• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.155-155
• /
• 2010

Oxygen incorporated $Ge_2Sb_2Te_5$ (GST) films were prepared by an ion beam sputtering deposition (IBSD) method. From the I-V curves, the $V_{th}$ value varies with the oxygen content. Ge-deficient hexagonal phases are responsible for the observed unstability and decrease in $V_h$ values. In the case of a GST film with an elevated oxygen content of 30.8 %, the GST layer melted at 9.02 V due to the instability conferred by the high oxygen content. The formation of Ge-deficient hexagonal phases such as $GeSb_2Te_4$ and $Sb_2Te_3$ appear to be responsible for the $V_{th}$ variation. Impedance analyses indicated that the resistance in GST films with oxygen contentsof 16.7 % and 21.7 % had different origins. Thermal desorption spectroscopy (TDS)data indicate that moisture and hydrocarbons were more readily desorbed at higher oxygen content because the oxygen incorporated GST films are more hydrophilic than undoped GST films.

• Journal of Welding and Joining
• /
• 제16권2호
• /
• pp.93-99
• /
• 1998

The effects of welding conditions of gas metal arc welding on the elements loss of solid wire, oxygen content and impact toughness of weld metals were studied. Deoxidizing elements loss was increased with increase of arc voltage in both short-circuit transfer mode and globular transfer mode. It is believed that increase of arc voltage results in increase of reaction time between elements in the droplet and surrounding gas at the end of wire and in the arc column. Based on the thermodynamic equilibrium model, the oxygen content of weld metal can be predicted with the content of silicon and manganese as following : [%O] = $K([%Si][%Mn])^{-0.25}$, K = -15518/T+6.01. The equilibrium temperature was dependent on shielding gas, and it was 187$0^{\circ}C$ for $CO_2$ gas and 180$0^{\circ}C$ for 20%$CO_2$-80%Ar gas. The oxygen content of weld metal which shows maximum impact toughness was varied with deoxidizing alloy system of wires, 0.041 wt% for Si-Mn type wire and 0.026 wt% for Si-Mn-Ti type wire.

• 한국자기학회지
• /
• 제3권3호
• /
• pp.229-233
• /
• 1993

광자기 디스크의 제조시 기록막내부의 산소함량에 따른 기록 및 자기적 특성의 변화를 연구하였다. 기록막내의 산소함량 변화는 반응성 스퍼터링에 의해 조절하였으며 스퍼터링 전과정 동안 산소의 거동을 in-situ 잔류가스분석기로 조사하였다. 산소함량의 증가에 따라 보자력은 감 소하였으나 수직이방성 및 수직 각형비등은 변화하지 않았다. 대부분의 첨가된 산소는 스퍼터링 과정중 소모되어 Tb원자와 안정한 산화물을 형성하여 자기적 조성의 변화를 초래하였지만 임계기 록크기와 임계외부자계크기에만 약간의 변화를 가져왔을 뿐 디스크의 기록신호잡음비에는 별로 영향을 미치지 않았다. 또한 디스크의 신뢰도면에서도 크게 감소하지 않았다.

• Journal of Nutrition and Health
• /
• 제9권4호
• /
• pp.54-58
• /
• 1976

Vitamin C의 변화는 식품의 가치를 판단하는데 중요한 인자가 된다. 이의 변화는 산소의 존재하에서 일차반응 속도로 분해된다고 알려져 있다. 그러나 제한된 량의 산소 속에서는 이차반응 내지 일차반응으로 설명되기도 한다. 이에 제한된 산소속에서 철, 구리 이온의 존재하에서 관찰한 바 용존산소와는 크게 관계없이 일차 반응속도로 분해되었고 이때 빛의 조사는 촉진적인 인자였었다.

• The Korean Journal of Ceramics
• /
• 제6권1호
• /
• pp.68-73
• /
• 2000

The effects of oxygen annealing on the carbon content in MgO thin films were investigated, MgO thin films were deposited on Si(100) substrate at different temperatures of 400 to $700^{\circ}C$ and different deposition rates of 3.4 to 11.6$\AA$/min. Using rf magnetron sputtering method. Carbon content change on the surface of MgO thin films with the oxygen annealing at different temperatures was investigated using various method. The carbon content decreased as the annealing temperature increased. $Pb(Zr_{0.53}Ti_{0.47})O_3$(PZT) thin films were deposited on the MgO/Si(100) substrates. The effects of carbon content on the phase formation and the electrical properties of PZT thin films were also investigated.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.759-760
• /
• 2006

Ti-6Al-4V has low specific gravity, high corrosion resistance and superior mechanical properties but it is very difficult to control oxygen content in MIM process. It is necessary to use powders with coarse particle size to decrease oxygen content of powders, so feedstocks with poor fluidity and sintered bodies with lower density are obtained in such cases. Fine titanium hydride-dehydride powders were blended with atomized powders to accomplish higher fluidity and sintered density. Sintered bodies had higher sintered density and mechanical properties equivalent to those of wrought materials by controlling oxygen content less than 0.35mass%.

• The Korean Journal of Ceramics
• /
• 제7권1호
• /
• pp.26-29
• /
• 2001

Indium tin oxide (ITO) films were deposited on glass substrates at $300^{\circ}C$ in oxygen/argon mixtures by RF-enhanced DC-magnetron sputtering and were compared to those by conventional DC magnetron sputtering. The RF enhancement was performed using a coil above an ITO target. X-ray diffraction measurements revealed that RF-enhanced plasma affected the preferred orientation and the crystallinity of the films. The resistivity of the films prepared by RF-enhanced DC-magnetron sputtering was almost constant at oxygen content lower than 0.3% and then increased sharply with increasing oxygen content. However the resistivity of the films by conventional sputtering has little dependence on the oxygen content. Those results can be explained on the basis of the incorporation of oxygen into the ITO films due to the RF enhancement.

• Journal of Ceramic Processing Research
• /
• 제20권1호
• /
• pp.18-23
• /
• 2019

Chemical looping combustion (CLC) is a promising carbon capture and storage (CCS) technology whose efficiency and cost primarily relies on the oxygen carrier materials used. In this paper, gadolinium-doped ceria (GDC, Ce0.9Gd0.1O1.95) was added as a promoter to improve the oxygen transfer rate of MgMnO3-δ oxygen carrier materials. Increasing GDC content significantly increased the oxygen transfer rate of MgMnO3-δ-GDC composites for the reduction reaction due to an increase in the surface adsorption of CH4 via oxygen vacancies formed on the surface of the GDC. On the other hand, the oxygen transfer rate for the oxidation reaction decreased linearly with increasing GDC content due to the oxygen storage ability of GDC. Adsorbed oxygen molecules preferentially insert themselves into oxygen vacancies of the GDC lattice rather than reacting with (Mg,Mn)O to form MgMnO3-δ during the oxidation reaction.

• 펄프종이기술
• /
• 제37권5호통권113호
• /
• pp.50-55
• /
• 2005

In previous report, we investigated the impact of hexeneuronic acid and some residual extractiveson lignin determination. These non-lignin components severely interfered lignin content determination which also affect on the oxygen delignification comparison between aspen and pine unbleached kraft pulps. Very different pattern was observed whether based on uncorrected conventional kappa number or based on corrected kappa number in oxygen delignification comparison. Lower kappa number aspen pulps showed poor response to oxygen delignification when kappa number was used as lignin determination method but better response with using the acid lignin method. Phenolic hydroxyl group in kraft pulps were also compared based on uncorrected or corrected kappa numberfor lignin content. Based on uncorrected kappa number, lower kappa number oxygen-delignified pulps had lower phenolic hydroxyl group. However, lower kappa number oxygen-delignified pulps showed much higher phenolic hydroxyl group based on the corrected lignin content. For accurate comparison for residual lignin properties from different pulps, lignin determination should be corrected from non-lignin components contribution to lignin.

• 한국재료학회지
• /
• 제16권2호
• /
• pp.116-122
• /
• 2006

The effects of milling time in argon and hydrogen atmospheres on the hydrogen sorption speed of a getter alloy, $Zr_{57}V_{36}Fe_{7}$, was studied. The hydrogen sorption speed of milled alloys was evaluated at room temperature. In argon, as the oxygen content increased with milling time, the hydrogen sorption speed decreased accordingly. In hydrogen, on the other hand, the oxygen content decreased at first with milling time but started increasing after 5 hrs of milling time. Similar to the case of argon, however, the hydrogen sorption speed changed exactly in the opposite direction with the oxygen content, exhibiting the maximum rate at 5 hrs. These results suggest that in both atmospheres the hydrogen sorption speeds are inversely related with the oxygen contents.