• Geophysics and Geophysical Exploration
• /
• v.20 no.4
• /
• pp.207-215
• /
• 2017

To develope shale play which is one of unconventional energy resources, horizontal drilling and hydraulic fracturing are necessary and those are applied to the place where the differential horizontal stress ratio (DHSR) is low. The differential horizontal stress ratio is generally calculated by the minimum and maximum horizontal stress, but it is also calculated from dynamic elastic constants and anisotropic parameters. In this study we analyzed anisotropic properties through the core samples from Danyang limestone and calculated DHSR. The three types of core samples shaped in three directions (vertical, parallel and 45 degree to bedding) were used for laboratory test. We measured P-, S-wave velocities, and density and then calculated dynamic elastic constants, compliance and DHSR. According to the results of the core sample analysis the calculated DHSR is 0.185. Thomsen parameters of the Danyang limestone used in this study are characterized by the P- and S-wave velocities varying along the bedding symmetry axis. It is observed that the DHSR value is more affected by the change in compliance value than the Poisson's ratio. It is necessary to measure SH-wave velocity for more correct petrophysical properties.

• The Journal of Engineering Geology
• /
• v.26 no.3
• /
• pp.339-352
• /
• 2016

The best way of investigating the physical and mechanical properties of subsurface materials is the combined interpretation of data from borehole geophysical surveys and geotechnical experiments with rock samples. In this study two surface seismic surveys with refraction and surface-wave method are alternatively conducted for downhole seismic surveys in test site for geological field trip in Jeungpyung, Chungbuk. P- and S-wave velocity structures are delineated by refraction and MASW (multichannel analysis of shear waves) methods, respectively. Possion's ratio section, reconstructed from P- and S-wave velocities, is correlated to the outcrop geological features consisting of reddish sedimentary rock, gray volcanic rock, and joints/fractures. In addition, rock samples representative for reddish sedimentary and gray volcanic features are geotechnically analyzed to provide physical, mechanical properties, and elastic modulus. Dynamic elastic moduli estimated from geophysical data is found to be higher than the one from geotechnical data. Reddish sedimentary rock characterized with low porosity and moisture content corresponds to the zone of low electrical resistivities and their small variations in the resistivity sections between the rainy and dry days. This trend suggests that the weathered gray volcanic rock and the nearby fractures with higher low porosity and moisture content are interpreted to be good carrier especially in rainy season.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2006.06a
• /
• pp.225-231
• /
• 2006

As a study of efficient velocity analysis in sonic log, several preexisting techniques have been adopted to the sonic data taken from model borehole in Kangwon National University, and the results were compared. For the data taken from monopole source, Slowness-Time Coherence method which is a common technique for nondispersive wave was used. For the data taken from dipole source, conventional STC and Tang's method(Tang et al., 1995) were used. From the good matches in the P and Stoneley wave velocities, we could confirm the effectiveness of STC computation. We also could find that shear velocity obtained from Tang's method were exactly matched with shear velocity obtained from monopole source, and that the velocity were within the range of S wave velocity values obtained from conventional STC application to dispersive flexural waves.

• Journal of the Korean Geophysical Society
• /
• v.10 no.1
• /
• pp.1-12
• /
• 2007

A method to quickly estimate broadband moment magnitudes (Mwp) to warn regional and teleseismic tsunamigenic earthquakes is tested for application of the method to the different seismic observation environment. In this study, the Mwp is calculated by integrating far-field P-wave or pP-wave of vertical component of displacement seismograms in time domain from earthquakes, having magnitude greater than 5.0 and occurred in and around the Korean peninsula from 2000 to 2006. We carefully set up the size of the time window for the computations to exclude S wave phases and other phases following after the P wave phase. The P wave velocities and the densities from the averaged Korean crustal model are used in the computations. Instrumental correction was performed to remove dependency on the seismograph. The Mwp after the instrumental correction is about 0.1 greater than the Mwp before the correction. The comparison of our results to the those of foreign agencies such as JMA and Havard CMT catalogues shows a higher degree of similarity. Thus our results provide an effective tool to estimate the earthquake size, as well as to issue the necessary information to a tsunami warning system when the effective earthquake occurs around the peninsula.

• The Journal of Engineering Geology
• /
• v.8 no.2
• /
• pp.131-143
• /
• 1998

The study area, Beulgok-myon Nonsan-goon Chungcheongnan-do is consist of Changri slate(Och, okcheon system), lithic tuff(Kslt, kyoungsang system), granite (Kqb, kyoungsang system) and quartz porphyry(Kgf, kyoungsang system). More than 3000 joints were measured and classified by direction. Main dipdirection/dips of Kqb are 228~257/73~88, 010~150/70~85, Och are 134~164/40~90, 214~249/55~89, Kslt are 291~332/75~82, 235~241/73~71. But Kgf are not appeared distinct directions of joint. In field, p-wave velocities(Vp) are measured on the bed rock. Vp of Kgf are $5000m(240^{\circ})~2380(360^{\circ})m/s$, Kqb are $3846(210^{\circ})~1408(150^{\circ})m/s$, Kslt are $5000(360^{\circ})~2323(150^{\circ})m/s$ and Och are $6657(180^{\circ})~2000(030^{\circ})m/s$. Also P-wave velocities on specimen are measured. It is slightely higher than it's measured on the bed rock. For engineering properties of rock, we measured Poisson's ratio, rigidity, Young's modulus and bulk modulus by dynamic method.

• Geophysics and Geophysical Exploration
• /
• v.9 no.3
• /
• pp.185-192
• /
• 2006

Cares should be taken when performing the P and S wave velocity loggings in engineering and environmental fields. Some of them are the effect of casing, which is installed to prevent the borehole collapsing when the drilling is done on the loose ground such as soil and/or soft rock, and the discrepancy of the velocities of the same media according to the difference of the source wave frequency spectrum. The elastic moduli obtained from the P and S wave velocity logging have the dynamic characteristics. To overcome these difficulties, the following suggestions are recommended; (1) develop and apply a careful drilling technique that can keep the borehole wall without a casing, and (2) apply the logging methods with the suitable frequency bandwidth for the object of the velocity logging. It is important to make the aseismological engineers understand the difference between the dynamic elastic moduli and the static ones obtained from mechanical test, and to advise them to use the information properly.

• Journal of the Korean earth science society
• /
• v.30 no.4
• /
• pp.401-408
• /
• 2009

We carried out the Suspension PS log and gamma-gamma log in andesite and sedimentary rocks distributed near the area of Myodo-dong, Yeosu. The main purpose of this study was to find out the distribution of seismic velocities and densities and to analyze the correlation of the two rocks by comparing their geophysical well logs with rock cores. The distributions of P and S-wave velocities for two rocks represented in the study area showed a difference of about 2,000 m/sec and 1,500 m/sec with depth, respectively, while the distributions of densities had a discrepancy of about $0.35g/cm^3$ with depth. However, the results of geophysical well logs analysis were similar to the two rocks. Consequently, it is clear that these results are interpreted as a difference due to weathering rather than rock type. In particular, the RQD values showed a good correlation to geophysical well log data.

• Economic and Environmental Geology
• /
• v.16 no.1
• /
• pp.51-61
• /
• 1983

By using local earthquake data, the Korean crust model and travel-time tables were determined. The upper crustal earthquakes (Hongsung event and Ssanggyesa event) were considered as auxiliary information, and the lower crustal earthquakes (Uljin event and Pohang event) played an important role in determining model parameters. The possible existence of Low Velocity Layer (LVL) in the upper mantle was suggested by discrepancy in the arrival times of Sariwon earthquake which occurred below Moho discontinuity. Computer program for the determination of the model parameters was developed in order to screened out the optimum parameters by comparing the travel times of observed data with theoretical ones. We found that the discontinuities of Conrad, Moho, and upper and lower boundaries of LVL have their depth of 15, 32, 55 and 75 Km, respectively. The velocities of P-and S-wave in the layers between those discontinities were found to be (1) 5.98, 3.40 Km/sec (2) 6.38, 3.79 Km/sec (3) 7.95, 4.58 Km/sec (4) unknown (5) 8.73, 5.05 Km/sec, respectively from the top layer. Travel-time tables were also computed for the inter-local earthquakes which have their direct wave paths above the LVL.

• 한국방재학회:학술대회논문집
• /
• 2007.02a
• /
• pp.137-139
• /
• 2007

To enhance capability on discerning local and regional seismic phases, such as, Pn, Pg, Sn, Rg, etc, within the crust, 2-D numerical forward modeling will be applied to the data obtained from local seismic stations by simulating almost all waves including not only body wave but also surface wave generated without having to explicitly include them under consideration of Q factor. In this study, after getting rid of instrumental response by deconvolution, pseudo-spectral method instead of relying on typical numerical methods, such as, FEM(Finite Element Method) and FDM(Finite Difference Method), will be implemented for 2-D numerical forward modeling by considering velocities of P-wave and S-wave, density, and Q factors. Ultimately, the Power of reaching the enhanced capability on discerning local and regional seismic phases will make it easier for us to identify the seismic source, whether it is originated from man-made explosion or pure earthquake.

• Economic and Environmental Geology
• /
• v.56 no.3
• /
• pp.277-291
• /
• 2023

To analyze the crustal velocity structures beneath 21 broadband seismic stations in Gangwon Province, South Korea, we first applied the H-κ stacking method to 139 teleseismic event data (Mw ≥ 5.8 and the epicentral distance of 30° - 90°) occurring between March 18, 2019 and December 31, 2022 to estimate the Moho depths and V_p/V_s ratios beneath each station. The Moho depths and V_p/V_s ratios from the H-κ stacking method range from 24.9 to 33.2 km depth and 1.695 - 1.760, respectively, and the estimated V_p/V_s ratios were applied to the joint inversion of receiver functions and surface wave dispersion to obtain 1-D crustal velocity models beneath each station. The resulting Moho depths range from 25.9 to 33.7 km depth, similar to the results from the H-κ stacking method. Moho depth results from the both methods are generally consistent with Airy's isostasy. The 1-D crustal velocity models confirm that the existence of 2 km thick low-velocity layers with P-wave velocities of 5 km/s or less at some stations in the Taebaeksan basin, and at the stations CHNB and GAPB in northern Gangwon Province, which are located above the Cenozoic sedimentary layer. The station SH2B, although not overlying a sedimentary layer, has a low P-wave velocity near the surface, which is probably due to various factors such as weathering of the bedrock. We also observe a velocity inversion with decreasing velocity with depth at all stations within 4 - 12 km depths, and mid-crustal discontinuities possibly due to density differences in the rocks at around 10 km depth below some stations.