• Journal of the Semiconductor & Display Technology
• /
• v.13 no.4
• /
• pp.33-36
• /
• 2014

In this paper, a carbon strain gauge for large strain was developed. The carbon strain gauge was fabricated by forming PCB and antenna pattern using Cu/Ni/Au film and carbon resistor pattern using screen printing process on plastic film substrate. It was possible to develop low-cost disposable strain gauge since the carbon paste was cheap and the fabrication process was simple. The wireless communication type carbon strain gauge was fabricated by integrating signal processing circuit, antenna and power all together on the same substrate as a strain gauge. The wireless communication type carbon strain gauge has a merit of being available immediately at the spot without any particular system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.1
• /
• pp.52-56
• /
• 2006

This paper presents a cross-eye characteristics of multi-path wave scattering. Cross-eye method uses the phase differences of multi signals and is used fur electronic protection. When a signal is propagated from transmitter to receiver on the ground surface, direct wave and reflected wave signals are combined in front of the receiving antenna with different phases. To calculate and control the amplitude and phase of reflected signal, we have developed a cross eye electronic protection method for radar system and studied the variation of electric power density.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1266-1268
• /
• 2004

This is a thesis that a quarter-brick size of 100W class open-frame type on board power module comprising telecommunication application is reported. The input voltage is established between 36 and 75 in range in order for power module to be utilized for the telecommunication application, and output were set at 3.3V and 30A. A number of parts used for transformer, inductor, and hit sink are composed of PCB in order for DC-DC converter to be lowered below 8 mm. A constant current control circuit was annexed to the system as well as basic protection prototypes such as over-voltage, over-current, and over-temperature were well considered to enhance more credibility, and were tested. As a result, high circuit performance and credibility turned out to be significant.

• IE interfaces
• /
• v.23 no.1
• /
• pp.58-67
• /
• 2010

The purpose of this paper is to present the development processes of the assembly line tester of power transmission for lift truck. Because power transmission is most important part of lift truck, all assembled powertrain parts must be inspected for operational defects, pressures and RPM. Developed assembly line tester is designed to take about 25 minutes for inspecting each assembled power transmission and located it at the end of assembled line. The assembly line no-load tester consists of three parts: (1) the driving hardware part; for installing and operating the transmission. (2) control PCB part; send data from sensors to a computer and control driving part, (3) operation software of no-load tester; for an automatic inspection or manual inspection, for database management and printing transcripts.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1506-1508
• /
• 2005

VCO(voltage controlled oscillator) using mobile communication device decides direct characteristics as parts that affect important in stable oscillation and distortion characteristics of system. VCO used 900 MHz band was designed by the transformation of Colpitts circuit form use ADS that consider Q-factor to minimize phase noise. VCO manufactured together evaluation board and voltage control oscillator to FR-4 PCB. VCO experimented chracteristics after control through resonance department tuning. In our research, the designed VCO has 15.5 dBm output level at the bias condition of 6V and 10mA and the operating frequency range of 917 MHz$\sim$937 MHz band. Phase noise is -98.28 dBc/Hz at 1 MHz frequency offset from the carrier.

• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.2
• /
• pp.187-194
• /
• 2017

This study examined the validity and reliability of the thermal safety design, in order to maintain the heat generated from integrated circuit (IC) chips in the converter, condenser, resistor, and transistor (which are considered as heat sources for thermoelectric devices with a printed circuit board) below target levels during the process of developing a control board and a main power board. The study analyzed the heat generation and dissipation characteristics of the entire printed circuit board (PCB) model to examine its thermal safety.

• Journal of Korea Multimedia Society
• /
• v.21 no.12
• /
• pp.1379-1386
• /
• 2018

In this paper, we proposed eyeglass type periorbital wrinkle treatment device for reducing and improving periorbital wrinkles using near infrared LED of 850nm wavelength and galvanic current. The proposed periorbital wrinkle treatment device is equipped with a control system based on F-PCB. It consists of eight near-infrared LEDs and four indicator LEDs for treatment of right and left periorbital wrinkles. The eyeglass frame is coated with conductive material, so galvanic current can flow to the skin of periorbital wrinkle contacted to it. One male adult in the mid-40s was allowed to use the device for 10 minutes every day for 4 weeks. After 4 weeks, image analysis using optical equipment for measuring wrinkles indicated that wrinkle indexes were reduced.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.10
• /
• pp.146-153
• /
• 1996

This paper presents the development of a collocated capacitance sensor and its application to the controller design for magnetic bearing supported rotor systems. The main feature of the sensor is that it is made of a compact printed circuit board(PCB) so that it can be built into the actuator coil of the magnetic bearing unit. The singnal processing unit hax been also developed. The experi- mental results of the sensor performance evaluation on sensitivity, bandwidth and resolution are presented. Then, simulation study shows the advantages of the collocated sensor for magnetic bearings over the nonco- llocated sensor. Finally, the experimental result on the performance of the collocated sensor based contrl- ler for a magnetic bearing rotor system is presented.

• Annual Conference of KIPS
• /
• 2011.11a
• /
• pp.1139-1141
• /
• 2011

기존의 산업용 컨트롤러로 많이 사용되는 프로그래머블 로직 컨트롤러(PLC)를 사용할시 고비용과 큰 부피로 인해 정수기를 소형으로 만들기 어렵다. 따라서 본 가정용 정수기는 소형 MCU 사용과 동시에 정수기에 최적화된 PCB를 제작하여 정수기를 소형화 하였다. 재 프로그램 가능한 MCU 채택으로 추후 시스템이 변경되거나, 프로그램에 보완사항이 필요할 경우 손쉽게 업그레이드가 가능하도록 설계하였다.

• Journal of Advanced Information Technology and Convergence
• /
• v.9 no.2
• /
• pp.99-105
• /
• 2019

In this paper, we describe the procedure of simulation design and measured results of a compact planar antenna for handset applications. The broad bandwidth covering the interested frequency band for mobile handset is achieved by introduction of an open ended L-shaped slot which is newly proposed and corresponds to the monopole slot. In order to minimize the impact on circuit part placement, the proposed antenna is placed on the ground plane edge of PCB with size of 60×65 mm². The measurement result for 10dB impedance bandwidths is 640 MHz (1.7~2.34 GHz), covering the required bandwidths for DCS (Digital Cellular System)-1800 (1710 ~ 1880 MHz) / IMT (International Mobile Telecommunication)-2000 (1885 ~ 2200 MHz) bands. In particular, we would like to emphasize the proposed antenna has an omnidirectional radiation pattern suitable for commercial wireless communication.