• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.3210-3212
• /
• 2000

We designed and manufactured 300MHz NMR RF Transceiver. NMR system is composed of NMR Spectrometer, Superconductive Magnet and Pulse Programmer, GUI. NMR RF Transceiver is composed of transmitter, receiver, frequency synthesizer. T/R switch, main power amp., RF coil. To phase modulation, transmitter is composed of mixer, splitter and combiner et al. To weak signal detection, receiver is composed of pre-amp., filter, mixer et al. Each module is manufactured PCB. And installed NMR system to detect chemical component of specimen. In result, we can get the information of specimen.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.2
• /
• pp.225-230
• /
• 2009

We propose a template matching method for component inspection of SMD assembly system. To discriminate wrong assembled components, the input image of component is matched with its standard image by template matching algorithm. For a fast inspection system, the calculation time of matching algorithm should be reduced. Since the standard images of all components located in a PCB are stored in computer, it is desirable to reduce the memory size of standard image. We apply the discrete wavelet transformation to reduce the image size as well as the calculation time. Only 7% memory of the BMP image is used to discriminate goodness or badness of components assembly. Comparative results are presented to verify the usefulness of the proposed method.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1126-1127
• /
• 2007

This paper presents One Cycle Control type PFC converter for power system Unit of LCD TV. A control technique known as One Cycle Control contends reductions in complexity, cost, design time, and PCB real estate, without a sacrifice in performance. In this paper, design and experiment on 300W One Cycle Control type PFC Converter for Power System Unit of LCD TV.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.5
• /
• pp.513-519
• /
• 2013

Line scan camera has been widely used in the area of inspection of glass, film, fabric, iron, PCB and etc. due to the high resolution and the high speed. We developed the line scan based vision system to inspect tangled and cut-off status of yarn in the manufacturing process. The original image is binarized with a proper threshold, and the gap distances in the yarn are measured in real time, so finally the status of the process is decided by the maximum value of the gap distance. All procedures are executed in real time by realization of multi-processed threads. By implementation of this system, the error of the yarn in manufacturing process can be precedently monitored and the loss of the yarn is decreased efficiently.

• Journal of Astronomy and Space Sciences
• /
• v.23 no.1
• /
• pp.39-54
• /
• 2006

HAUSAT-2 is nano satellite with 25kg mass being developed by Space System Research Lab. in Hnakuk Aviation University. This paper addresses HAUSAT-2 small satellite thermal analyses and its verification at satellite system, electronic box, and PCB levels. Thermal model which is used for system-level and box-level thermal analyses was verified and corrected through thermal vacuum/balance test. The new board-level thermal analysis methodology, modelling high-power dissipating EEE parts directly, was proposed. The proposed methodology has been verified with test results.

• Korean Chemical Engineering Research
• /
• v.46 no.6
• /
• pp.1148-1152
• /
• 2008

Molten carbonate oxidation (MCO) is one of the promising alternative technologies for the treatment of the chlorinated organic compounds because it is capable of trapping chlorine during a destruction of them. In this study, destructions of chlorinated organic compounds ($C_6H_5Cl$, $C_2HCl_3$ and $CCl_4$) and an insulated oil containing PCBs were performed by using the two stage molten carbonate oxidation system. MCO reactor temperature largely affected the destruction of the chlorinated organic compounds. Destruction of the chlorinated organics very efficient in the primary MCO reactor however a significant amount of CO was emitted from the MCO system. This CO emission was gradually decreased by an increase in the primary reactor temperature and oxidizing air feed rate. The HCl emission from the MCO system was below 7 ppm regardless of tested conditions. The chlorine collection efficiencies were in the range of 99.95-99.99%. The destruction of PCBs in the insulated oil was efficient at a temperature above $900^{\circ}C$ and overall destruction efficiency of them was determined as over 99.9999%.

• Journal of Aerospace System Engineering
• /
• v.15 no.5
• /
• pp.81-88
• /
• 2021

In general, a non-explosive nylon wire cutting-based holding and release mechanism has been used to store and deploy deployable solar panels of CubeSat. However, with this method, accessing the solar panel's access port for charging the cube satellite's battery and electrical inspection and testing of the PCB and payloads while the solar panel is in storage is difficult. Additionally, the mechanism must have a reliable release function in an in-orbit environment, and reusability for stow and deploy of the solar panel, which is a hassle for the operator and difficult to maintain a consistent nylon wire fastening process. In this study, we proposed a pin-puller-based solar panel holding and release mechanism that can easily deploy a solar panel without cutting nylon wires by separating constraining pins. The proposed mechanism's release function and performance were verified through a solar panel deployment test and a maximum separation load measurement test. Through this, we also verified the design feasibility and effectiveness of the pin-puller-based separation device.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.4
• /
• pp.57-61
• /
• 2007

We designed and fabricated square coils of 4 layered structure on a PCB board. The size of the coils were $1{\times}1cm^2\;and\;$2{\times}2cm^2$. The line width of the fabricated coils was $100{\mu}m$. By reciprocating a magnet on the surface of a fabricated square coil which is composed of 4 layers, an alternating output voltage was obtained. We changed the vibrational frequency from 0.5 to 7 Hz. The generated voltages were 62 mV at $1{\times}1cm^2$ and 245 mV at $2{\times}2cm^2$ when 5.5 Hz frequency. We rectified and stepped up the output voltage using a quadrupler circuit and $2{\times}2cm^2$ coil. Before using the step up circuit, the measured voltage was 320 mV at 7 Hz. After using the step up circuit, the measured voltage was 400 mV at 7 Hz.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.163-166
• /
• 2005

Multilayer LTCC technology enables RF modules to be reduced dramatically by taking advantage of the three dimension flexibility. Compared to a conventional two dimensional PCB, LTCC allows higher density, reduced size, and lower cost. In this research, BPF based on LTCC for 900MHz ZigBee application was implemented which can replace SAW filter with using the material of the Dupont9599's dielectric constant 7.8. And distributed baud pass filter for 900MHz ZigBee system applications is presented. Using resonator stripline and capacitance, 2nd order band pass filter was designed. Adjusting resonator's length and capacitance is easy to tune at accurate center frequency by shifting band because ZigBee system is using narrow bandwidth, $902MHz^{\sim}928MHz$. Also resonator has no limitation in space, so reducing size is possibile. Designed filter had I.L. 2.8dB at 915MHz and attenuation at 815MHz, 1015MHz was 16dB, 15dB, respectively. Therefore, the sharpe cut-off and good insertion loss for ZigBee system application.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.2 s.95
• /
• pp.39-49
• /
• 1999

This paper describes the development of a vision-aided position and orientation recognition system for automatically adjusting electronic tuners which control the waveform by rotating variable resisters. The position and orientation recognition system estimates the center and the angle of the tuner grooves so that the main controller may correct the difference from the ideal position and thereby manipulate the variable resisters automatically. In this paper a robust algorithm is suggested which estimates the center and the angle of the tuner grooves fast and precisly from the source image with lighting variance and video noise. In the algorithm morphological filtering, 8-chain coding, and invariant moments are sequentially used to figure out image segments concerned. The performance of the proposed system was evaluated using a set of real specimens. The results indicate the system works well enough to be used practically in real manufacturing lines. If the system adopts a high speed frame grabber which enables real time image processing, it can also be applied to positioning of robot manipulators as well as automated PCB adjusters.