• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.403-405
• /
• 2006

Over the years, plasma display panel (PDP) manufacturers have impressed the flat panel display industry with yet another new product essentially having the merits of a larger screen size. Since larger size implies higher power ratings, voltage/current ratings of the power devices used have become a rising concern. Another important concern is the brightness of PDP, one way of increasing which is by operating the PDP at higher frequencies. In order to address the above issues, a transformer coupled sustain-driver for AC-PDP is proposed During the transition time, the two windings of the transformer greatly boost up the displacement current flowing through the panel capacitance and hence enable a fast inversion of the voltage polarity with practical values of resonant inductance. In the proposed topology, the resonant inductance can be increased by a factor of $(n+1)^2$ as compared to prior approaches. Increased inductance results in lower current stresses. Moreover, high frequency operation is possible by using higher value of n (turn ratio of the transformer). The operational principle and design procedure of the proposed circuit are presented with theoretical analysis. The validity of the proposed sustain driver is established through simulation and experimental results using a 42-in PDP

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.2
• /
• pp.45-50
• /
• 2013

This paper focuses on the fundamental issues for improving the efficiency and throughput of the AC PDP (Plasma Display Panel) manufacturing. The properties of the MgO protective layer affect the PDP efficiency. Especially, the secondary electron emission efficiency was affected on the deposition rate of MgO during the evaporation. In this study, the deposition rate of 5 $\AA$/s has given the maximum efficiency value of 0.05 It is demonstrated that the impurity gases such as $H_2O$, $CO_2$, CO or $N_2$, and $O_2$ can be remained inside the PDP panel before sealing and the amount of the impurity gases decreased rapidly as the base vacuum level increased, especially near $10^{-5}$ torr. The fundamental solution in order to overcome these problems is the vacuum in-line sealing process from the MgO evaporation to the final sealing of the panel without breaking the vacuum. We have demonstrated this fundamental process technology and shown the feasibility. The firing voltage was reduced down to 285 V at the base vacuum value of $10^{-6}$ torr, whreras it was about 328 V at the base vacuum value of $10^{-3}$ torr.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.1-5
• /
• 2002

The sustain driver for AC plasma display panel should provide alternating high voltage pulses to ignite plasma and recover the energy discharged from the intrinsic capacitance between the scanning and sustaining electrodes inside the panel. In this paper, an efficient sustain circuit employing boost-up function is proposed to achieve a faster rise-time in order to be suitable to widely used the address display period separated (ADS) driving method. The proposed circuit improves the recovery efficiency, regardless of the variation of the panel capacitance. The principle of operation, features, and simulated results are illustrated and verified on a 7.5-inch diagonal panel at 200 [kHz] operating frequency based on experimental prototype.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.2
• /
• pp.122-129
• /
• 2004

There is an increasing need for large flat panel display devices. PDP (Plasma Display Panel) is one of the most promising candidates for this need. Thermal shock failure of PDP glass during manufacturing process is a critical issue in PDP industry since it is closely related to the product yield and the production speed. In this study, thermal shock resistance of PDP glass is measured by water quenching test and an analysis scheme is described for estimating transient temperature and stress distributions during thermal shock. Based on the experimental data and the analysis results, a simple procedure for predicting the thermal shock failure of PDP glass is proposed. The fast cooling process for heated glass plates can accelerate the speed of PDP production, but often leads to thermal shock failure of the glass plates. Therefore, a design guideline for preventing the failure is presented from a viewpoint of high speed PDP manufacturing process. This design guideline can be used for PDP process design and thermal -shock failure prevention.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.04a
• /
• pp.26.1-26
• /
• 2003

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.3
• /
• pp.18-23
• /
• 2006

The formation degree of sustain (ITO pattern) determines the quality of a PDP (Plasma Display Panel). Thus, in the present study, we attempt to detect 100% of the defects that are larger than $30{\mu}m$. Currently, the inspection method in the PDP manufacturing process is dependent upon the naked eye or a microscope in off-line mode. In this study, a prototype inspection system for PDP ITO patterned glass is developed. The developed system, which is based on a line-scan mechanism, obtains information on the defects and sorts the defects by type automatically. The developed inspection system adopts a multi-vision method using slit-beam formation for minimum inspection time and the detection algorithm is embodied in the detection ability. Characteristic defects such as pin holes, substances, and protrusions are extracted using the blob analysis method. Defects such as open, short, spots and others are distinguished by the line type inspection algorithm. It was experimentally verified that the developed inspection system can detect defects with reliability of up to 95% in about 60 seconds for the 42-inch PDP panel.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.963-966
• /
• 2000

Plasma display panel (PDP) is a type of flat panel display utilizing the light emission that is produced by gas discharge. Barrier Ribs of PDP separating each sub-pixel prevents optical and electrical crosstalk from adjacent sub-pixels. Mold for forming barrier ribs has been newly researched to overcome the disadvantages of conventional manufacturing process such as screen printing, sand-blasting and photosensitive glass methods. Mold for PDP barrier ribs have stripes of micro grooves transferring stripes of glass-material wall. In this paper. Stripes of grooves of which width 48 um, depth 124um, pitch 274um was acquired by machining the material of WC with dicing saw blade. Maximum roughness of the bottom and sidewall of the grooves was respectively 120 nm, 287 nm. Maximum tilt angle caused by difference between upper-most width and lower-most width was 2$^{\circ}$. Maximum Radius of curvature of bottom was 7.75 ${\mu}{\textrm}{m}$. This results meets the specification for barrier ribs of 50 inch XGA PDP. Forming the glass paste will be followed by using mold in the near future.

• Journal of Information Display
• /
• v.9 no.3
• /
• pp.28-32
• /
• 2008

Low sustained voltage $(V_s)$ and high luminous efficiency (lumen/Watts) are required for the enhanced performance of an AC PDP. Both are not realized in the same condition, however, because luminous efficiency decreases when the sustained voltage is lowered in most cases. In this study, the three design factors in the front panel of a PDP, i.e., the thickness and position of the bus electrode and the thickness of the dielectric layer, were chosen to investigate how they affect the sustained voltage and the luminous efficiency, and to find a way to optimize them. Two values were given to each of the three design factors, and experiments were done via full factorial design, i.e., with a total of eight conditions, using a 3-in.diagonal test panel. The changes in the sustained voltage and the luminous characteristics were explained in connection with the discharge characteristics of the PDP cells.

• Journal of the Semiconductor & Display Technology
• /
• v.3 no.4
• /
• pp.1-4
• /
• 2004

21세기에 접어들면서 Digital시험방송의 시작과 다양한 Contents의 유입으로 평판디스플레이 (Flat Panel Display)에 관한 관심과 수요가 증가하고 있다. 이 중 PDP는 90년대 후반부터 양산 및 개발을 시작하여 현재는 40 inch에서 60 inch 화면 크기의 제품을 시장에서 구입할 수 있으며, 03년도에는 80 inch 크기의 Proto-type Model을 공개한 바 있다. PDP는 40 inch 이상의 대면적 구현이 용이하다는 점, CRT와 동등 수준의 화상 구현이 가능하다는 점, 제조공법이 간단하고 제조원가가 저렴하다는 점 등을 특징으로 시장을 확대하고 있으나, 좀 더 대중적인 디스플레이가 되기 위해서는 고휘도 및 고효율화, 화질개선 그리고 저가격화 등과 같은 과제를 해결하여야 한다. 본 논문에서는 PDP의 개발역사 및 시장현황, 구조 및 구동 방법 그리고 해결과제 및 전망에 대해서 포괄적으로 살펴보기로 한다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.99-102
• /
• 1999

A mixture which was made from organic gel, glass powder and ceramic powder was masklessly etched for fabrication of barrier rib of PDP(Plasma Display Panel) by focused Ar$^{+}$ laser( λ =514 nm) and Nd:YAG(λ =532, 266 nm) laser irradiation at the atmosphere. The depth of the etched grooves increases with increasing a laser fluence and decreasing a scan speed. Using second harmonic of Nd:YAG laser, the threshold laser fluence was 6.5 mJ/$\textrm{cm}^2$ for the sample of PDP barrier rib softened at 12$0^{\circ}C$. The thickness of 130 ${\mu}{\textrm}{m}$ of the sample on the glass was clearly removed without any damage on the glass substrate by fluence of 19.5 J/$\textrm{cm}^2$....