of the entire RF front-end using spiral inductor with PGS(Patterned Ground Shield) and current bleeding techniques. LNA design is to achieve simultaneous noise and input matching. Spiral inductor in input circuit of LNA inserted PGS for betterment of Q-factor. we modeling inductor using EM simulator, so compared with inductor of TSMC 0.18um. We designed and simulation the optimum structure of PGS using Taguchi's method. We confirmed enhancement of noise figure at LNA after substituted for inductor with PGS. Mixer designed using current bleeding techniques for reduced noise. We designed LNA using inductor with PGS and Mixer using current bleeding techniques, so confirmed improvement of noise figure.

• 한국정보통신설비학회:학술대회논문집
• /
• 2008.08a
• /
• pp.35-38
• /
• 2008

In this paper, study noise performance of LNA to enhance Q-factor of input circuit by patterned ground shield is inserted inductor using TSMC 0.18um. Applied LNA technology is cascode method. The input matching circuit was constituted on-chip and wirebonding inductor. Taguchi's method is used for the best suited structure of PGS. We confirmed enhancement of Q-factor by inserted PGS into inductor. The input matching circuit enhanced Q-factor by inductor with PGS improve noise figure of LNA.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.272-273
• /
• 2007

This paper presents the characteristic of rectangular and octagonal spiral inductor using PGS(Patterned Ground Shield). We investigated variation of inductance and Q-factor with changing of turn number at fixed width, spacing and inner diameter. We confirmed that characteristic of inductance and Q-factor be appled PGS in rectangular and octagonal types spiral inductor by EM simulation tool. Inductance decreased irrespective of structure but Q-factor increased. When PGS not exist, Q-factor of Inductor is analogous at classification frequency but, rectangular is a few larger then octagonal in small turn number. The other side, When PGS is inserted, we confirmed that octagonal lager then rectangular in many turn number. Q-factor is improved in case of octagonal structure and small turn number by PGS effect.

• Journal of Biosystems Engineering
• /
• v.41 no.3
• /
• pp.145-152
• /
• 2016

Purpose: This study aims to establish the effect of pinhole position errors in the planet carrier of a planetary gear set (PGS) on load sharing among the planet gears in the hydromechanical transmission (HMT) system of an agricultural tractor. Methods: A simulation model of a PGS with five planet gears was developed to analyze load sharing among the planet gears. The simulation model was verified by comparing i ts r esults w ith those of a model developed in a previous s tudy. The verified simulation model was used to analyze the load-sharing characteristics of the planet gears with respect to the pinhole position error and the input torque to the PGS. Results: Both simulation models had identical load magnitude sequences for the five planet gears. However, the load magnitudes on the corresponding planet gears differed between the models because of the different stiffnesses of the PGS components and the input torques to the PGS. The verified simulation model demonstrated that the evenness of load sharing among the planet gears increases with decreasing pinhole position error and increasing input torque. Conclusions: The geometrical tolerance of the pinhole position should be properly considered during the design of the planet carrier to improve the service life of the PGS and load sharing among the planet gears.

• Proceedings of the KIEE Conference
• /
• 2008.10a
• /
• pp.107-108
• /
• 2008

This article describes optimization for PGS(Patterned Ground Shield) of rectangular spiral inductor using Taguchi's Design of Experiment. PGS is decrease method of parasite component by silicon substrate among dielectric loss reduction method. Using taguchi's design of experiment, each parameter is fixed upon that PGS high poison(A), slot spacing(B), strip width(C) and overlap turn number(D) of PGS design parameter. Then we verified that percentage contribution and design sensitivity analysis of each parameter and level by signal to noise ratio of larger-the-better type. We consider percentage contribution and design sensitivity of each parameter and level, and then verify that model of optimization for PGS is lower inductance decreasing ratio and higher Q-factor increasing ratio by EM simulation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.6
• /
• pp.964-973
• /
• 2008

In this study, a short-wavelength coplanar-type transmission line employing periodic ground structure (PGS) was developed for application to miniaturized on-chip passive component on Si Radio Frequency Integrated Circuit (RFIC). The transmission line employing PGS showed shorter wavelength and lower characteristic impedance than conventional coplanar-type transmission line. The wavelength of the transmission line employing PGS structure was 57 % of the conventional coplanar-type transmission line on Si substrate. Using the theoretical analysis. basic characteristics of the transmission line employing PGS (e.g., bandwidth. loss, impedance, and resonance characteristics) were also investigated in order to evaluate its suitability for application to a development of miniaturized passive on-chip components on silicon RFIC. According to the results. the bandwidth of the transmission line employing PGS was more than 895 GHz as long as T is less than 20${\mu}m$, and the resonance characteristic was observed in 1239 GHz, which indicates that the PPGM structure is a promising candidate for application to a development of miniaturized on-chip passive components on Si RFIC.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.8
• /
• pp.2854-2874
• /
• 2015

This paper presents a game theoretic approach to analyze the public goods (PGs) allocation in peer-to-peer (p2p) networks. In order to reduce the free-riders and promote the cooperation among peers, we propose an incentive mechanism with cooperation-based game theory. In this paper, we regarded the contributed resources by cooperators as public goods (PGs). We also build the PGs allocation in P2P networks to be the optimization problem, and the optimal solution of PGs allocation satisfies the Bowen-Lindahl-Samuelson equilibrium. Firstly, based on the subscriber mechanism, we analyze the feasibility and prove the validity, which can achieve Nash equilibrium. However, this strategy cannot meet to Bowen-Lindahl-Samuelson equilibrium as the free-riders do not pay with their private goods for consuming the PGs. Secondly, based on the Walker mechanism, we analyze the feasibility and prove the validity for the same allocation problem, which meets to Bowen-Lindahl-Samuelson equilibrium and achieves Pareto efficiency within cooperative game. Simulations show that the proposed walker mechanism can significantly improve the network performance of throughout, and effectively alleviate free-riding problem in P2P networks.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.4
• /
• pp.245-252
• /
• 2016

Girth gears are applied in the mining, cement, and mineral processing industries and used in various types of horizontal mills, rotary dryers and kilns, and other heavy-gear ring applications. The large ring gears are normally fitted outside mills or kilns to provide the primary rotational drive. Recently, an external pinwheel gear set (e-PGS) was introduced to overcome manufacturing problems associated with girth gears. e-PGS is also suitable for low-speed, heavy-duty mechanical transmission and dusty and poor-lubrication conditions. This paper first presents a new profile modification of root relief for the e-PGS cam pinion. We then investigate load-stress factors to estimate the surface fatigue life by varying the shape design parameters. The results show that the contact fatigue life of an e-PGS can be extended significantly by increasing the profile shift coefficient. However, support bearing life of the pinwheel depends more on the contact force distribution than the profile shift coefficient.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.2
• /
• pp.231-237
• /
• 2015

The pin-gear drive is a special form of fixed-axle gear mechanism. A large wheel with cylindrical pin teeth is called a pinwheel. As pinwheels are rounded, they have a simple structure, easy processing, low cost, and easy overhaul compared with general gears. They are also suitable for low-speed, heavy-duty mechanical transmission and for occasions with more dust, poor lubrication, etc. This paper introduces a novel slewing ring bearing with an external pinwheel gear set (e-PGS). First, we consider the exact cam pinion profile of the e-PGS with the introduction of a profile shift. Then, the contact stresses are investigated to determine the characteristics of the surface fatigue by varying the shape design parameters. The results show that the contact stresses of the e-PGS can be lowered significantly by increasing the profile shift coefficient.