• Korean Journal of Materials Research
• /
• v.15 no.7
• /
• pp.465-472
• /
• 2005

Preparation of copper film on PET substrate was carried out by cyclic operation of RF-magnetron­sputtering under continuous operation of ECR-CVD. The purpose of this study is aimed to an increase in deposition rate with keeping excellent adhesion between copper film and PET. In order to optimize the sputtering time under continuous ECR-CVD, cyclic operation concept is employed. By changing parameters of cyclic operation such as split of e and cycle time of A, the characteristics and thickness of the deposited copper film are controlled. As $\theta$ value increase, film thickness could confirm to increase and its surface resistivity value decreases. The highest adhesive strength appears at $\theta=0.33$ and cycle time of 30 min. The uniformity of copper film shows $5\%$ in our experimental range.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1262-1263
• /
• 2008

Recently film-typed dye sensitized solar cell(DSC) attracts much attention with increasing applications for its flexibility and transparency. The ZnO:Al thin film, which serves mainly as transparent conducting electrode, Aluminium-doped zinc oxide(ZnO:Al) thin film has emerged as one of the most promising transparent conducting films since it is inexpensive, mechanically stable, and highly resistant to deoxidation. In this paper ZnO:Al thin film was deposited on the polyethylene terephthalate(PET) substrate by the capacitively coupled r. f. magnetron sputtering method. The effects of gas pressure and r. f. discharge power on the morphological, electrical and optical properties of ZnO:Al thin film were studied. Especially the variation in substrate thickness after sputtering and surface morphology of the substrate were investigated and clarified. The results showed that the film deposited on the PET substrate at r. f. discharge power of 180 W showed the minimum resistivity of about $1.5{\times}10^{-3}{\Omega}-cm$ and a transmittance of about 93%.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.1
• /
• pp.21-25
• /
• 2009

Using an evaporation system, $SiO_2$ was deposited as a buffer layer between a PET substrate and a ITO layer and then ITO/$SiO_2$/PET layers were annealed for 1.5 hours at the temperature of $180^{\circ}C$. Adhesion and electro-optical properties of ITO films were studied with thickness variance of a $SiO_2$ buffer layer. As a result of introduction of the $SiO_2$ buffer layer, sheet resistance and resistivity increased and a ITO film with optimum sheet resistance ($529.3{\Omega}/square$) for an upper ITO film of resistive type touch panel could be obtained when $SiO_2$ of $50{\AA}$ was deposited. And it was found that ITO films with $SiO_2$ buffer layer have higher transmittance of $88{\sim}90%$ at 550 nm wavelength than ITO films with no buffer layers and the transmittance was enhanced as $SiO_2$ thickness increased from $50{\AA}$ to $100{\AA}$. Adhesion property of ITO films with $SiO_2$ buffer layers became better than ITO films with no buffer layers and this property was independent of $SiO_2$ thickness variance ($50{\sim}100{\AA}$). By depositing a $SiO_2$ buffer layer of $50{\AA}$ on the PET substrate and sputtering a ITO thin film on the layer, a ITO film with enhanced adhesion, electro-optical properties could be obtained.

• Korean Journal of Optics and Photonics
• /
• v.30 no.4
• /
• pp.159-166
• /
• 2019

The trajectory of the transmission ellipsometric pseudoconstant ${\rho}=tan{\psi}_{\mu}e^{i{\Delta}_{\mu}}$ of a uniaxially anisotropic substrate like PET forms a circle in polar coordinates, as the phase-retardation angle is varied at a fixed azimuthal angle. The radius as well as the center's position of this circle are functions of the azimuthal angle only. This circle passes through the point (1,0), and the center of this circle is located on the real axis. These characteristics of the circle are examined analytically, and are utilized to derive simple expressions for the azimuthal angle and the phase-retardation angle of the uniaxially anisotropic substrate using the measured transmission ellipsometric constant. Finally, we confirm that the derived expressions are well applied to the analysis of the optical anisotropy of a PET film.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.221-221
• /
• 2014

The current energy crisis in many countries has led to the search of an efficient renewable energy source. Among those the solar energy is the most abundant and easily available. However harvesting the solar energy requires a much efficient device. Lot of research has been done in this regard and so far the efficiency of traditional solar cell stands around ~50% and for PET films it is much lesser. The potential application of PET films in the solar cells can be very promising provided the fact that the PET film is lighter and logistically more viable. There is a lot of work that is being done to increase the efficiency of PET based solar cells. The base electrode plays a vital role in increasing the efficiency of the cell.

• Journal of the Semiconductor & Display Technology
• /
• v.8 no.2
• /
• pp.49-53
• /
• 2009

The oxygen barrier films were formed on poly(ethylene terephthalate) (PET) substrate by a sol-gel process using 3-aminoproprytrimethoxysilane (APTMOS). The effects of solvent type, coating times and incorporation of fumed silica on oxygen permeability coefficient were investigated. The APTMOS coating film prepared from methanol as a solvent exhibited higher oxygen barrier properties than that using THF. The oxygen permeability coefficient of coated film with APTMOS/methanol by coating 7 times was measured to be $2.28{\times}10^{-6}$, while that of PET film was $1.16{\times}10^{-4}$ GPU. The addition of fumed silica does not affect the oxygen barrier properties. It may be explained that silica particles disrupt chain packing, which leads to an increase in free volume for permeation.

• Journal of Information Display
• /
• v.2 no.1
• /
• pp.38-42
• /
• 2001

Thin films of $In_2O_3-SnO_2$(ITO), $SnO_2$, and $SiO_2$ were prepared on the PET substrate by DC magnetron roll sputtering. 135 nm thick ITO film on $SiO_2$/PET substrate has sheet resistance as low as 55 ${\Omega}/square$ and transmittance as high as 85%. $H_2O$gas permeation through the film was 0.35 g/$m^2$ in a day. These properties are enough on optical film for the plastic LCD substrate or touch panel. Both refractive index and sheet resistance of ITO was found to be very sensitive to $O_2$ flow rate. Oxygen flow conditions have been optimized from 4 to 5 SCCM at $10^{-3}$torr. It is also shown that both thickness of $SnO_2$ and refractive index of $SiO_2$ decrease as $O_2$ flow rate increases.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.12
• /
• pp.13-18
• /
• 2005

In this paper, we fabricated a pixel array in which each pixel was consisted of Organic Thin Film Transistor (OTFT) serially connected with Organic Light Emitting Diode (OLED) on Poly-ethylene-terephthalate (PET) substrate and the number of pixels was 64 x 64. As a gate insulator of OTFT, the thermally cross-linked PVP was used and the organic semiconductor, Pentacene, is deposited for an active layer of OTFT considering the compatibility with PET substrate. The mobility of OTFT is $1.0\;cm^2/V{\cdot}sec$ as a discrete device, but it was reduced to $0.1\~0.2\;cm^2/V{\codt}sec$ in the array. We analyzed the operation of the array and confirmed the current driving ability of OTFTs for the OLEDs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.380-381
• /
• 2007

This paper reports on the deposition conditions and properties of ITO films used as electrode layer in a organic light emitting diodes on a PET substrate. The deposition technique employed was specially designed roll-to-roll sputtering. The oxide was deposited at room temperature in an argon and oxygen plasma on a transparent conducting ITO layer on a PET film. The influence of deposition parameters such as DC power, working pressure and oxygen partial pressure has been investigated, in order to obtain the best compromise between a high deposition rate and adequate electro-optical properties. Electrical and optical properties of ITO films were analyzed by Hall measurement examinations with van der pauw geometry at room temperature and UV/Vis spectrometer analysis, respectively. In addition, the structural properties and surface smoothness were measured by x-ray diffraction and scaning electron microscopy, respectively. From optimized ITO films grown by roll-to-roll sputter system, good electrical$(6.44{\times}10^{-4}\;{\Omega}-cm)$ and optical(above 86 % at 550 nm) properties were obtained. Also, the ITO films exhibited amorphous structure and very flat surface beacause of low deposition temperature.

• Journal of the Korean Ceramic Society
• /
• v.52 no.4
• /
• pp.264-268
• /
• 2015

Cu films were plated in an eco-friendly electroless bath (No-Formaldehyde) on Ni/screen printed Ag pattern/PET substrate. For electroless Cu plating, we used sodium-phosphinate ($NaH_2PO_2{\cdot}H_2O$) as reducing agent instead of Formaldehyde. All processes were carried out in electroless solution of pH 7 to minimize damage to the PET substrate. According to the increase of sodium-phosphinate, the deposition rate, the granule size, and rms roughness of the electroless Cu film increased and the Ni content also increased. The electroless Cu films plated using 0.280 M and 0.575 M solutions of sodium-phosphinate were made with Cu of 94 at.% and 82 at.%, respectively, with Ni and a small amount P. All electroless Cu plated films had typical FCC crystal structures, although the amount of co-deposited Ni changed according to the variation of the sodium-phosphinate contents. From these results, we concluded that a formation of higher purity Cu film without surface damage to the PET is possible by use of sodium-phosphinate at pH 7.