• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.121.2-121.2
• /
• 2014

Synthesis of catecholamine from aniline is achieved by plasma enhanced CVD process. Catecholamine has a variety of functions in body such as brain and bloodstream controls. Catecholamine also has an interesting property of a material independent ability of functionalizing surface, which is found at mussels' adhesive nature. Synthesis of catecholamine has only been available from DOPA by chemical reduction and oxidation. This study presents the direct synthesis of catecholamine from further elemental source, aniline, which has not been achieved by a conventional chemical method. The process also indicates that a variety of catecholamine can be formed by controlling reactant gases. In additional to PECVD's very useful properties such as conformal, ultrathin and uniform coatings, a direct synthesis from aniline and a capability of controlling formation of a variety catecholamine is believed to open up a numerous applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.171-174
• /
• 1994

The drive towards ultra-large-scale integrated circuits a continuous intermetal dielectric films for multi layer interconection. Optimum condition of remote plasma enhanced chemical vapour deposition(RPECVD) was achieved by orthogonal array method. Chracteristics of SiO$_2$ films deposited by using remote PECVD with N$_2$O gas were investigated. Etching rate of SiO$_2$ films in P-echant was about 6[A/s] that was the same as the thermal oxide. The films a showed high breakdown voltage of 7(MV/cm) and a resistivity of Bx10$\^$13/[$\Omega$cm] at 7(MV/cm). The interface Trap density of SiO$_2$ has been shown excel lent properties of 5x10$\^$10/[/$\textrm{cm}^2$eV]. It was observed that the dielectric constant dropped to a value of 4. 29 for 150 [W] RF power.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.2020-2022
• /
• 2002

SiC direct bonding technology is very attractive for both SiCOI(SiC-on-insulator) electric devices and SiC-MEMS fileds because of its application possibility in harsh environements. This paper presents on pre-bonding according to HF pre-treatment conditions in SiC wafer direct bonding using PECVD oxide. The PECVD oxide was characterized by XPS and AFM, respectively. The characteristics of bonded sample were measured under different bonding conditions of HF concentration and applied pressure, respectively. The bonding strength was evaluated by tensile strength method. Components existed in the interlayer were analyzed by using FT-IR. The bond strength depends on the HF pre-treatment condition before pre-bonding (Min : 5.3 kgf/$cm^2{\sim}$ Max : 15.5 kgf/$cm^2$).

• Proceedings of the KIEE Conference
• /
• 1990.07a
• /
• pp.180-182
• /
• 1990

Today, according to the temperature lowering of VLSI technology which have been required, the new thin film technology of low temperature have appeared. Plasma CVD method, one of low temperature technologies, have major problems with many interface trap defects. In this paper, we prepared ammonia free SiN film containing small H that acts as a defect impurity, and investigated the electrical properties of Laser assisted deposition film.

• Korean Journal of Materials Research
• /
• v.7 no.7
• /
• pp.582-586
• /
• 1997

본 연구에서는 플라즈마 화학 증착법으로 기판에 따른 DLC 박막의 접착력 변화를 조사하였다. 박막의 분리가 발생하기 시작하는 경우의 두께를 임계두께로 정하여 스크래치 테스터로 측정된 임계하중과 더불어 박막의 잡착강도값으로 사용하였다. 다이아몬드상 탄소박막은 실리콘 기판에서 가장 우수한 접착력을 가지는 것으로 나타났으며, 크롬>티타늄>철>세라믹 기판의 순으로 접착력이 감소하였다. XPS, AES 분석을 사용하여 계면에서 결합구조와 결합형태 등을 관찰하여 접착력과의 관계를 조사하였다. 그 결과 다이아몬드상 탄소박막의 접착강도는 막/기판의 계면에서의 탄화물 형성에 영향을 받으며, 계면에서의 초기산화물층에 큰 영향을 받는것을 확인하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2005.02a
• /
• pp.93-93
• /
• 2005

• Korean Journal of Materials Research
• /
• v.8 no.10
• /
• pp.890-897
• /
• 1998

The direct wafer bonding between n-InP(001) wafer and the ${Si}_3N_4$(200 nm) film grown on the InP wafer by PECVD method was investigated. The surface states of InP wafer and ${Si}_3N_4$/InP which strongly depend upon the direct wafer bonding strength between them when they are brought into contact, were characterized by the contact angle measurement technique and atomic force microscopy. When InP wafer was etched by $50{\%}$ HF, contact angle was $5^{\circ}$ and RMS roughness was $1.54{\AA}$. When ${Si}_3N_4$ was etched by ammonia solution, RMS roughness was $3.11{\AA}$. The considerable amount of initial bonding strength between InP wafer and ${Si}_3N_4$/InP was observed when the two wafer was contacted after the etching process by $50{\%}$ HF and ammonia solution respectively. The bonded specimen was heat treated in $H^2$ or $N^2$, ambient at the temperature of $580^{\circ}C$-$680^{\circ}C$ for lhr. The bonding state was confirmed by SAT(Scannig Acoustic Tomography). The bonding strength was measured by shear force measurement of ${Si}_3N_4$/InP to InP wafer increased up to the same level of PECVD interface. The direct wafer bonding interface and ${Si}_3N_4$/InP PECVD interface were chracterized by TEM and AES.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.2
• /
• pp.93-97
• /
• 2012

In this study, the fabrication and the characteristic analyses of OLED using in-situ passivation are investigated. OLEDs represent a disadvantage in decreasing its life due to the degradation caused by the penetration of moisture and oxygen. After the fabrication of OLED, an in-situ passivation method for inorganic thin films is developed. A process that uses PECVD method which can apply a vapor deposition process at room temperature is also developed. Changes in the degradation and electric characteristics of OLEDs are also analyzed by applying $SiO_2$ and SiNx thin films to OLED as a passivation layer. By applying the fabricated thin film to OLEDs as a passivation layer, the moisture penetration in a single layer film is ensured below $1{\times}10^{-2}\;g/m^2.day$. This leads to the improvement of such degradation characteristics in the application of multilayer films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.293-293
• /
• 2010

Carbon nanotubes (CNTs) have attracted considerable attention as possible routes to device miniaturization due to their excellent mechanical, thermal, and electronic properties. These properties show great potential for devices such as field emission displays, CNT based transistors, and bio-sensors. The metals such as nickel, cobalt, gold, iron, platinum, and palladium are used as the catalysts for the CNT growth. In this study, diamond-like carbon (DLC) was used for CNT growth as a nonmetallic catalyst layer. DLC films were deposited by a radio frequency (RF) plasma-enhanced chemical vapor deposition (RF-PECVD) method with a mixture of methane and hydrogen gases. CNTs were synthesized by a hot filament plasma-enhanced chemical vapor deposition (HF-PECVD) method with ammonia (NH3) as a pretreatment gas and acetylene (C2H2) as a carbon source gas. The grown CNTs and the pretreated DLC filmswere observed using field emission scanning electron microscopy (FE-SEM) measurement, and the structure of the grown CNTs was analyzed by high resolution transmission scanning electron microscopy (HR-TEM). Also, using energy dispersive spectroscopy (EDS) measurement, we confirmed that only the carbon component remained on the substrate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.8
• /
• pp.701-706
• /
• 2006

In addition to its similarity to genuine diamond film, diamond-like carbon (DLC) film has many advantages, including its wide band gap and variable refractive index. In this study, DLC films were prepared by the RF PECVD (Plasma Enhanced Chemical Vapor Deposition) method on silicon substrates using methane $(CH_4)$ and hydrogen $(H_2)$ gas. We examined the effects of the post annealing temperature on the structural variation of the DLC films. The films were annealed at temperatures ranging from 300 to $900^{\circ}C$ in steps of $200^{\circ}C$ using RTA equipment in nitrogen ambient. The thickness of the film and interface between film and substrate were observed by surface profiler, field emission scanning electron microscopy (FESEM), high resolution transmission electron microscopy (HRTEM), respectively. Raman and X-ray photoelectron spectroscopy (XPS) analysis showed that DLC films were graphitized ($I_D/I_G$, G-peak position and $sp^2/sp^3$ increased) ratio at higher annealing temperature. The variation of surface as a function of annealing treatment was verified by a AFM and contact angle method.