• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.257-259
• /
• 2002

As a new host material for a red phosphor for PDP applications, has studied (Y,Gd)$Al_3(BO_3)_4$ which gives non-centrosymmetric sites for $Eu^{3+}$ activators. Vacuum ultraviolet (VUV) excitation spectrum of new red phosphor (Y,Gd)$Al_3(BO_3)_4$:$Eu^{3+}$ has two broad bands. One band with the absorption edge at ca. 168 nm is the band-gap absorption of aluminoborate and the other broad band centered 240 nm is the charge transfer transition between $Eu^{3+}$ and the neighboring oxygen anions. The PL spectrum shows the strongest emission at 617 nm due to the electric dipole $^5D_0{\rightarrow}^7F_2$ transition of $Eu^{3+}$, whose luminescent chromaticity is (0.67, 0.33).

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2003.05a
• /
• pp.365-369
• /
• 2003

이산화탄소 규제 대응 전략으로, 배출되는 온실가스를 분리, 회수, 처리하는 연구가 지속적으로 진행되고 있다. 현재 이산화탄소 저감 연구는 공정개발 초기부터 이산화탄소 배출을 방지하거나 분리하기 쉬운 형태로 설계하는 방식으로 전환되고 있다. 그 예로 고온 순산소 연소 시스템이 제안되었다. 이는 $CO_2$를 가장 효과적으로 저감시키는 방법 중의 하나로 연소에 사용되는 산화제로 순산소를 사용하여 원료를 절감할 수 있고 산소를 사용하기 때문에 배가스 중에 질소분율이 감소하여 배가스에 의한 현열손실을 줄일 수 있으며 또한 배가스 현열을 회수하여 산소를 고온으로 예열시켜 에너지를 추가적으로 절감할 수 있다. 이를 위해 산소를 선택적으로 투과시켜 고순도 산소를 제조할 수 있을 뿐만 아니라 산소제조 장치비를 절감할 수 있는 ITM (Ion Transport Membrane) 신소재 및 산소 투과 공정을 개발하고자 한다.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.99-102
• /
• 2003

Many researches on synthesis process for BSCCO precursor powders have been developed for high J$_{c}$ BSCCO-2223/Ag tape. Spray pyrolysis method for fabrication of precursor powder has many advantages, such as high purity, fine particle size of BSCCO precursor powder. Fine, spherical powders were prepared by ultrasonic spray pyrolysis from the aqueous solution of metal nitrates. BSCCO precursor powders were synthesized with 0.1 M concentration and heat treatment conditions. Average particle size for spray pyrolysis powders was 1.5 ~ 3 ${\mu}{\textrm}{m}$. BSCCO -2223/Ag tape was prepared by PIT method and followed by various sintering conditions. The critical current density of BSCCO-2223/Ag tape sintered in low oxygen partial pressure was ~ 23 kAcm$^{-2}$.

• Journal of Platform Technology
• /
• v.10 no.3
• /
• pp.3-10
• /
• 2022

The effectiveness of an innovative skin treatment system that delivers an anti-aging solution deep into the skin without invasiveness and pain using a non-invasive air technology was investigated. In addition, an effective change using a non-invasive technique for delivering a solution for skin improvement was confirmed. The equipment named Cellre Jet is an effective skin care and drug delivery equipment that instantly opens the skin epidermis by using a maximum output pressure of 6 bars and high-pressure purified oxygen of 75-90% purity to deliver various nano-sized vital substances deep into the skin, and it uses the method of precisely controlling the equipment through an 8-inch digital touch display to accurately dispense the prescribed dosage. In this study, changes in skin condition were analyzed using this equipment and nano ampoules on subjects with actual skin problems through a related comparison and effectiveness judgment program. Through this study, skin care and drug delivery are possible, which will contribute to verifying the effectiveness of this non-invasive drug delivery equipment in the future, and is expected to establish the systematic effect in observing and studying changes in the skin.

• Archives of Metallurgy and Materials
• /
• v.64 no.3
• /
• pp.959-962
• /
• 2019

This study was carried out to evaluate the aspect of microstructure and mechanical property development on additive manufactured pure Ti at elevated heat-input. For this work, pure Ti powder (commercial purity, grade 1) was selected, and selective laser melting was conducted from 0.5 to 1.4 J/mm. As a result, increase in heat-input led to the significant grain growth form 4 ㎛ to 12 ㎛, accompanying with the change of grain shape, correctly widmanstätten structured grains. In addition, Vickers microhardness was notably increased from 228 Hv to 358 Hv in accordance with elevated heat-input, which was attributed to the increased concentration of oxygen and nitrogen mainly occurred during selected laser melting process.

• Journal of the Korean Society of Industry Convergence
• /
• v.7 no.3
• /
• pp.259-263
• /
• 2004

In the manufacture progress of LCD or semiconductor, there are used many kinds of gas like erosion gas, dilution gas, toxic gas as a progress which used these gas there are required high puritize to increase accumulation rate of semiconductor or LCD materials work progress of semiconductor or LCD it demand many things like the material which could minimize metallic dust that could be occured by reaction between gas and transfer pipe laying material, illumination of the surface, emition of the gas, metal liquation, welding etc also demand quality geting stricted. Material-Low-sulfur-contend (0.007-0010), vacuum-arc-remelt(VAR), seamless, high-purity tubing material is recommend for enhance welding lower surface defect density All wetted stainless steel surface must be 316LSS elecrto polishinged with ${\leq}0.254{\mu}m$($10.0{\mu}in$) Ra average surface finish, $Cr/Fe{\geq}1.1$ and $Cr_2O_3$ thickness ${\geq}25{\AA}$ From the AES analytical the oxide layer thickness (23.5~36 angstroms silicon dioxide equivalent) and chromum to iron ratios is similar to those generally found on electropolished stainless steel., molybdenum and silicon contaminants ; elements characteristic of stainless steel (iron, nickel and chromium); and oxygen were found on the surface Phosphorus and nitrogen are common contaminants from the electropolish and passivation steps.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.3
• /
• pp.93-97
• /
• 2015

To synthesis of high purity micro silver particle, we extracted the silver from the waste by liquid-liquid extraction and used the rapid firing-liquid phase precursor (RF-LPP) method. The silver micro particle was synthesized at $500^{\circ}C$ for 3 hr in air atmosphere by RF-LPP method. As a result of the research, micro silver particle is measured X-ray diffraction (XRD), the main peak is nearly corresponded to the same as JCPDS card (No.87-0719). With using the RF-LPP method, the fine Ag micro particle indicated due to the control of nucleation site and the oxygen contents was decreased by reducing treatment. We expect this research contribute to advance in field of the recycling technology.

• Journal of Korean Society on Water Environment
• /
• v.38 no.5
• /
• pp.220-230
• /
• 2022

Seasonal variability of water quality in the upland headwater streams in ten forested catchments (37.0~209.0 ha) was examined from April to November 2021. Here, seven physicochemical parameters were analyzed including pH, electrical conductivity (EC), biochemical oxygen demand (BOD), chemical oxygen demand (COD), total nitrogen (T-N), total phosphorous (T-P), and BOD/TOC. The parameters were compared with those of lowerland rivers as middle and lower reaches within a watershed. The pH showed was low (6.4~6.9) during all the seasons, however, BOD and BOD/TOC in the fall season were 2-fold higher than in the spring and summer seasons. Based on environmental standards, the water quality level revealed that the upland headwater streams maintained the purity and cleanliness of water except for pH in the summer season. BOD/TOC of all the seasons and BOD of the fall season in the upland headwater streams were higher than that in the lowerland rivers, whereas the rest of the physicochemical parameters in the upland headwater streams were lower than that in the lowerland rivers. Additionally, the water quality level maintained the purity and cleanliness of water as "Good" in two reaches. The unique aspects of our study design enabled us to draw inferences about water quality characteristics with temporal and spatial analysis in upland headwater streams. This design will be useful for the long-term strategy of effective water quality management for integrated upland headwater streams and lowerland rivers within a watershed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.61-69
• /
• 2000

Indium-Tin Oxide (ITO) films were prepared on the commercial glass substrate by the Magnetron Sputtering method. The target was a 90wt.% $In_2O_3$-10wt.% $SnO_2$with 99.99% purity. The ITO films deposited by changing the partial pressure of oxygen gas ($O_2$/(Ar+$O_2$)) of 2, 3 and 5% as well as by changing the substrate temperature of $300^{\circ}C$ or $500^{\circ}C$. The influence of substrate pre-annealing and pre-cleaning on the quality of ITO film were examined, in which the substrate temperature was $500^{\circ}C$ and oxygen partial pressure was 3%. The characteristics of films were examined by the 4-point probe, Hall effect measurement system, SEM, AFM, Spectrophotometer, and X-ray diffraction. The optimum ITO films have been obtained when the substrate temperature is $500^{\circ}C$ and oxygen partial pressure is 3%. At optimum condition, the film showed transmittance of 81%, sheet resistivity of $226\Omegatextrm{cm}^2$, resistivity($\rho$) of $5.4\times10^{-3}\Omega$cm, carrier concentration of $1.0\times10^{19}cm^{-3}$, and carrier mobility of $150textrm{cm}^2$Vsec. From XRD spectrum, c(222) plane was dominant in the case of substrate temperature at $300^{\circ}C$, without regarding to oxygen partial pressure. However, in the case of substrate temperature at $500^{\circ}C$, c(400) plane was grown together with c(222) plane, only for oxygen partial pressure of 2 and 3%. In both case of chemical and ultrasonic cleaning without pre-annealing the substrate, it showed much almost same sheet resistivity, resistivity($\rho$), transmittance, carrier concentration, and carrier mobility. In case of $500^{\circ}C$/60min pre-annealing before ITO film deposited, both transimittance and carrier mobility are better than no pre-annealing, because pre-annealing is supposed to remove alkari ions diffusion from substrate. ITO film deposited on the Corning 0080 sybstrate showed a little bit better sheet resistivity, resistivity($\rho$), transimittance, carrier concentration than the film deposited on commercial glass. But no differences between Corning substrate and pre-annealed commercial glass substrate are found.

• Clean Technology
• /
• v.27 no.1
• /
• pp.9-16
• /
• 2021

Since the active matrix organic light-emitting diode (AMOLED) encapsulation process is very vulnerable to moisture and oxygen, high-purity nitrogen with minimal moisture and oxygen must be used. In this study, a copper-based catalyst used to remove oxygen from nitrogen in the AMOLED encapsulation process was optimized. Two-component and three-component catalysts composed of CuO, Al2O3, or ZnO were prepared through a co-precipitation method. The prepared catalysts were characterized by using BET, XRD, TPR, and XRF analysis. In order to verify the oxygen removal performance of the catalyst, several catalytic reactions were conducted in a fixed bed reactor, and the corresponding oxygen contents were measured through an oxygen analyzer. In addition, reusability of the catalysts was proven through repetitive regeneration. The properties and oxygen removal capacity of the catalysts prepared with CuO and Al2O3 ratios of 6 : 4, 7 : 3, and 8 : 2 were compared. The number of active sites of the catalyst with a ratio of CuO and Al2O3 of 8 : 2 was the highest among the 2-component catalysts. Moreover, the reducibility of the catalyst with a ratio of CuO and Al2O3 of 8 : 2 was the best as it had the highest CuO dispersion. As a result, the oxygen removal ability of the catalyst with a ratio of CuO and Al2O3 of 8 : 2 was the best among the 2-component catalysts. The best oxygen removal capacity was obtained when 2wt% of ZnO was added to the sub-optimized catalyst (i.e., CuO : Al2O3 = 8 : 2) probably due to its outstanding reducibility. Furthermore, the optimized catalyst kept its performance during a couple of regeneration tests.