• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.10
• /
• pp.820-826
• /
• 2013

In this paper, a compact and wideband CLAS(Conformal Load bearing Antenna Structure) was studied using smart skin technique. In order to satisfy the electrical performance of the CLAS antenna, the proposed CLAS antenna is composed of conductive mesh, face-sheet, radiator, honeycomb, housing. Especially, radiator is composed of composite magneto-dielectric material and radiating element etched on the PCB (Printed Circuit Board). The radiating element is inserted into the composite magneto-dielectric material and has sloted Folded LP(Log Periodic) structure. By fabricated composite magneto-dielectric, the resonance frequency is decreased and the impedance matching characteristics is improved. We verified that the antenna has wideband characteristics and compact size using the antenna test results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.7
• /
• pp.1261-1266
• /
• 2009

In this paper, triple band mobile chip antenna for DCS(1.71${\sim}$1.88GHz) / PCS(1.75${\sim}$1.87GHz) / UPCS(1.8S${\sim}$1.99GHz) on PCB Layout is designed. To analyze the characteristics of the designed antenna, we used commerical simulation tool(HFSS). Triple and wide band characteristic could be realized the measured bandwidth(V.S.W.R<2.0) of the designed antenna operated in 1.71GHz${\sim}$1.99GHz. The size of the designed antenna is about 19mm${\times}$4mm${\times}$1.6mm, narrow bandwidth which is a defect of chip antenna is improved. And its experimental results were a good agreement with simulation performance.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.474-478
• /
• 2019

In this paper, we analyze the degradation of receiving sensitivity due to the coupling between digital noise and mobile handset antenna using characteristic mode. First, we analyze the coupling mechanism between the antenna and digital noise, and analyze the role of the decoupling capacitor of the ground signal line, which is one of the ways to improve the antenna receiving sensitivity degradation due to camera noise. For the analysis, the digital signal line and the ground line of the FPCB of the camera module are modeled as a loop type feeder that excites the characteristic mode of the PCB ground, and improved model which has a ground line with a capacitor are analyzed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.7
• /
• pp.1541-1547
• /
• 2005

In this paper, Dualband internal antenna for GSM/DSC handset is proposed. The antenna has a size of about $38mm{\times}90mm{\times}1mm$, giving a total mobile phone PCB for support and fold type patch of about $30mm{\times}8mm{\times}3.2mm$. This antenna characteriatic facilitates the fine-tuning of the two operating frequencies of 909MHz and 1762MHz in the dualband design. The measured radiation pattern in the E-plane and H-plane for operating frequencies of 909MHz and 1762MHz is compared and analyzed. The designed and fabricated two band internal antenna for GSM/DSC handset have a gain between 0dBi and 2.0dBi at all bands. Also, the electric firld distribution and directivity on human head caused by portable phone is analyzed. An analysis model is composed of a human head model and the antenna mounted on the same ground plane as portable telephone size.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.9
• /
• pp.769-776
• /
• 2015

In this paper, a broadband MIMO antenna using the metal cover that is one of the antenna radiators is designed and implemented on the PCB. The proposed antenna consists of a monopole and an IFA fed by the coupling structure and a metal cover radiator. Therefore, a monopole and an IFA with a metal cover radiator operate simultaneously through a hybrid form of operation. The antenna satisfies VSWR 3:1 at the bands of LTE class 13, class 14, CDMA, GSM900, DCS, PCS, WCDMA, LTE class 40 and WiFi. The maximum ECC of diagonally fed MIMO antenna is 0.186. The measured average gain and efficiency were -5.14~-1.28 dBi and 30.87~74.48 % over the desire bands, respectively.

• Journal of Advanced Navigation Technology
• /
• v.13 no.2
• /
• pp.244-251
• /
• 2009

In this paper, a compact slot antenna for 2.4GHz ISM band applications has been designed. The folded slot with some additional meander sections are used in the design of the antenna within the restricted PCB space. The operating frequency band and the fractional bandwidth of the antenna is about 2.32~2.58 GHz and 11%, and the radiation patterns within the operation bandwidth are almost same. Also, the radiation efficiency and gain of the antenna is more than 49% and 1.2 dBi respectively. To check the validity of the design result, the measurement and simulation results are compared and presented.

• Journal of Advanced Navigation Technology
• /
• v.17 no.2
• /
• pp.171-176
• /
• 2013

A microstrip-fed miniaturized folded-slot antenna that is cut at the finite ground plane edge for the size reduction is proposed as a ZigBee module operating in the 2.4 GHz frequency band, as specified by the IEEE standard 802.15.4. The antenna is fabricated within space limited to $35mm{\times}9mm$ on a $35mm{\times}35mm$ substrate, which is about the PCB size of a typical wireless ZigBee module. The measured impedance bandwidth and antenna gain are 2.37~2.49 GHz and 2.4 dBi respectively. The measured radiation patterns are similar to conventional folded-slot antennas and are also stable across the pass band. These properties and its compact structure help in making the antenna suitable for ZigBee module.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.1
• /
• pp.20-26
• /
• 2013

In this paper, we propose a multi-band monopole antenna with a band-notching U-slot, which is fabricated inside the flexible polymide film substrate. The U-shaped slot located on the patch-shaped monopole antenna provides band-notch at 2.7 GHz, but also helps to improve return loss at adjacent frequency bands. The performance of the antenna attached on an automobile-glass has been simulated and measured. The fabricated antenna provides more than 10 dB return loss for ISM band(2.4~2.483 GHz) and WAVE band(5.85~5.925 GHz), 2.8~5.7 dBi maximum gain, and good radiation patterns.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.83-87
• /
• 2003

본 논문에서는 안테나의 이득을 극대화하기 위해서 Bluetooth PCB Layout 위에 내장형 마이크로 칩 안테나를 직접 설계하여 Bluetooth의 주요 사양인 2.4~2.4835GHz에서 동작할 수 있도록 Bluetooth용 내장형 마이크로 칩 안테나를 설계하였다. Bluetooth PCB Layout 크기는 실제 크기와 같은 54mm$\times$19mm$\times$2.4mm로 설계하고 마이크로 칩 안테나 크기는 11mm$\times$4mm$\times$l.6mm로 설계하여 상용화 된 프로그램인 HFSS에 의해 3.616dBi의 이득을 얻었다. 설계 제작된 Bluetooth용 내장형 마이크로 칩 안테나는 2.45GHz의 중심주파수에서 넓은 대역폭 10.71%을 확인하였다. 또한, 마이크로 칩안테나에서 용량의 변화와 용량의 위치 변화, 급전점의 위치 변화에 따른 공진주파수, 대역폭, 이득 등의 특성을 비교하였고, 제작된 칩안테나의 측정된 방사패턴에서 E-면과 H-면을 비교 분석했다.

• ETRI Journal
• /
• v.46 no.4
• /
• pp.581-594
• /
• 2024

In this study, a planar printed circuit board (PCB) coil with FR4 substrate was designed and simulated using the finite element method, and the results were analyzed in the frequency domain. This coil can be used in wireless power transfer (WPT) as a transmitter or receiver, eliminating wires. It can also be used as the receiver in radio frequency energy-harvesting (RF-EH) systems by optimizing the planar PCB coil to convert radio-wave energy into electricity, and it can be employed as an excitation (transmitter) or receiver coil in nuclear magnetic resonance (NMR) spectroscopy. This PCB coil can replace the conventional coil, yielding a reduced occupied volume, a fine-tuned design, reduced weight, and increased efficiency. Based on the calculated gain, power, and electromagnetic and electric field results, this planar PCB coil can be implemented in WPT, NMR spectroscopy, and RF-EH devices with minor changes. In applications such as NMR spectroscopy, it can be used as a transceiver planar PCB coil. In this design, at frequencies of 915 MHz and 40 MHz with 5 mm between coils, we received powers of 287.3 μW and 480 μW, respectively, which are suitable for an NMR coil or RF-EH system.