• Proceedings of the KIEE Conference
• /
• 1998.11b
• /
• pp.490-492
• /
• 1998

In this paper, fuzzy-PD control system is designed to control angle and position of the inverted pendulum. To optimize parameters of fuzzy-PD controller, we used adaptive evolutionary computation(AEC). AEC uses a Genetic A1gorithm(GA) and an Evolution Strategy(ES) in an adaptive manner in order to take merits of two different evolutionary computations.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.2108-2111
• /
• 2005

The mission life of a satellite determines the amount of fuel required on-board, while the total mass requirement limits the fuel to be loaded. Hence, for the design of thruster control loop, not only the satellite pointing accuracy but the saving of fuel is to be considered. In this paper, a two-step fuzzy controller is proposed for the thruster control loop to save fuel consumption. This approach combines requirements for pointing control accuracy with minimum fuel consumption into a fuzzy controller design. To demonstrate this approach, we have designed a fuzzy controller for the Sun point Mode of KOMPSAT-2. The performance of this fuzzy controller design is compared with that of PD controller used for KOMPSAT-2.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.101.4-101
• /
• 2002

I. Introduction ▶The PID(Proportional-Integral-Derivative) controller is widely used in the industry it can be implemented easily for a typical second order plant. ▶The parameters of PID controller should be adapted complicatedly if a plant is various or the load is present. ▶For solving the problem, many control techniques have been developed. ▶A major method is a hybrid Fuzzy-PID controller. But, in case of using this method, we can not obtain characteristic of rapidly response and not achieved compensation on disturbance. ▶Therefore, we will use compensator fuzzy controller a front Hybrid type fuzzy-PID controller...

• 제어로봇시스템학회:학술대회논문집
• /
• 1995.10a
• /
• pp.71-74
• /
• 1995

In this paper, a new PID fuzzy controller(FC) based on parallel operation of PI and PD fuzzy control is presented. First, two fuzzy rule bases are constructed by separating the linguistic control rule for PID FC into two parts : one is e-.DELTA.e part, and the other is .DELTAL.$^{2}$e-.DELTA.e part. And then two FCs employing these rule bases indivisually are synthesized and run in parallel. The incremental control input is determined by taking weighted mean of the outputs of two FCs. The proposed PID FC improves the transient response of the system and gives better performance than the conventional PI FC.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1998.10a
• /
• pp.117-122
• /
• 1998

A servo system requires faster and more accurate dynamic reponses. Generally a PD control is mainly used to obtain the precision, and in the other hand a fuzzy control to improve the transient response and to cope with the nonlinearity of systems. Recently hybrid control, which is attempted to combine the advantages of PD control and a Fuzzy control was proposed, but this technique requires complicate design procedures. Therefore in this paper, designed on the Fuzzy controller with a various series rules, width of membership functions. And also it was showed to have the excellent adaptive performances against disturbances and the usefulness of this controller from the results of simulations.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.2 no.4
• /
• pp.1-6
• /
• 2005

This paper presents optimization of a pneumatic control system whose design parameters have been optimized so that the desired dynamic characteristics of cylinder position was obtained. The pneumatic system is used as transferring and stacking equipment for solid freeform fabrication system which has been widely used in design verification applications. The pneumatic system mainly consists of pneumatic control valves and cylinders. The system was modeled by using several principles for pneumatic components. The system was optimized to obtain dynamic performance with enough damping to reduce cylinder vibration. A fuzzy controller has been applied to fulfill the dynamic performance requirements of the pneumatic system. The simulation results show that the fuzzy controller is more effective than a PD controller.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1995.10b
• /
• pp.211-217
• /
• 1995

Conventional linear control fails to provide precise positioning of a control object under the influence of friction, deadzone, saturation, etc. This paper proposes a high-precision control scheme for a precise point-to-point positioning system, called an X-Y table, even under the same influences above. The proposed scheme is composed of a fuzzy precompensator and a PD controller. The fuzzy precompensator is employed to improve the performance of the PD controller. Its fuzzy rules are obtained from experimental evolutionary programming (EP), not from an expert. The effectiveness of the scheme is demonstrated by experiments on the X-Y table. with a positioning error of within 1$\mu\textrm{m}$.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.4
• /
• pp.73-81
• /
• 2003

DC series wound motor is commonly used for the industrial vehicles. Although it has good operating torque, heavy variations of parameters and nonlinear properties on friction and loads make it difficult to satisfy desired performance using conventional controllers. To solve this problem, fuzzy controller is proposed in this paper. The fuzzy controller has been designed based on the fuzziness of variables, it retains robustness even with nonlinearity.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.1
• /
• pp.60-67
• /
• 1998

In this paper, a gain scheduling method of PID controller is proposed using fuzzy logic for balancing control of an inverted pendulum. First, gains of PID controller are calculated using pole-placement technique for the linearized model of an inverted pendulum and these gains are modified by fuzzy logic throughout control operations. A PD controller is used by switching near the set-point to improve the performance. It is illustrated by simulations that the proposed hybrid fuzzy control method yidels smaller rising time and overshoot compared to the fixed-gain PID controller or fuzzy logic-based only PID controller.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.5
• /
• pp.598-603
• /
• 2004

An optical head actuator of an optical disk drive consists of two servo mechanisms for the focusing and the tracking to acquire data from disk. As the rotational speed of the disk grows, the utilized lag-lead-lead compensator has known to be above its ability for precisely controlling the optical head actuator. To overcome the difficulty, this paper propose a new controller design method for optical head actuator based fuzzy proportional-integral-derivative (PID) control and the genetic algorithm(GA). It employs a two-stage control structure with a fuzzy PI and a fuzzy PD control and is optimized by the GA to yield the suboptimal fuzzy PID control performance. It is shown the feasibility of the proposed method through a numerical tracking actuator simulation.