• Journal of Ginseng Research
• /
• v.33 no.4
• /
• pp.355-360
• /
• 2009

Phenanthrene ($C_{14}H_{10}$) is a polycyclic aromatic hydrocarbon with three aromatic rings, and it can be produced by incomplete combustion of fossil fuels. Comet assay was used to examine the oxidative DNA damage of lymphocytes by phenanthrene and to measure the suppressive effects of ginseng extract on the DNA damage in this investigation. The in vitro oxidative DNA damage by phenanthrene increased in a dose-dependent manner in the lymphocyte. However, the DNA damage was significantly inhibited by ascorbate. Moreover, pretreatment, cotreatment and posttreatment with ginseng extract enhanced lymphocyte resistance to the phenanthrene-induced DNA damage. Phenanthrene enhanced the generation of intracellular reactive oxygen species, and the elevated reactive oxygen species level was reduced by treatment with ginseng extract.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.6
• /
• pp.45-52
• /
• 2021

A hot-firing test was conducted using gaseous-methane and gaseous-oxygen under highly fuel-rich condition as a prior study for the development of a liquid propellant small rocket engine. To compare combustion characteristics for various equivalence ratios, the oxygen flow rate was set to 12 g/s and the methane flow rate was changed according to the equivalence ratio. As a result, it was observed that the steady-state characteristic velocity obtained during the hot-firing test steeply rose in the latter part of each test: the difference between the former and the latter steady value was enhanced overall in proportion to the equivalence ratio. Based on this, the equivalence ratio range depending on the variational characteristics of the characteristic velocity could be divided into three combustion regimes.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.37-44
• /
• 1998

Lean burn combustion is an important concept for improving the fuel consumption and exhaust emissions. However, the lean burning is associated with increased cycle-to-cycle combustion variations due to the ignition instabilities and redu- ced flame propagation rates. Engine stability under lean mixture conditions could be improved by increasing flame speed through enhanced flow characteristics and by securing ignitability with improvement of ignition systems. The effects of flow motion and ignition characteristics on the combustion performances were investigated in a 4-valve SI engine. Flow motions of tumble-swirl were varied with a swirl control valve attached at the inlet ports, while ignition energy and its distribution were controlled in a high -frequency ignition system by changing spark duration and spark frequency. The improvement of lean burn performance by the optimum flow motion and ignition characteristics is discussed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.472-474
• /
• 2012

The hot-firing tests of a subscale gas generator were successfully performed to investigate the effect of injector shape variation on its discharge coefficient. The test results showed that discharge coefficient of liquid oxygen injectors was enhanced significantly. However, the combustion instability of low-frequency fluctuation occurred at low and design pressure conditions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.5 s.236
• /
• pp.617-624
• /
• 2005

An analysis of the effects of $CO_{2}$ on fundamental combustion characteristics was performed in Oxygen enriched condition by comparing the laminar burning velocities, flame structures, fuel oxidation paths. Fictitious $CO_{2}$ was introduced to discriminate the chemical reaction effects of $CO_{2}$ from the thermal effects. PREMIX code was utilized to evaluate the laminar burning velocities. OPPDIF code was utilized to investigate the flame structure and fuel oxidation path variation. The contributions of thermal effects on laminar burning velocities are dominant at lowly oxygen-enriched condition but those of chemical reaction effects become dominant at highly oxygen-enriched condition. Chemical reaction effects caused the additional flame temperature decrease besides thermal effects and oxygen-leakage increase in non-premixed flame. Specific fuel oxidation path and CO production path is enhanced in spite of overall decrement of fuel consumption rate by chemical reaction effects of$CO_{2}$.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.149-154
• /
• 2001

The emission characteristics, flame stability, the composition of the flame zone and temperature profile were studied experimentally. The compositions of oxydant were varied by substituting $N_2$ with $CO_2$ at the constant $O_2$ concentration. Results showed that flame became unstable due to the high heat capacity, low transport rate and strong radiation effect of $CO_2$ in comparison with those of $N_2$. The reaction zone was cooled, broadened, as the conversion ratio of $CO_2$ to $N_2$ was increased. Temperature has a large effect on the NOx emission. The concentration of NOx in flue gas decreased due to the decreased temperature of reaction zone. It was also shown that the reaction was delayed by the cooling effect. As the conversion ratio of $CO_2$ to $N_2$ was increased, the emission of CO and the higher temperature zone increased due to the decrease of reaction rate by the cooling effect.

• Journal of the Korean Ceramic Society
• /
• v.56 no.5
• /
• pp.497-505
• /
• 2019

Lanthanum-based transition metal cations containing perovskites have emerged as potential catalysts for the intermediate-temperature (600-800℃) oxygen reduction reaction (ORR). Here, we report a facile acetylacetone-assisted combustion route for the synthesis of nanostructured La_0.6Sr_0.4Co_0.2Fe_0.8O_3-δ (LSCF6428) cathodes for intermediate-temperature solid-oxide fuel cells (IT-SOFCs). The as-prepared powder was analyzed by thermogravimetry analysis-differential scanning calorimetry. The powder calcined at 800℃ was characterized by X-ray diffraction, scanning electrode microscopy, energy dispersive X-ray spectroscopy, and Brunauer-Emmett-Teller surface area measurements. It was found that the porosity of the air electrode significantly increased by utilizing the nanostructured LSCF6428 instead of commercial powder. The performance of a single cell fabricated with the nanostructured LSCF6428 cathode increased by 112%, from 0.4 to 0.85 W cm^-2, at 700℃. Electrochemical impedance spectroscopy showed a considerable reduction in the area-specific resistance and activation energy from 133.5 to 61.5 kJ/mol, resulting in enhanced electrocatalytic activity toward ORR and overall cell performance.

• Transactions of the Korean hydrogen and new energy society
• /
• v.16 no.3
• /
• pp.229-237
• /
• 2005

A new burner configuration for a compact fuel-cell reformer with a high-temperature air combustion concept was numerically studied. The burner was designed for a 40 $Nm^3/hr$ hydrogen-generated reformer using natural gas-steam reforming method. In order to satisfy the primary requirements for designing a reformer burner (uniform distribution of temperature along the fuel processor walls and minimum heat losses from the reformer), the features of the present burner configuration included 1) a self-regenerative burner for an exhaust-gas-recirculation to apply for the high-temperature air combustion concept, and 2) an annular-type shield for protecting direct contact of flame with the processor walls. For the injection velocities of the recirculated gas of 0.6-2.4 m/s, the recirculated gas temperature of 1000 K, and the recirculated oxygen mole fraction of 4%, the temperature distributions along the processor walls were found uniform within 100 K variation. Thus, the present burner configuration satisfied the requirement for reducing temperature gradients along the processor walls, and consequently demonstrated that the high-temperature air combustion concept could be applied to the practical fuel reformers for use of fuel cells. The uniformity of temperature distribution is enhanced as the amount of the recirculated gas increases.

• Korean Chemical Engineering Research
• /
• v.44 no.4
• /
• pp.404-409
• /
• 2006

The catalytic combustion of toluene over Pd-Cu/USY zeolite has been examined by using FT-IR spectroscopy in a closed system under dry and humid conditions. The catalytic combustion of toluene (700 ppmv) in the temperature range of $80-220^{\circ}C$ has been investigated by using a fixed bed reactor. The Pd-Cu/USY catalyst showed the highest catalytic performance with respects to the PdO-CuO/USY and Pd/USY. Comparing to $PdO/Al_2O_3$ catalysts, the slight improvement in conversion was observed over PdO/USY catalysts under humid condition since USY zeolite is hydrophobic substrate and water give an additional oxygen source to zeolite surface like oxygen. The reduced catalysts showed more enhanced catalytic activity due to the reduced activation energy of combustion of toluene than oxidized catalysts such as PdO/USY and PdO-CuO/USY.

• Journal of the Korean Society of Combustion
• /
• v.17 no.1
• /
• pp.58-65
• /
• 2012

The influence of magnetic field on propane and acetylene diffusion flames have been experimentally investigated using an electromagnetic system. Periodically induced magnetic field having various frequencies and duty ratios was established in square wave form. The maximum intensity and gradient of magnetic field were 1.3 T and 0.27 T/mm, respectively. The width of a propane flame was reduced up to 4.5% and the brightness was enhanced up to 25% when the magnetic field was induced. The soot emission from an acetylene flame was ceased when magnetic field was induced. The alteration of flow field, which is due to the paramagnetic characteristics of oxygen molecule, is most likely to be responsible for the change in flame size and brightness. The effect of magnetic field on diffusion flames, which competes with the gravitational effect, was more apparent from a smaller size flame. The magnetic field effect, therefore, could be important under microgravity conditions. Since the time required to alter the flow field must be finite, the magnetic field effect is likely to be less significant for a periodically oscillating magnetic field at a high frequency or having a small duty ratio.