• Polymer(Korea)
• /
• v.34 no.3
• /
• pp.237-241
• /
• 2010

Mechanical characteristics and chemical resistance have been investigated for PC/PBT blends. The changes in mechanical performance of PC/PBT blends was monitored during the treatment with both the PC thinner and general-purpose thinner to figure out the chemical resistance. The PC thinner greatly affected the mechanical properties of PC/PBT blends compared with general-purpose thinner. In the case of PC thinner treatment, the mechanical performance was improved with increased PC content at lower PC content ranges, say below 50%. However the mechanical performance was dropped rapidly at higher PC content ranges due to poor chemical resistance of PC. Transparent pure PC specimen became opaque after chemical treatment with PC thinner, and this can be interpreted by solvent-induced crystallization.

• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.399-403
• /
• 2007

Trans-esterification behavior of polycarbonate/poly(butylene terephthalate) (PC/PBT) blends was investigated during the melt mixing process. Rheological and fracture behaviors, and fracture morphology were also investigated as a function of PC/PBT blend ratio. Based on FT-IR and $^1H-NMR$ results, a trans-esterification reaction was confirmed to occur between PC and PBT during the melt mixing process. The melt index(MI) decreased with increased PC content, indicating the higher flow resistance of PC. The storage and loss moduli were increased by increasing the PC loading, and the PC/PBT blends were rheologically incompatible based on the Cole-Cole plot. The tensile property increased linearly with the increased PC content. However, the impact strength increased until 50 wt% of PC loading, notably around $30{\sim}40wt%$, and then was levelled off at 50 wt%. Rough ridges were formed on the impact fracture surfaces above the 40 wt% of PC content, supporting the observed higher impact strength in this range.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.159-165
• /
• 2004

The shrinkages of injection molded parts are different in molding operational conditions and mold design. It also differs from resins. The shrinkages of injection molded parts for PBT (polybutylene terephthalate), PC (polycarbonate),and glass reinforced PBT and PC have been studied for various operational conditions of injection molding. The part shrinkage of crystalline polymer, PBT was higher than that of amorphous polymer, PC by about two times. The part shrinkages of both polymers decreased as glass fiber content increases. Higher Injection temperature and lower injection pressure resulted in a higher shrinkage in both PBT and PC resins. As mold temperature increases the part shrinkage of PC decreased. However, the part shrinkage of PBT increased as mold temperature increases. The part shrinkage of both PBT and PC resins decreased as gate size increases since the pressure delivery is mush easier for a larger gate size. The part shrinkage of flow direction was less than that of the perpendicular direction to the flow for both pure and glass fiber reinforced resins. The part shrinkage at the position close to the gate was less than that of the position far from the gate.

• Transactions of Materials Processing
• /
• v.13 no.6 s.70
• /
• pp.515-521
• /
• 2004

The shrinkages of injection molded parts are different in molding operational conditions and mold design. It also differs from resins. The shrinkages of injection molded parts fur PBT (polybutylene terephthalate), PC (polycarbonate), and glass reinforced PBT and PC have been studied for various operational conditions of injection molding. The part shrinkage of crystalline polymer, PBT was higher than that of amorphous polymer, PC by about two times. The part shrinkages of both polymers decreased as glass fiber content increases. Higher injection temperature and lower injection pressure resulted in a higher shrinkage in both PBT and PC resins. As mold temperature increases the part shrinkage of PC decreased. However, the part shrinkage of PBT increased as mold temperature increases. The part shrinkages of PBT and PC resins decreased as gate size increases since the pressure delivery is mush easier for a larger gate size. The part shrinkage of flow direction was less than that of the perpendicular direction to the flow for both pure and glass fiber reinforced resins. The part shrinkage at the position close to the gate was less than that of the position far from the gate.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.10
• /
• pp.2165-2171
• /
• 2002

Poly-butylene-terephalate(PBT) can be impact-modified by blending with ABS material. The effects of compatibilizers and ABS content on the mechanical properties of PBT/ABS blend were examined in this study. EPDM-g-GMA and polycarbonate(PC) were used as a compatibilizer. As the GMA content in EPDM-g-GMA increased, the tensile strength of PBT/ABS blend increased and the impact strength decreased. With increasing the EPDM-g-GMA content in PBT/ABS blend, the tensile strength and impact strength decreased. With PC compatibilizer, the particle size of ABS in PBT/ABS blend became smaller than that of the blend without compatibilizer and the particles were more evenly dispersed in matrix. The maximum impact strength of the PBT/ABS blend was observed in the range of 20~30% ABS content.

• Polymer(Korea)
• /
• v.26 no.2
• /
• pp.237-244
• /
• 2002

Mechanical properties, flow characteristics and chemical resistance of polycarbonate (PC)/polybutylene terephthalate (PBT) /impact modifier (IM) blends were investigated over the various composition ranges of PC and PBT. Mechanical properties of the PC/PBT/IM blends for different IMs, butadiene based IM and butyl acrylate based IM, were studied for various compositions of the IMs. Impact strength at low temperature was also observed. For the study of chemical resistance of the PC/PBT/IM blends, the blonds were dipped in organic solvent, thinner, and then variations of mechanical properties were analyzed. Tensile and flexural strengths were increased linearly and heat distortion temperature (HDT) also increased as PC content in the blends increased. Impact strength increased drastically as PC content increased up to 50 wt% and stayed stable value. Flowability decreased as PC content increased. Impact strengths of the blend were various for different IMs. Butyl acrylate based IM showed slightly higher impact strength than butadiene based IM for the temperature above $0^{\circ}C$. However, butadiene based IM showed remarkably higher impact strength than butyl acrylate based IM for the temperature below $0^{\circ}C$. Through the experiment of chemical resistance it was observed that tensile and flexural strengths decreased, and impact strength increased as PC content in the blends increased. PC in the blend would become mild and ductile when it contacted with organic solvent. Thus the impact strength increased while tensile and flexural strength decreased.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.10a
• /
• pp.149-152
• /
• 2001

Poly-butylene-terephalate(PBT) can be impact modified by blending with ABS material. The effects of the type of compatibilizer and ABS content on the mechanical properties of PBT/ABS blend were examined in this study. EVA-g-GMA and three type of polycarbonates were used as the compatibilizer. As the GMA content in EVA-g-GMA was increased, the tensile strength of PBT/ABS blend increased and the impact strength of it decreased. With increasing the EVA-g-GMA content in PBT/ABS blend, the tensile strength and impact strength decreased. With PC compatibilizer, the tensile strength of PBT/ABS blend decreased as the ABS content increased. However, the maximum impact strength was observed in 20~30% ABS content range.

• Macromolecular Research
• /
• v.16 no.7
• /
• pp.620-625
• /
• 2008

A novel nitrogen-phosphorus compound, diphenyl piperazine-1,4-diylbis(methylphosphinate)(DPPMP) was synthesized via a two step reaction and its flame retarding efficiency as a single component additive was investigated. The success of synthesis was confirmed by FTIR and $^1H$ and $^{31}P$ NMR analysis. The product was mixed with polycarbonate (PC), poly(butylene terephtalate) (PBT), ethylene-vinyl-acetate copolymer (EVA), and acrylonitrile-butadiene-styrene copolymer (ABS). The flame-retarding efficiency was evaluated using the limiting oxygen index (LOI) and the UL-94 vertical test methods. The addition of DPPMP enhanced the flame retardancy of the polymers and the V-0 ratings were obtained for the polymers examined in this study at a loading of 7-30 wt%. The gas-phase flame retardancy mode of action was suggested for this material from the thermogrametry experiment results.

• Journal of the Korean Magnetic Resonance Society
• /
• v.5 no.1
• /
• pp.19-28
• /
• 2001

Miscibility and morphology in blends of bisphenol-A type polycarbonate and poly (ester-ether) elastomer with different compositions are studied by solid-state NMR spectroscopy. $^{13}$ C Solid-state NMR of CP/MAS/TOSS/DD, CP/MAS/DD, inversion recovery CP/MAS/DD, and 2D rotor driven spin diffusion techniques are used to identify the miscibility, morphology, and transesterification in blends. The blends of PC /BT elastomer with 15% to 42% of soft segment seem to be single phase miscible mixing and those of PC/PBT and PC/PBT elastomer with 62% of soft segment are cocontinuous two phase immiscible mixing. No significant transesterification reactions are observed in blends with different compositions.

• Elastomers and Composites
• /
• v.47 no.4
• /
• pp.336-340
• /
• 2012

Residual stress in the injection molded part is originated from thermal shrinkage and shear stress during injection molding process. There are many measurement methods of residual stress in the plastic part. Residual stress in opaque products can be measured by chemical cracking test. This method enables the solvent and specimen to react and to cause cracks. Cracks developed according to the level of residual stress. Thus the stresses in plastic part can be quantitatively measured by counting the number of cracks or measuring the size of cracks. Relationship between stress and number of cracks in a plastic specimen has been investigated in this study. Bergen jig was used to give a strain in the specimens those were molded using PC/PBT and PC/ABS. Solvent for the chemical cracking test was prepared using tetrahydrofuran and methyl alcol with the ratio of 1 to 3. Stresses in the specimen can be calculated by strains those were imposed by Bergen jig. Cracks were developed for stress higher than certain level. The number of cracks increased by second order function for stress.