• 한국환경과학회지
• /
• 제9권6호
• /
• pp.511-515
• /
• 2000

The purpose of this experiment is to prepare ethylene propylene diene terpolymer(EPDM)/ acrylonitrile butadiene rubber(NBR) blend which represents good environmental resistant properties including favorable oil and ozone resistance. With incorporation of EPDM, NBR and other ingredients, the rubber and chemical additives were mixed by mechanical method such as Banbury mixer and open 2-roll mill. Then rubber vulcanizates were manufactured by hot press and mechanical properties, oil and ozone resistance of the test specimens were measured. The oil resistance and ozone resistance of EPDM and NBR, respectively, is remarkably improved by blending EPDM with NBR. The optimum results of oil and zone resistant characteristics were obtained at EPDM/NBR(=25/75 wt%) composition ratio.

• 한국환경과학회지
• /
• 제13권4호
• /
• pp.421-427
• /
• 2004

With the help of mechanical mixing method such as Banbury mixer and open 2 roll mill, ethylene propylene diene terpolymer (EPDM) was blended with the chloroprene rubber (CR) then mechanical properties and ozone resistance test of blends were subsequently investigated. It was noted that the hardness increased with an increasing of CR contents. Generally the hardness was increased with heat aging time most likely due to the post cure. In ozone resistance test of blend, after 8 hours a portion of fine crack is obtained for pure CR. It is confirmed that ozone resistance is greatly improved by addition of 25wt% EPDM to CR.

• 한국환경과학회지
• /
• 제10권1호
• /
• pp.73-77
• /
• 2001

This study examined blends of styrene butadiene rubber(SBR) and chloroprene rubber(CR) prepared from an open 2-roll mill following the conventional polymer blend method for a wide range of the blend composition. Rubber vulcanizates were manufactured by hot press and then mechanical properties, heat and ozone resistance of the specimens were examined. Due to the post cure during the aging test, hardness of vulcanizates was increased. It was found that the undesirable characteristics of heat and ozone resistance of pure SBR was significantly improved through the blending of SBR with CR.

• Elastomers and Composites
• /
• 제45권1호
• /
• pp.44-50
• /
• 2010

기계적 혼련법으로 butadiene rubber(BR)과 대표적인 결정성고무인 chloroprene rubber(CR) 블렌드 혼련물을 제조하여, 이들의 가교 거동, 기계적 성질, 내오존성 및 동적 기계적 성질 등을 검토하였다. 내오존시험에 있어서 50 wt% CR 고무의 첨가에 의하여 크게 개선됨을 확인할 수 있었다. Rheovibron에 의한 동적 계적 특성 측정의 결과로부터 BR/CR 블렌드는 두 개의 전이를 보였으며 $tan{\delta}$ 피이크의 위치는 CR 고무의 함량이 증가함에 따라 고온 쪽으로 이동함을 확인할 수 있었다. 한편 CR 고무량이 증가할수록 최적 가황시간이 증가하는 경향을 보였다.

• Elastomers and Composites
• /
• 제43권1호
• /
• pp.8-17
• /
• 2008

Styrene-butadiene rubber(SBR)은 내마모성, 상용성, 방진성이 우수 하지만, SBR은 주쇄의 불포화기때문에 오존에 의해 쉽게 손상을 받고 탄화수소에 쉽게 팽윤되어 점탄성을 잃어버려 고무제품으로서의 수명을 단축시킨다. 따라서, 본 연구의 목적은 SBR 고무의 이러한 단점을 보완하기 위함이다. 내오존성과 기계적물성을 개선시키기 위해서 내오존성이 우수한 ethylene-propylene-diene terpolymer(EPDM)을 다양한 비율로 블렌드하고, 방진제품으로써의 적합성을 고려하기 위하여 다양한 분석기술을 사용하여 경도, 열분해 온도, 모폴러지, 유리전이온도, 내오존성, 정적 스프링정수를 측정하였다. 본 실험을 통하여 SBR과 EPDM 블렌드의 조성변화에 따른 특성을 연구한 결과, SBR에 대하여 EPDM 30% 블렌드시 상용성이 우수하고, 내오존성이 증가하는 것을 알 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.890-893
• /
• 2001

Two-layer self bonding insulating tape consists of butyl rubber(IIR ; Isobutylene-isoprene rubber) adhesive layer and polyethylene protective film. Butyl rubber have inherent characteristics such as resistance to corrosion and water, low temperature flexibility, excellent electrical insulating properties also resistance to environmental effect such as ozone and ultraviolet. Polyethylene film was used for the purpose of good insulating properties and resistance to ozone and ultraviolet. The tape was manufactured using extrusion and calender method.

• Elastomers and Composites
• /
• 제46권4호
• /
• pp.329-334
• /
• 2011

일반적으로 butyl 고무(IIR : isobutylene isoprene rubber)는 우수한 내기체투과성 및 저반발 탄성체로서 우수한 충격흡수성을 갖는다. 본 실험에서는 butyl고무에 EPDM(ethylene propylene diene monomer)을 기계적 혼련법으로 blend 혼련물을 제조하여 이들의 가교 거동, 물리적 성질 및 내오존성 등을 측정하였다. EPDM 고무량이 증가할수록 최적 가황시간이 단축되는 경향을 보였다. 기체투과속도 테스트에 의한 내기체투과성 측정 결과 butyl고무량이 50 wt% 이상일 경우에는 기체투과도가 현저히 감소하였다. 한편 butyl rubber/EPDM 블렌드의 경우에 EPDM의 함량이 25 wt.% 이상 함유될 경우 내오존성이 향상되어 50 pphm, $50^{\circ}C$, 120시간 조건에서도 아무런 표면변화가 없었다.

• Elastomers and Composites
• /
• 제53권3호
• /
• pp.168-174
• /
• 2018

Natural rubber (NR) and bromo-isobutylene-isoprene rubber (BIIR) were compounded with other formulation chemicals through polymer blending via a mechanical mixing method. After rubber vulcanization by hot-press compression molding, the cure characteristics, mechanical properties, and ozone resistance of the NR/BIIR blends were measured. As the BIIR content increased, the maximum torque of the blends decreased, while the optimum cure time and scorch time tended to increase. Furthermore, the hardness of the blends increased with increasing BIIR content, reaching the maximum value at 75 wt% BIIR, and decreased with a further increase in the BIIR loading. The tensile strength and elongation at break decreased with an increase in the BIIR content, reaching the minimum value at 75 wt% BIIR, and increased with a further increase in the BIIR content. In the ozone resistance test, cracks were not generated when the BIIR content was more than 75 wt%.

• Elastomers and Composites
• /
• 제43권2호
• /
• pp.104-112
• /
• 2008

통상적인 고무블렌드 방법에 따라 개방식 2-롤밀을 사용하여 ethylene propylene diene terpolymer (EPDM)과 styrene butadiene rubber (SBR) 블렌드 배합물을 제조하여, 이들의 경화 특성, 기계적 성질 및 내오존성 등을 검토하였다. SBR함량이 증가할수록 가황곡선의 토크가 증가하였다. 최대 토크는 SBR 25wt% 일 때 가장 낮았으며 그 이상의 SBR 량에서는 직선적으로 증가하였다. 스코치시간 및 최적경화시간은 SBR고무 함량이 증가함에 따라 감소하였다. 경도는 SBR 함량이 50wt% 일 때 최고값을 보였으며 그 전후에서는 감소하는 경향을 보였다. 내오존시험에 있어서 소량의 EPDM 고무의 첨가에 의하여 내오존성이 크게 개선됨을 확인할 수 있었다.

• 마이크로전자및패키징학회지
• /
• 제21권1호
• /
• pp.41-44
• /
• 2014

We employed UV-Ozone treatment method for the fabrication of dense and highly conductive nanoparticle thin films. We demonstrated the UV-Ozone treatment effect on the silver nanoparticle thin films as a function of time and temperature. The capping layers of nanoparticles were decomposed after UV-Ozone treatment and dense nanoparticle thin films were obtained. Moreover, electrical and mechanical properties of the thin films after UV-Ozone treatment were measured by using resistance measurements under tension in an in-situ tensile tester. The initial resistance of nanoparticle thin films was decreased by 82.6% with optimized UV-Ozone treatment condition of $150^{\circ}C$ for 20 minutes.