• Transactions of the Korean hydrogen and new energy society
• /
• v.16 no.1
• /
• pp.9-16
• /
• 2005

We studied the electrochromic properties of hydrated amorphous ruthenium oxide ($RuO_2{\cdot}xH_2O$) thin films using in-situ Raman spectroscopy during electrochemical charging/discharging cycles. We have found that the principal effect of hydrogen insertion into $RuO_2{\cdot}xH_2O$ is reduction of $Ru^{4+}\;to\;Ru^{3+}$, and not formation of new bonds involving hydrogen. We compared the changes in the Raman spectrum of a gasochromic $Pd/RuO_2{\cdot}xH_2O$ film as it is exposed to hydrogen gas with that of electrochemical hydrogen insertion. We tested the changes in the optical transmission of the $Pd/RuO_2{\cdot}xH_2O$ film when exposed to hydrogen gas.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.4
• /
• pp.101-106
• /
• 2008

The $SnO_2$ thin films doped with Pd and CNT as $NO_2$ gas sensor were prepared by spin coating and then the $NO_2$ gas response of these films were evaluated under $1ppm{\sim}5ppm\;NO_2$ concentration and operating temperature of $200^{\circ}C$. It was found that the sensor resistance was increased with $NO_2$ exposure and $NO_2$ concentration. The 3wt% Pd doped sample showed a sensitivity of 26.5 which was 10 times higher than that of pure $SnO_2$. And also the sensitivity of CNT doped sample increased with CNT content and it had 72 when 0.225 wt% of CNT was added under 5ppm $NO_2$ concentration.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.6
• /
• pp.248-256
• /
• 2012

A Pd-based hydrogen membranes for hydrogen purification and separation need high hydrogen perm-selectivity. The surface roughness of the support is important to coat the pinholes free and thin-film membrane over it. Also, The pinholes drastically decreased the hydrogen perm-selectivity of the Pd-based composite membrane. In order to remove the pinholes, we introduced various surface pre-treatment such as alumina powder packing, nickel electro-plating and micro-polishing pre-treatment. Especially, the micro-polishing pretreatment was very effective in roughness leveling off the surface of the porous nickel support, and it almost completely plugged the pores. Fine Ni particles filled surface pinholes with could form open structure at the interface of Pd alloy coating and Ni support by their diffusion to the membrane and resintering. In this study, a $4{\mu}m$ surface pore-free Pd-Cu-Ni ternary alloy membrane on a porous nickel substrate was successfully prepared by micro-polishing, high temperature sputtering and Cu-reflow process. And $H_2$ permeation and $N_2$ leak tests showed that the Pd-Cu-Ni ternary alloy hydrogen membrane achieved both high permeability of $13.2ml{\cdot}cm^{-2}{\cdot}min^{-1}{\cdot}atm^{-1}$ permation flux and infinite selectivity.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.11-12
• /
• 2012

In this paper, efficient visible light communication technology LED (Light Emitting Diode) lighting through the existing infrared sensor used for performance analysis of transmitting and receiving is possible. LED utilizes lighting by changing light into electricity. Lighting features while maintaining the basic principles of flashing LED and PD (Photo Diode) to send and receive communications from LED lighting communication convergence principle be realized simultaneously enabling. Multiple IT applications under the basic structure of LED technology development, and the current was encountered in real life. LED lighting anywhere with wireless communication technology that can, in order to ~ 1m above the initial value by taking advantage of the system H/W and infrared sensors(PD) are widely used in the entire system that can improve the speed of visible light data transmission system is finished. LED module that is used to communicate whether the performance analysis, For forecasting and communication distance on the LED and infrared sensor configuration of the implementation of the research is to study about the possibility of application methods and indicates.

• Journal of Environmental Science International
• /
• v.23 no.5
• /
• pp.763-770
• /
• 2014

The effect of $CO_2$ on the opening of stomata in the intact leaf of Commelina communis has been investigated. Full opening of stomatal apertures(around $18{\mu}m$) was achieved in the intact leaf by addition of $CO_2$($900{\mu}mol\;mol^{-1}$). At 90 minutes, the stomatal apertures of leaves treated with $CO_2$ free air were reduced. In contrast, stomata opened most widely with the treatment of $CO_2$ air at 90 minutes. The effects of light, $CO_2$ air and $CO_2$ free air on the change of membrane potential difference(PD) were measured. Fast hyperpolarization of guard cell membrane PD was recorded reaching up to -12 mV in response to light. If $CO_2$ free air was given firstly, there was no response. When light was given after $CO_2$ free air, the light effect was very clear. At the onset of $CO_2$ air, the PD showed a dramatic hyperpolarization to about -25 mV. Changes in the pH of apoplast in intact leaves in response to $CO_2$ air were observed. $CO_2$ air caused a change of 0.4 pH unit. Therefore, it can be hypothesized that $CO_2$ flowing could stimulate proton efflux which is a necessary precursor of stomatal opening.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.5
• /
• pp.345-350
• /
• 2018

Nanomaterials have considerable potential to solve several key challenges in various electrochemical devices, such as fuel cells. However, the use of nanoparticles in high-temperature devices like solid-oxide fuel cells (SOFCs) is considered problematic because the nanostructured surface typically prepared by deposition techniques may easily coarsen and thus deactivate, especially when used in high-temperature redox conditions. Herein we report the synthesis of a self-regenerated Pd metal nanoparticle on the perovskite oxide anode surface for SOFCs that exhibit self-recovery from their degradation in redox cycle and $CH_4$ fuel running. Using Pd-doped perovskite, $La(Sr)Fe(Mn,Pd)O_3$, as an anode, fairly high maximum power densities of 0.5 and $0.2cm^{-2}$ were achieved at 1,073 K in $H_2$ and $CH_4$ respectively, despite using thick electrolyte support-type cell. Long-term stability was also examined in $CH_4$ and the redox cycle, when the anode is exposed to air. The cell with Pd-doped perovskite anode had high tolerance against re-oxidation and recovered the behavior of anodic performance from catalytic degradation. This recovery of power density can be explained by the surface segregation of Pd nanoparticles, which are self-recovered via re-oxidation and reduction. In addition, self-recovery of the anode by oxidation treatment was confirmed by X-ray diffraction (XRD) and scanning electron microscopy (SEM).

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.6 no.2
• /
• pp.301-312
• /
• 1996

This study was performed to search a optimal analyzing method of cadmium in whole-blood. Cadmium was determined by graphite furnace atomic absorption spectrometry(GFAAS). We investigated the effect of ashing temperature on the absorbance of cadmium in a simple dilution(ten-fold) method with triton X-100 and matrix modifier methods treated with $NH_4H_2PO_4$(1 and 3%) and $Pd(NO_3)_2$(0.00l and 0.005%) as matrix modifier. We also compared the reported reference values of standard blood with values resulted from optimal analyzing conditions of this study. In case of a simple dilution method, when ashing temperature was set at $450^{\circ}C$, the absorbance of sample and background were $0.334{\pm}0.012$ and $1.382{\pm}0.245$, respectively. Background level was higher than the value(0.8) that can be corrected by $D_2$ background correction method. As ashing temperature was rised to $500^{\circ}C$, the absorbance of sample and background were $0.178{\pm}0.008$ and $0.711{\pm}0.223$ respectively. The higher ashing temperature($450^{\circ}C-650^{\circ}C$) was, the lower the absorbance of sample was. In case of a matrix modifier method with $NH_4H_2PO_4$(1 and 3%), when ashing temperature was rised from $500^{\circ}C$ to $650^{\circ}C$, the absorbance of sample slightly changed. The absorbances of sample at $600^{\circ}C$ were $0.230{\pm}0.017$ and $0.137{\pm}0.012$, respectively. These values were larger than that of simple dilution method. But the absorbance of background was higher than the level that can be corrected by $D_2$ method. In case of a matrix modifier method with $Pd(NO_3)_2$(0.001 and 0.005%), the absorbance of sample and background were higher than those of other methods and were stable and reproducible. When ashing temperature was over $550^{\circ}C$, the absorbance of sample was significantly decreased. In case of 0.005% $Pd(NO_3)_2$ carbon residue remained in graphite tube affected the absorbance of sample and background. From these results, We propose that in case of a simple dilution(ten-fold) method with triton X-100 ashing temperature must be maintained below $400^{\circ}C$. In order to diminish the absorbance of background, the alternative method is attenuation of injection volume or multiplication of dilution ratio. We recommend $Pd(NO_3)_2$ than $NH_4H_2PO_4$ as a matrix modifier. In case of a matrix modifier method with $Pd(NO_3)_2$ ashing temperature might be maintained below $550^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.3
• /
• pp.623-626
• /
• 2008

Spin-coating electrostatic self-assembly (SCESA) is utilized to fabricate a single layer of carboxylic-acid-coated Pd nanoparticles (NPs) (D??5 nm) on an oppositely charged surface. The packing density of a NP monolayer formed on a rotating solid substrate (3000 rpm) was examined with regards to various parameters, including the particle concentration, the pH, and the ionic strength of the solution. Initially, the packing density grew exponentially with increases in the particle concentration, up to a maximum value (of 8.4 ´ 1011/cm2) at 1.2 wt%. The packing density was also found to increase drastically as the pH decreased and the ionic strength of the solution increased; these trends can be attributed to a reduction in the interparticle repulsions among the NPs in the solution and on the substrate. The best result of this study was achieved in a 1.2 wt% solution at pH 8; under these conditions, an NP monolayer with the highest density (namely, 1.6 ´ 1012/cm2) was obtained.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.6
• /
• pp.845-851
• /
• 2002

The synthesis of the intramolecular donor - stabilized silyl and germyl complexes of the type ($Cab^c.p) MMe_2X$ (2a:M=Si, X=Cl;2b;M= Ge, X=Cl;2e;M=Si,X=H) was achieved by the reaction of $LiCab^c,p$ (1) with $Me_2SiClX$ and $Me_2GeCl_2$ respectively. The intramolecular M←P interacion in 2a-2c is provided by $^1H$, $13^C.$, $31^P$ and $29^Si$ NMR spectroscopy. The salt elimination reactions of dichlorotetramethyldisilane and -digermane with 1 afforded the $bis(\sigma-carboranylphosphino)disilane$ and disgermane [$(Cab^C.P)MMe_2]_2(4a;M$ = Si;4b: M=Ge). The oxidative addition reaction of 4a-4b with $pd_2(dba)_3CHCl_3afforded$ the bis(silyl)-and bis(germyl)-palladium complexes. The chloro-bridged dipalladium complexes were obtained by the reaction of 2a-2b with $pd_2(dba)_3CHCl_3$ The crystal structures of 5a and 7b were determined by X-ray structural studies.

• KSBB Journal
• /
• v.16 no.1
• /
• pp.76-81
• /
• 2001

Stigmastanol, a functional agent of cholesterol-lowering in humans, was synthesized from stigmasterol. To investigate the usability as a raw material, the contents of sterol in vegetable oils and extract of soybean chaff were analyzed. The total sterol contents showed high values of 213.7 and 209.8 mg/100g in corn and soybean oils respectively. The extract of soybean chaff has played a good role as a raw material with high sterol contents. The kinetics of hydrogenation of stigmasterol was studied using a 5% Pd/AC catalyst in the temperature range of 30~$60^{\circ}$C. Increasing temperature showed a prominent decrease in conversion. The optimum temperature was $40^{\circ}$C for high yield of stigmastanol. The effects of $H_2$ pressure, agitation speed, catalyst loading, and stigmasterol concentration on reaction rate profile were also examined. From the power law model analysis using the initial rates of reaction, the reaction order was calculated as 0.705 for stigmasterol concentration and 0.147 for hydrogen pressure.