• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.7
• /
• pp.56-61
• /
• 1997

I $n_{0.53}$G $a_{0.47}$As/I $n_{0.52}$A $l_{0.48}$As pseudomorphic high electron mobility transistor (P-HEMT) structures were grown on semi-insulating InP substrates by molecular beam epitzxy method. The hall effect measuremetn was used to measure the electrical properties and the photoluminescence (PL) measurement was used to measure the electrical properties and the photoluminescence(PL) measurement for optical propety. By the cross-sectional transmission electron microscopy (XTEM) investigation of the V and X shape defects including slip with angle of 60.deg. C and 120.deg. C to surface in the sampel, the defects formation mecahnism in the I $n_{0.52}$A $l_{0.48}$As epilayers on InP substrates could be explained with the different thermal expansion coefficients between I $n_{0.52}$A $l_{0.48}$As epilayers and InP substrate.d InP substrate.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10A
• /
• pp.965-970
• /
• 2005

In this paper, SPDT Tx/Rx MMIC switch applicable to IEEE 802.11a WLAN systems is designed and fabricated using a specific designed epitaxial layered pHEMT wafer and ETRI's $0.5{\mu}m$ pHEMT switch process. The SPDT switch exhibits a low insertion loss of 0.68dB, high isolation of 35.64dB, return loss of 13.4dB, power transfer capability of 25dBm, and 3rd order intercept point of 42dBm at frequency of 5.8GHz and control voltage of 0/-3V. The comparison of the measured performances with commercial products based on the GaAs pHEMT technology for low voltage operating at ${\pm}$ 3V/0V shows that the return loss is somewhat inferior to the commercial products and insertion loss is compatible with each other however, isolation characteristics are much better than in conventional chips. Based on these performances, we can conclude that the developed SPDT switch MMIC has an enough potential for IEEE802.11a standard 5 GHz-band wireless LAN applications.

• Journal of IKEEE
• /
• v.11 no.4
• /
• pp.152-157
• /
• 2007

AlGaN/GaN high electron mobility transistors (HEMTs) were fabricated and the effect of ${N_2}O$ plasma on the electrical characteristics of the devices was investigated. The HEMT exposed to ${N_2}O$ plasma formed by 40 W of RF power in a chamber with pressure of 20 mTorr at a temperature of $200^{\circ}C$, exhibited a reduction of gate leakage current from 246 nA to 1.2 pA by 10 seconds treatment. The current between the two isolated active regions reduced from 3 uA to 7 nA and the sheet resistance of the active layer was lowered also. The variations of electrical characteristics for HEMT were occurred within a short time expose of 10 seconds and the successive expose did not influence on the improvements of gate leakage characteristics and conductivity of the active region. The reduced leakage current level was not varied by successive $SiO_2$ deposition and its removal. The transconductnace and drain current of AlGaN/GaN HEMTs were increased also by the expose to the ${N_2}O$ plasma.

• Journal of IKEEE
• /
• v.26 no.1
• /
• pp.77-82
• /
• 2022

The effect of the bias network on the performance of the W-band power amplifier(PA) was investigated. The performances of the typical RC and radial stub networks were examined, and a hybrid network was proposed for W-band application and its performance was confirmed. To verify this, a W-band PA was designed using a 60-nm GaN pHEMT process. When hybrid networks were applied, the PA had improved stability in all frequency bands, secured about 9 dB of power gain at operating frequencies 87 GHz to 93 GHz, and the maximum PAE was found to be about 12.3% at output power of 26.7 dBm.

• Journal of the Institute of Convergence Signal Processing
• /
• v.12 no.3
• /
• pp.217-221
• /
• 2011

GaAs-based and InP-based HEMTs(High Electron Mobility Transistors) have good microwave and millimeter-wave frequency performance with lower minimum noise figure. GaAs-based MHEMTs(Metamorphic HEMTs) have some advantages, especially for cost, compared with InP-based ones. In this paper, the RF small-signal circuits of MHEMTs are simulated and analyzed for the design of millimeter-wave application systems. The simulation analysis for RF small-signal frequency can help and give some insights about the MHEMTs for the design of millimeter-wave application and communication systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.3
• /
• pp.171-183
• /
• 2018

Herein, we show the design and fabrication of a serial-to-parallel converter (SPC) using the $0.25-{\mu}m$ GaAs pHEMT process. The serial-to-parallel converter is composed of four bits to control the four phase shifters used in the core chip. The SPC stores the received serial data signal to a register in the SPC and converts the stored data into the parallel data. Each converted output data can control four phase shifters. The size of the fabricated SPC is $1,200{\times}480{\mu}m^2$ and it uses two DC power supplies of 5 V and -3 V. The consumption current of each DC power supply is 7.1 mA for 5 V, and 2.1 mA for -3 V.

• Journal of the Korean Vacuum Society
• /
• v.20 no.5
• /
• pp.345-355
• /
• 2011

GaAs-based metamorphic high electron mobility transistors (MHEMTs) and InP-based high electron mobility transistors (HEMTs) have good microwave and millimeter-wave frequency performance with lower minimum noise figure. MHEMTs have some advantages, especially for cost, compared with InP-based ones. In this paper, InAlAs/InxGa1-xAs/GaAs MHEMTs are simulated for DC/RF small-signal analysis. The hydrodynamic simulation parameters are calibrated to a fabricated 0.1-${\mu}m$ ${\Gamma}$-gate MHEMT device having the modulation-doped $In_{0.52}Al_{0.48}As/In_{0.53}Ga_{0.47}As$ heterostructure on the GaAs substrate, and the simulations for RF small-signal characteristics are performed, compared with the measured data, and analyzed for the devices. In addition, the simulations for the DC/RF characteristics of the MHEMTs with different gate-recess structures are performed, compared and analyzed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.506-514
• /
• 1998

The design and fabrication of X-band(11.7~12 GHz) 2-stage monolithic microwave integrated circuit(MMIC) low noise amplifier (LNA) for active antenna are presented using $0.15{\mu}m\times140{\mu}m$ AlGaAs/InGaAs/GaAs pseudomorphic high electron mobility transistor (P-HEMT). In each stage of the LNA, a series feedback by using a source inductor is used for both input matching and good stability. The measurement results are achieved as an input return loss under -17 dB, an output return loss under -15dB, a noise figure of 1.3dB, and a gain of 17 dB at X-band. This results almost concur with a design results except noise figure(NF). The chip size of the MMIC LNA is $1.43\times1.27$.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.6
• /
• pp.127-132
• /
• 2018

In this paper, a high conversion gain cascode mixer was designed in W-band and verified by the fabrication and measurements. In the high frequency band such as a W-band, the conversion loss of a mixer is increased because of the poor performance of transistors. This high conversion loss of the mixer requires additional circuits which can give an extra gain such as an RF buffer amplifier, and this can affects the linearity and stability of the overall systems. Therefore, it is necessary to maximize the conversion gain of the mixer. To maximize the conversion gain of the mixer, biases of the transistor were optimized, and output load impedance was optimized by the load-pull simulations. The designed mixer was fabricated in $0.1-{\mu}m$ GaAs pHEMT technology and verified by the measurements. The measurement results shows a maximum conversion gain of -4.7 dB at W-band and an input 1-dB compression point of 2.5 dBm.

• Journal of IKEEE
• /
• v.28 no.3
• /
• pp.445-450
• /
• 2024

This paper presents a varactor-less voltage-controlled oscillator (VCO) at W-band (75-110 GHz) with a compact size in a 0.15-㎛ GaAs pHEMT technology. For varactor-less frequency tuning, an inductive tuning circuit is employed. An active inductor is realized by the common-gate stage with gate termination and shows a wide tuning range with a high quality factor (Q-factor) compared with the conventional varactor diode. Colpitts topology with source feedback is employed for the oscillation core of the VCO. The varactor-less VCO exhibits a measured tuning range of 5.8 % and peak output power of 5.7 dBm at 88 GHz while the 146 mW of dc power is dissipated. Due to compact layout design, the chip size is only 0.48 mm².