• Journal of environmental and Sanitary engineering
• /
• v.16 no.1
• /
• pp.34-39
• /
• 2001

Submerged Membrane Bio-Reacter(SMBR) process was used to food wastewater treatment. From laboratory pilot-scale experiment data, it was confirmed that this process was very effective process for organics, suspended solid, and N, P treatment. It was found that BOD and COD removal rate were obtained 90% and 92%, respectively, for 150 days operation. Organics loading rate did not affect to the removal efficiency because MLSS concentration in aerobic tank was highly maintained. IN the case of first reactor operated with anoxic and second reactor operated as aerobic, T-N, T-P removal rate were obtained 93% and 95%, respectively. It was shown that removal efficiency could be maintained stable due to the complete removal of SS and sludge production decreased with increasing of sludge retention time.

• Journal of Environmental Science International
• /
• v.21 no.11
• /
• pp.1371-1377
• /
• 2012

The simulated dyes solution containing Basic Red 46(BR 46), Yellow 21(Y 21), and Maxilon Blue 30(MB 30) were electrochemically oxidized using carbon fiber as an anode. The electrolyses were performed in a electrolytic flow cell constructed by Vycor glass tube. The carbon fiber was positioned in the inside of Vycor glass tube and platinum wire coiled around outside of tube as a cathode. Several operating variables, such as current, time, pH and flow rate of solution were studied. Increasing current density would lead to a corresponding increase in the dye removal efficiency 99.2 % at a 200 mA. The electrolyses time could also improve and removal efficiency was about 99 % after 1.5 hours of electrolyses. The removal efficiency was increased with the increase of flow rate of solution and optimum flow rate was 5 mL/min. THe pHs of solution affect the removal efficiency. The removal efficiency was decreased with the increase of pH of solution and optimum pH was 5.05 (0.1 M $KNO_3$).

• Journal of Korean Society on Water Environment
• /
• v.27 no.2
• /
• pp.235-241
• /
• 2011

This study was performed to investigate the characteristics of nutrient removal of municipal wastewater in the submerged membrane bioreactor by addition of alum directly into aerobic tank. Membrane bioreactor consists of three reactors such as two intermittent anaerobic tanks and the aerobic tank with hollow fiber membrane. The removal efficiencies of $COD_{cr}$, BOD, SS, TN and TP on the membrane bioreactor were 94.0%, 99.1%, 99.9%, 66.9%, and 58.9%, respectively. In addition, The removal efficiencies of $COD_{cr}$, BOD, SS, TN and TP on the membrane bioreactor with alum addition were 93.4%, 99.0%, 99.9%, 63.2%, and 96.8%, respectively. There was little difference between them on the nutrient removal efficiencies except phophorus removal. The estimated sludge production, specific denitrification rate, specific nitrification rate and phosphorus removal content on the membrane bioreactor were 1.76 kgTSS/d, $0.055mgNO_3-N/mgVSS{\cdot}d$, $0.031mgNH_4-N/mgVSS{\cdot}d$, and 0.095 kgP/d, respectively. And The estimated sludge production, specific denitrification rate, specific nitrification rate and phosphorus removal content on the membrane bioreactor with alum addition were 2.90 kgTSS/d, $0.049mgNO_3-N/mgVSS{\cdot}d$, $0.030mgNH_4-N/mgVSS{\cdot}d$, and 0.160 kgP/d, respectively. The alum content added was 1.7 molAl/molP on an average. The increasing ratio of tran-membrane pressure on the membrane bioreactor was $0.0056kgf/cm^2{\cdot}compared$ to $0.0033kgf/cm^2{\cdot}d$ on the membrane bioreactor with alum addition. There was a slightly reduction effect on membrane fouling by alum addition.

• Journal of Korean society of Dental Hygiene
• /
• v.23 no.1
• /
• pp.33-42
• /
• 2023

Objectives: Based on the strengths of augmented reality (AR), this study aimed to determine the dental plaque removal efficiency of a guided brushing program in children. Methods: This randomized, controlled, double-blind crossover clinical trial evaluated the plaque removal rate after regular brushing versus AR-based guided toothbrushing in 20 children aged 5-12 years. Results: Overall, the dental plaque removal efficiency of AR-based brushing was superior to that of regular brushing (p<0.05). When classified in detail, no significant difference was noted in the plaque removal rate between the two brushing methods in the anterior region (p=0.056), whereas a significant difference in the plaque removal rate was observed in the posterior region (p<0.05). Conclusions: Based on these results, the efficacy of dental plaque removal for brushing using an AR-based smartphone application was confirmed; thus, this can be used for oral health education incorporating ICT technology in the future.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.2
• /
• pp.261-268
• /
• 2022

In this study, electrochemical treatment of urban wastewater with electrical conductivity of 1000 μS cm^-1 and chemical oxygen demand of 250 mg L^-1 was investigated using the variables of initial pH value, current density and flow rate. Electrocoagulation was used, in which aluminum and stainless steel were selected, as the electrochemical treatment process. The electrocoagulation process was operated in continuous mode. The data obtained in experimental studies show that the best COD removal efficiency occurred in experiments where the initial pH value was 6. The increase in current density from 5 A to 15 A decreased the removal efficiency from 79 to 67%. The increase in flow rate under constant current density also reduced the efficiency of removal as expected. In experiments in which current density and flow rate were examined together, the increase in flow rate allowed the application of higher current densities. This situation led to considerable reductions in energy consumption values, even if the COD removal efficiency did not significantly increase. The high COD removal obtained with the use of high flow rate and high current density indicates that the electrocoagulation process can be used for high flow rate municipal wastewater treatment.

• Journal of Korean Society on Water Environment
• /
• v.25 no.6
• /
• pp.979-983
• /
• 2009

The mean pH of wastewater discharged from the plating process is 2, so a less amount of alkali is required to raise pH 2 to 5. In addition, if sodium sulfite is used to raise pH 5 to 9 in the secondary treatment, caustic soda or slaked lime is not necessary or only a small amount is necessary because sodium sulfite is alkali. Thus, it is considered desirable to use only $FeSO_4{\cdot}7H_2O$ in the primary treatment. At that time, the free cyanide removal rate was highest as around 99.3%, and among heavy metals, Ni showed the highest removal rate as around 92%, but zinc and chrome showed a low removal rate. In addition, the optimal amount of $FeSO_4{\cdot}7H_2O$ was 0.3g/L, at which the cyanide removal rate was highest. Besides, the free cyanide removal rate was highest when pH value was 5. Of cyanide removed in the primary treatment, the largest part was removed through the precipitation of ferric ferrocyanide: $[Fe_4(Fe(CN)_6]_3$, and the rest was precipitated and removed through the production of $Cu_2[Fe(CN)_6]$, $Ni_2[Fe(CN)_6]$, CuCN, etc. Furthermore, it appeared more effective in removing residual cyanide in wastewater to mix $Na_2SO_3$ and $Na_2S_2O_5$ at an optimal ratio and put the mixture than to put them separately, and the optimal weight ratio of $Na_2SO_3$ to $Na_2S_2O_5$ was 1:2, at which the oxidative decomposition of residual cyanide was the most active. However, further research is required on the simultaneous removal of heavy metals such as chrome and zinc.

• Journal of Animal Science and Technology
• /
• v.45 no.4
• /
• pp.641-648
• /
• 2003

In a batch mode treatment process, which electrolyzes the wastewater after derivation of N-P crystal formation and recovery, the characteristics of pollutant removal induced with the changes of loading rate and hydraulic retention time were studied. $MgCl_2$ was used as Mg source for the formation of struvite and the molar ratio of $MgCl_2$ to $PO_4^{3-}$ in influent was 1.3. When analyzing the average treatment efficiencies and removal characteristics obtained from four separate operations (Run I, II, III, IV), removal efficiencies of PO43- was not function of its loading rate. Under a condition of sufficient aeration and Mg source provided, over 88% of $PO_4^{3-}$ was eliminated by the formation of MAP without any pH adjustment, in spite of loading rate variation. An optimum-loading rate of NH4-N to achieve high removal efficiency was approximately $100g/m^3/d$. Below that loading rate, the removal of NH4-N was proportional to the loading rate into the system, and hence stable and high removal efficiency, over 90%, was achieved. However, when the loading rate increased over that rate, removal efficiency began to drop and fluctuate. Removal efficiency of TOCs was dependant upon the hydraulic retention time ($r^2$=0.97), not upon the loading rate. Stable and high color removal (94%) was obtained with 2 days of HRT in electrolysis reactor.

• Journal of Environmental Science International
• /
• v.13 no.3
• /
• pp.289-295
• /
• 2004

The objective of this study is to delineate removal efficiency of the MTBE in solution by $TiO_2$ photocatalytic degradation as a function of the following different experimental conditions: Initial concentration of MTBE, air flow rate in solution, $H_2O_2$ dosage and pH of the solution. Photodegradation rate was increased with decreasing initial concentration of MTBE. The removal efficiency was 82% after 180 min in the case of MTBE concentration of 100 mg/L but 100% after 180 min in the case of 20 mg/L. Removal efficiency was increased with increasing pH, $H_2O_2$ dosage and air flow rate in solution.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.14 no.2
• /
• pp.105-109
• /
• 2008

In our country, limiting nutrient is known as phosphorus in the most lakes. Therefore, the removal of phosphorus is a very important process in sewage treatment. However, many of the sewage treatment plants employ the conventional activated sludge process, known to remove $10{\sim}30%$ of phosphorus. Thus, additional phosphorous removal process will be needed. Oyster shells have been known to remove phosphorus in water. The removal efficiency of phosphorus was highest at smallest size of oyster shells and at the highest pH for batch test. The phosphorous removal rate with various calcium concentrations was increased by increasing calcium concentration. At the 20 mg/l of calcium, more than 90% of phosphorous was removed in two hours. The removal efficiency of phosphorous was increased greatly at 300% of recirculation rate. With 300% of recirculation rate, the removal efficiency reached 80% at pH 11. The negative effects of bicarbonate on crystallization were observed in oyster shells. The effects of bicarbonate on rate constant were also investigated by applying these results to experimental equation. The rate constant was decreased at the inverse logarithm bicarbonate concentration.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.24.1-24.1
• /
• 2011

CMP (Chemical Mechanical Planarization)는 고직접도의 다층구조의 소자를 형성하기 위한 표면연마 공정으로 사용되며, pattern 크기의 감소에 따른 공정 중요도는 증가하고 있다. 반도체 소자 제조 공정에서는 낮은 비용으로 초기재료를 만들 수 있고 우수한 성능의 전기 절연성질을 가지는 산화막을 만들 수 있는 단결정 실리콘 웨이퍼가 주 재료로 사용되고 있으며, 반도체 공정에서 실리콘 웨이퍼 표면의 거칠기는 후속공정에 매우 큰 영향을 미치므로 CMP 공정을 이용한 평탄화 공정이 필수적이다. 다결정 실리콘 박막은 현재 IC, RCAT (Recess Channel Array Transistor), 3차원 FinFET 제조 공정에서 사용되며 CMP공정을 이용한 표면 거칠기의 최소화에 대한 연구의 필요성이 요구되고 있다. 본 연구에서는 알칼리성 슬러리를 이용한 단결정 및 다결정 실리콘의 식각 및 연마거동에 대한 특성평가를 실시하였다. 화학적 기계적 연마공정에서 슬러리의 pH는 슬러리의 분산성, removal rate 등 결과에 큰 영향을 미치고 연마대상에 따라 pH의 최적조건이 달라지게 된다. 따라서 단결정 및 다결정 실리콘 연마공정의 최적 조건을 확립하기 위해 static etch rate, dynamic etch rate을 측정하였으며 연마공정상의 friction force 및 pad의 온도변화를 관찰한 후 removal rate을 계산하였다. 실험 결과, 단결정 실리콘은 다결정 실리콘보다 static/dynamic etch rate과 removal rate이 높은 것으로 나타났으며 슬러리의 pH에 따른 removal rate의 증가율은 다결정 실리콘이 더 높은 것으로 관찰되었다. 또한 다결정 실리콘 연마공정에서는 friction force 및 pad의 온도가 단결정 실리콘 연마공정에 비해 상대적으로 더 높은 것으로 나타났다. 결과적으로 단결정 실리콘의 연마 공정에서는 화학적 기계적인 거동이 복합적으로 작용하지만 다결정 실리콘의 경우 슬러리를 통한 화학적인 영향보다는 공정변수에 따른 기계적인 영향이 재료 연마율에 큰 영향을 미치는 것으로 확인되었으며, 이를 통한 최적화된 공정개발이 가능할 것으로 예상된다.