• Korean Journal of Food Science and Technology
• /
• v.46 no.6
• /
• pp.739-742
• /
• 2014

This study investigated the effect of perforation by the Indian meal moth (Plodia interpunctella) larvae on various flexible food-packaging films, in relation to their thickness and type. Among the various flexible packaging films, polyethylene (PE), aluminum foil (AF), polypropylene (PP), polystyrene (PS), and polyethylene terephthalate (PET) were selected for this study due to their wide usage in food packaging. Based on their thickness, film penetration by P. interpunctella larvae was measured as in following order: PP, $20{\mu}m$; AF, $9{\mu}m$; PET, $12{\mu}m$; PP, $30{\mu}m$; PS, $30{\mu}m$; PE, $40{\mu}m$; PE, $35{\mu}m$; PS, $60{\mu}m$; and PET, $16{\mu}m$. P. interpunctella larvae rapidly penetrated through the packaging films regardless of their thickness and type. In particular, it was observed that PP of $20{\mu}m$ and PS of $30{\mu}m$ were completely penetrated by P. interpunctella larvae within 72 h, rendering thin PP and PS films less valuable as anti-insect packaging films. Our results show that the perforations by P. interpunctella larvae were observed in the thin films. These results imply that each packaging film has a marginal thickness against the perforations by P. interpunctella larvae.

• Journal of Mushroom
• /
• v.22 no.1
• /
• pp.31-36
• /
• 2024

Plastics are widely used in industries in human society and because of their structural stability, degradation is a serious global issue. To estimate the degradation of plastic, 31 edible mushrooms were cultured with the selected plastic films (polyethylene [PE], polystyrene [PS], and poly(ethylene terephthalate) [PET]) for 3 months at 25 ℃. Measuring the weight of the films showed that four species of mushrooms, namely Porostereum spadiceum, Ganoderma lucidum, Coprinellus micaceus, and Pleurotus ostreatus, exhibited the highest degrees of plastic degradation. In addition, the mushrooms and fungi that exhibited the most significant plastic degradation were cross-cultured to promote this degradation. As a result, cross-cultivation of G. lucidum and Aspergillus niger showed a weight loss of 2.49% for the PET film. For the PS film, Aspergillus nidulans showed a weight loss of 4.06%. Cross-cultivation of A. nidulans and C. micaceus, which showed a weight loss of 2.95%, was noted as an alternative for PS biodegradation, but is harmful to humans. These bio-degradation effects of edible mushroom will contribute to the development of alternatives for eco-friendly plastic degradation.

• Journal of the Korean Vacuum Society
• /
• v.21 no.4
• /
• pp.205-211
• /
• 2012

We investigated the optical and hydrophobic properties of the deposited silver (Ag) zinc oxide (ZnO) nanorods (NRs) on flexible indium tin oxide (ITO) coated polyethylene terephthalate (PET) substrates (i.e., ITO/PET). The ZnO NRs were grown by an electrochemical deposition using a sputtered ZnO seed layer and the Ag was deposited by using a thermal evaporator. For comparison, the same fabrication process was carried out on the bare ITO/PET without ZnO NRAs. Due to the discrete surface of ZnO NRs, the deposited Ag was formed as nano-scale particles, while the Ag became film-like for bare ITO/PET. In order to control the size and amount of Ag particles, the Ag deposition time was changed from 100 to 600 s. When the deposition time was increased, the Ag particles became larger and denser, and the absorptance was increased. This enhanced absorptance may be due to the localized surface plasmon resonance of Ag particles. Furthermore, the relatively high hydrophobicity was observed for the deposited Ag on the ZnO NRs/ITO/PET. These improved optical and surface properties are expected to be useful for flexible photovoltaic and optoelectronic devices.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1798-1802
• /
• 2007

Adhesion strength of single layer ceramic capacitor sheet was measured using a peel testing system developed in this study. The peel test specimens with various dimensions were prepared from the ceramic sheet cast on the PET film. In peel test, the sheet specimen was adhered on the glass jig floating on the liquid media, which was designed to minimize the friction, and the specimen was then pulled up by micro-actuator. During the separation of the sheet from the PET film, peel force was measured. To normalize the testing condition, 3 different widths of the specimen were selected: 5, 10 and 20 mm. was used Furthermore, testing speed effect was investigated in this study. From the resullts using various testing conditions, the standard method for the peel strength testing may be suggested. Based on the testing condition, effect of peel angle on the strength was experimentally examined. It was found that the adhesive strength for the ceramic sheet is nearly identical, irrespective of the specimen width ranged from 5 to 20 mm, while the adhesive strength was increased with increasing testing speed. Furthermore, the strength was shown to be dependent on the peel angle.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.3
• /
• pp.207-214
• /
• 2001

The conductive polymers, polyaniline (PANI) emeralidin base and 3,4-polyethylene dioxythiophene(PEDOT) were synthesized and coated on the PET film dealt with acryl type primer to study the electromagnetic shielding effectiveness. When both PANI and PEDOT were coated on the PET film dealt with acryl type priemer, their surface properties such as he adhesive increased. For PANI, when blended with the binder such as PMMA, it adhesive and surface hardness increased, too. The visible light transmittance decreased, while the electromagnetic shielding effectiveness increased, when coated thickness of PANI and PEDOT increased. For PANI, the electromagnetic shielding effectiveness increased as its surface resistance decreased. For PANI, when the surface resistance was 140 Ω/$\square$, the shielding effectiveness was found to be 11 dB in the far field, and 13 dB in the near field at 1 GHz. For PEDOT, when the surface resistance was 200 Ω/$\square$, the shielding effectiveness was found to be 3 dB in the far field, and 7dB in the near field.

• Polymer(Korea)
• /
• v.38 no.6
• /
• pp.720-725
• /
• 2014

Aminopropyl terminated polydimethylsiloxane was synthesized by hydrosilylation reaction with hydride terminated polydimethlysiloxane and allyl amine. Polydimethylsiloxane modified urea with isocyanate group was prepared from cyclic trimer of hexamethyldiisocyanate with aminopropyl terminated polydimethylsiloxane. Polydimethylsiloxane modified urea/acrylate resin (PUA) was prepared from the urethane reaction of PU with isocyanate group and 2-hydroxyethylmethacrylate. PUA structure was analyzed by FTIR and NMR. Coating materials were prepared by mixing PUA, acrylic monomer, photo-initiator, and solvent and coated on PET film to obtain flexible hard coating film by UV irradiation.

• Journal of Surface Science and Engineering
• /
• v.42 no.6
• /
• pp.276-279
• /
• 2009

ITO and ITO:Ce films were deposited by DC magnetron sputtering using an ITO ($SnO_2$: 10 wt%) and $CeO_2$ doped ITO ($CeO_2$: 0.5, 3.0, 4.0 and 6.0 wt%) ceramic targets, respectively, on unheated polyethylene terephthalate (PET) substrates. The lowest resistivity $6.7{\times}10^{-4}{\Omega}cm$ was obtained from ITO:Ce film deposited using $CeO_2$ (3.0 wt%) doped ITO target. On hte other hand, ITO:Ce (0.5wt%) film has the excellent mechanical durability which was evaluated by bending test. This result was attributed to the higher binding energy of $CeO_2$ compared to $SnO_2$ and $In_2O_3$. Therefore, $CeO_2$ atoms have a small displacement caused by the bombardment of high energy particles, and it attribute to the increase in adhesion caused by decrease in internal stress. The average transmittance of the films was more than 80% in the visible region.

• Textile Coloration and Finishing
• /
• v.1 no.1
• /
• pp.7-18
• /
• 1989

The distinguishing characteristic of the glow discharge is that chemical reaction induced by partially ionized gases are limited only to the substrate surface. Most studies have been done on the plasma etching and polymerization. The graft polymerization in vapour phase by cold plasma has been rarely investigated. In this study the system of tub3ar reaction chamber with capacitively coupled electrode of alternative current of 60 Hz was employed for the graft polymerization. The graft polymerization of Acylic Acid(AA) onto the poly (ethylene terephthalate) (PET) was carried out by treatment of PET film and fabric by cold plasma (glow discharge of argon gas), followed by the supply of AA vapour. The graft yield was about 1 wt%. The surface property was determined by contact angle, the surface tension was evaluated by zisman’s plot and equation of surface tension mesurement. The results were as follows: 1. In order to obtain lower contact angle, it was effective to avoid the vicinity of electrodes for a setting position of substrate. 2. Contact angle affected on the monomer pressure and its duration of exposure to the acid vapour. 3. Polymer radical formation was influenced by the changes of the value of current density and plasma treatment time. 4. Total surface tension of plasma grafted PET film increased. With an increase in the carboxylic acid content, the dispersion force decreased, while, the polar force and hydrogen bonding force increased. 5. The contact angle decreased from $75^\circ$ to around $30^\circ$ by plasma grafting. There was no ageing effect on the contact angle after 4 months.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.81-83
• /
• 2000

Tin-doped indium oxide(ITO) thin films were deposited on polyethylene terephthalate(PET) at room temperature by oxygen ion beam assisted evaporator system and the effects of oxygen gas flow rate on the properties of room temperature ITO thin films were investigated. Plasma characteristics of the ion gun such as oxygen ions and atomic oxygen radicals as a function of oxygen flow rate were investigated using optical emission spectroscopy(OES). Faraday cup also used to measure oxygen ion density. The increase of oxygen flow rate to the ion gun generally increase the optical transmittance of the deposited ITO up to 6sccm of $O_2$ and the further increase of oxygen flow rate appears to saturate the optical transmittance. In the case of electrical property, the resistivity showed a minimum at 6 sccm of $O_2$ with the increase of oxygen flow rate. Therefore, the improved ITO properties at 6 sccm of $O_2$ appear to be more related to the incorporation of low energy oxygen radicals to deposited ITO film rather than the irradiation of high energy oxygen ions to the substrate. At an optimal deposition condition, ITO thin films deposited on PET substrates showed the resistivity of $6.6{\times}10^{-4}$ ${\Omega}$ cm and optical transmittance of above 90%.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.13 no.3
• /
• pp.110-122
• /
• 2009

Purpose: Nowadays, A medical institution assesment could get more interest about a quality of medical services from many hospitals that developed the active activities for improving medical services. Also, there is an other additional issue which is the patients risk management. Uijeongbu ST. Mary's hospital Nuclear Medicine department has been changed many work process after PET-CT introduction and renovation of its place since 2008. Therefore, modified structure and the way of existing work process have contained risk factors. The purpose of this study would be the appropriate risk management process while imaging examination process, the removal risk factors and improved activities through the analysis risk factors. Materials and Methods: Nuclear Medicine department new process should analysis through many-sided, Firstly, make and trained risk management manual after then apply an actual work. Result analysis showed the number of risk accident occurrence that comparing the last year and after the improved activities. Secondly, producing risk management public relations film has been showed an applicable patient after then the customer service measurement checked for a hundred patient by questionnaire. Lastly, Risk factors were eliminated through the facilities participation improving activities which could change for the better risk factors. Results: The number of safety accident occurrence(medication error, fall and collision) were checked as zero after the improving activities both PET-CT and gamma camera examination. The results of questionnaire showed as follows; 74% marked as understanding of the test process and 81% checked "satisfaction" after the public relations film showing. The question "Did you consider about the risk factors?", both PET-CT and gamma camera checked as 94% and 89% respectively. Customer risk management could be accomplished effectively through the improving activities at the nuclear medicine department. Conclusions: The study would be an opportunity that spread risk factors were systematically showed and analyzied. Also, It showed the possibility of the minimized safety accident and its feedback, if application of the response manuel that could be a standard of radiology technician's work method to react safety accident. It was the more effective that visual material could be easy to approach as a methodology of risk factors. As far as I have concerned that It could help the safety and convenience through continuous and detailed activities that offer to patients.