• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.5
• /
• pp.733-737
• /
• 2012

The objectives of this study were to investigate soil chemical properties for forest rehabilitation and suggest design and management in abandoned coal mine areas in Mungyeong, Gyeongsangbuk-do. Total study sites were 10 sites, and soil analysis particular were soil pH, TOC, total-N, C/N ratio, A.v. $P_2O_5$, and CEC. Because most of study sites showed soil pH from 5.0 to 7.0, it seems that soil pH does not affect growth of vegetation. But soil pH in Danbong1 was acidic (pH 4.6), so it is needed to improve with ameliorant such as limestone. Most of study sites is necessary to manage for organic matter and Nitrogen, because there sites showed lower value of TOC and total-N than general forest. The values of A.v. $P_2O_5$ and CEC were good in most of study sites, so it seems that they do not have effect on vegetation growth. All of soil factors has no regression according to elapsed time after rehabilitation. TOC, total-N and A.v. $P_2O_5$ among soil properties have positive relationship between each other. It is necessary to fertilizer for organic matter and Nitroge because of value in TOC, total-N and C/N ratio. The results of this study were analyzed only one time. So, long-term monitoring for soil properties is important for the correct forest rehabilitation and management.

• Economic and Environmental Geology
• /
• v.38 no.5 s.174
• /
• pp.579-585
• /
• 2005

Cheap and environmental sound biosorbent was made for the adsorption of arsenate using an waste activated sludge. The biosorbents were methylated in 9hours and 24 hours respectively for the better adsorption of arsenate. The amount adsorbed of arsenate(V) increased with increasing methylation time. The specific arsenate adsorption was 0.06mmol As(V)/g biomass when the biosorbent was methylated in 24 hours. The methylated biosorbents were also studied with pH 5, 7 and 9. The pH of the solution affect the amount of adsorption of arsenate of the biosorbent even though it was methylated. The specific arsenate adsorption of the biosorbent at pH 5 was best and it was three times greater than the amount of arsenate adsorbed at pH 9.

• Journal of the Korean Society for Precision Engineering
• /
• v.3 no.2
• /
• pp.62-75
• /
• 1986

An experimental investigation of the machining characteristics such as cutt- ing resistance, surface roughness and tool wear in turning the test pieces of SM45C steel with both coated and uncoated carbide tool tips under various cutting conditions was conducted. Also a specially designed simple vibration damping device was experimentally evaluated for its effectiveness on machined surface roughness and a vibration test was conducted to confirm its ability to reduce the amplitude. Based on these tests finding, the following conclusions are made; 1. The cutting resistance($\textrm{p}_{1}$) increases as the depth of cut(d) increases at fixed feed rate(f) over the cutting speed(v) range of 43-226 m/min and p decreses about 18% average when V is increased for fixed d and f. At V= 226m/min, $\textrm{p}_{1}$/for A, C tips are about the same level but $\textrm{p}_{1}$ for B tip is 15% less than A, C tips. 2. The specific cutting resistance(Ks) at V=226 m/min was derived for A, B, C tips respectively and the value of Ks for B rip is about 20% less than A, C tips. 3. The surface roughness(Ra) improves significantly as the cutting speed(V) is increased and this effect was greater when V>100 m/min. On the other hand, Ra deteriorates as the feed rate(f) is increased and this trend was accelerated when f>0.3 mm/rev. With regard to the difference of Ra values among A, B, C tips, at V=226m/min, d=0.4mm, and f=0.31-0.61mm/rev, Ra values for B.C tips are about 17% less than tip A. 4. The experimental tool wear equations were derived for A, B, C tips and from these equations, the tool life($\textrm{T}_{\textrm{L}}$) baced on the I.S.O. criteria was calculated to be $\textrm{T}_{\textrm{L}}$<$\textrm{T}_{\textrm{LB}}$<$\textrm{T}_{\textrm{LC}}$ for both flank wear($\textrm{V}_{\textrm{B}}$) and boundary wear($\textrm{V}_{\textrm{N}}$). Hence, the coated tips are superior to the uncoated tip and tip C is considered to be the best. 5. The cutting resistance may be slightly reduced and the surface rounghness improved when the damper is used especially when V>100 m/min. Therefore this damping device is considered to be effective and practical. The experimental surface roughness equations were also derived. Based on the vibration test, it is established that the surface roughness improvement was the result of amplitude reduction made possible by the damper.

• Journal of Radiation Protection and Research
• /
• v.24 no.4
• /
• pp.195-203
• /
• 1999

It is difficult to determine dosimetric characteristics for small field photon beams since such small fields do not achieve complete lateral electronic equilibrium and have steep dose gradients. Dosimetric characteristics of small field 4, 6, and 10 MeV photon beams have been measured in water with a diamond detector and compared to measurements using small volume cylindrical and plane parallel ionization chambers. Percent depth dose (PDD) and beam profiles for 6 and 10 MeV photon beams were measured with diamond detector and cylindrical ion chamber for small fields ranging from $1{\times}1\;to\;4{\times}4cm^2$. Total scatter factors($S_{c,p}$) for 4, 6, and 10 MeV photon beams were measured with diamond detector, cylindrical and plane parallel ion chambers for small fields ranging from $1{\times}1\;to\;4{\times}4cm^2$. The $S_{c,p}$ factors obtained with three detectors for 4, 6, and 10 MeV photon beams agreed well ($\pm1.2%$) for field sizes greater than $2{\times}2,\;2.5{\times}2.5,\;and\;3{\times}3\;cm^2$, respectively. For smaller field sizes, the cylindrical and plane parallel ionization chambers measure a smaller $S_{c,p}$ factor, as a result of the steep dose gradients across their sensitive volumes. The PDD values obtained with diamond detector and cylindrical ionization chamber for 6 and 10MeV photon beams agreed well ($\pm1.5%$) for field sizes greater than $4{\times}4\;cm^2$. For smaller field sizes, diamond detector produced a depth-dose curve which had a significantly shallower falloff than that obtained from the measurements of relative depth-dose with a cylindrical ionization chamber. For the measurements of beam profiles, a distortion in terms of broadened penumbra was observed with a cylindrical ionization chamber since diamond detector exhibited higher spatial resolution. The diamond detector with small sensitive volume, near water equivalent, and high spatial resolution is suitable detector compared to ionization chambers for the measurements of small field photon beams.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.4
• /
• pp.194-197
• /
• 2015

La_9.33(Si₅V₁)O₂₆ ceramics were fabricated by the mixed oxide method for solid oxide electrolytes. La_9.33(Si₅V₁)O₂₆ specimens showed the hexagonal, space group P63 or P63/m, and the unit cell volume increased when the sintering temperature increased. The specimen sintered at 1,400℃ showed the X-ray patterns of the homogeneous apatite single phase without the second phase, such as La₂SiO₅ and SiO₂. The specimen sintered at 1,400℃ showed the maximum sintered density of 4.93 g/cm³. When the sintering temperature increased, the electrical conductivities increased, the activation energy decreased and the values were 7.83×10⁻⁴ S/cm, 1.61 eV at 600℃, respectively.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.3
• /
• pp.47-51
• /
• 2013

Current research trends of solar cells has focused on the high conversion efficiency and low-cost production technology. Passivation technology that can be easily adapted to mass production. Therefore, this study conducted experiments with aim of the following two methods for the fabrication of high-efficiency crystalline silicon solar cells. In the first task, an attempt is formation of local Al-BSF to a number of locally doped dots to increase the conversion efficiency of solar cells to reduce the loss of $V_{oc}$ overcome. The second major task, rear surface apply in $Al_2O_3/SiN_x$ stack layer, $Al_2O_3$ prominent negative fixed charge characteristics. As the result of task, Local Al-BSF and $Al_2O_3/SiN_x$ stack layer applied to the p-type single crystalline silicon solar cells, the average $V_{oc}$ of 644mV, $I_{sc}$ of 918mV and conversion efficiency of 18.70% were obtained.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1660-1663
• /
• 1999

혈액 내의 요소 농도는 신장병 진단의 척도로서 정확한 측정이 필요하다. 요소의 농도는 전위차법을 이용하여 정확히 검출할 수 있으며 이를 위하여 효소를 고정화시킨 전극형 센서를 사용하였다. 전도성 고분자로서 P3MT(Poly(3-methylthiophene) )와 PPy(polypyrrole)를 효소 고정화에 이용하였다. PPy는 전기적 특성이 좋고 중합 및 효소의 고정화가 용이하며 중합 과정이 상대적으로 신속하고 비용도 저렴하다는 장점은 있으나. 다소 불안정하다. P3MT는 PPy와 마찬가지로 전극 상에 단량체가 전기적 산화에 의하여 중합되고 일반적으로 전해질 이온이 도우핑된 상태나 도우핑 되지 않은 상태 모두에서 산소. 습도. 온도에 대하여 매우 안정하다. 본 연구에서는 3-methylthiophene과 pyrrole을 전기 중합하여 urease를 고정화한 요소센서의 특성(감도, 안정성, 직선성)을 비교하였다. P3MT를 이용한 센서와 PPy를 이용한 센서 각각에 대해 감도는 P3MT가 32.3mV/decade, PPy가 4.7mV/decate로서 P3MT가 우수하였고 직선성도 보다 뛰어났으며 순환 전압 전류 곡선을 분석한 결과 P3MT가 PPy보다 안정성도 우수한 특성을 보였다.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.52 no.5
• /
• pp.47-52
• /
• 2010

The purpose of this study is to investigate characteristics of total phosphorus (TP) and phosphate phosphorous ($PO_4$-P) concentrations in ponded water and redox potential (Eh) in paddy soil during the growing season. The TP and $PO_4$-P concentrations showed twice peak values after basal dressing and tillering fertilization. The ratio of $PO_4$-P to TP showed low values (0.07~0.18), indicating that most of phosphorus is particlulate. The $PO_4$-P concentrations significantly decreased with dissolved oxygen (DO) concentrations. The Eh showed high values (179~636 mV) under non-ponded aerobic condition, but low values (74~112 mV) under ponded anaerobic condition The TP and $PO_4$-P concentrations in ponded water increased shortly after tillering fertilization even if phosphorus was not applied. This may be due to the release of dissolved phosphorus from the bottom sediment and its associated algal and water flea blooms under anaerobic condition. Therefore, proper water management should be needed shortly after tillering fertilization.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.7
• /
• pp.185-197
• /
• 1996

We have adopted the strain compensated PBH(planar buried heterostructure) - LD in which the MQW active layer consisted of 1.4% compressively strained GainAsP (E$_{g}$ = 0.905eV) wells and 0.7% tensile strained GaInAsP(E$_{g}$ = 1.107eV) barriers grown by metal organic vapor phase epitaxy (MOVPE). We hav einvestigated effects of number of wells and the structure of the separate confinement heterostructure (SCH) layer in the strain-compensated MQW-PBH-LD. The threshold current, the external quantum efficiency, the transparency current density J$_{o}$, and the gain constant .beta. have been evaluated for uncoated MQW-PBH-LD. As the number of wells increases, the internal quantum efficiency and the transparency current density decreases, whereas the gain contant increases. The small width of the SCH layer shows the large internal quantum efficiency. The small internal loss and the large gain constant have been obtained by inserting the large bandgap SCH layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.308-311
• /
• 2000

The organic electroluminescene (EL) device has gathered much interested because of its potential in materials and simple device fabrication. We fabricated EL device which have a mixed single emitting layer containing N,N'-diphenyl-N,N'-(3-methylphenyl)-1,1'-biphenyl-4,4'-diamine [TPD] and poly(3-hexylthiophene) [P3HT]. The molar ratio between P3HT and TPD chaged with 1:1, 3:1, 5:1, 3:2 and 5:2. EL intensity of ITO/P3HT+TPD/Mg:In devices is enhanced by addition of TPD into P3HT. This can be explained that the energy transfer occurs from TPD to P3HT. Recombination probability increases in emitting layer because that TPD as hole transport material plays a role more injection hole and Mg:In (3.7eV) electrode has low work function make easily electron injection. ITO/P3HT+TPD(5:2)/Mg:In devices emit orange-red light at 28V.