• Microbiology and Biotechnology Letters
• /
• v.23 no.1
• /
• pp.60-67
• /
• 1995

Methanol assimilating yeast, Hansenula sp. MS-364 that has high productivity with methanol as carbon and energy source has been preserved at dept. of Microbiological engineering. Purification and properties of alcohol oxidase (E.C.1.1.3.13: oxygen oxidoreductase) were investigated in the methanol assimilating yeast, Hansenula sp. MS-364. Alcohol oxidase is related to the catalytic reaction that degrades alcohol to aldehyde and peroxide. The methanol oxidizing enzyme was purified by ammonium sulfate precipitation, DEAE-Sephadex A-50 chromatography and gel filtration on Sepharose 6B from cell-free extract. The purified enzyme preparation gave a single band in the sodium dodesyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). The molecular weight of the enzyme was calculated to be about 576,000 and molecular weight of subunit was also calculated to be 72,000. The optimal pH and temperature of the enzyme reaction were pH 7.5 and 37$\circ$C, respectively. The enzyme was unstable in acidic pH and higher temperature. The enzyme was not specific for methanol and also oxidized lower primary alcohols. The Km value for methanol was 2.5 mM and that for ethanol was 1.66 mM. The enzyme was heavily inhibited by metal ions such as Hg$^{2+}$, Ag$^{2+}$, Cu$^{2+}$. The high concentration of EDTA and sulfhydryl reagents strongly inhibited the enzyme activity. The component of coenzyme was determined to flavin adenine dinucleotide.

• Fashion & Textile Research Journal
• /
• v.5 no.5
• /
• pp.520-528
• /
• 2003

Chitosan was depolymerized by oxidizing agent, hydrogen peroxide ($H_2O_2$) and general properties of resulting low molecular weight chitosan(LMWC) were studied. Effect of amount of $H_2O_2$, ratio of $H_2O_2$/chitosan, and reaction temperature were investigated in preparing LMWC. In addition, the reduction of molecular weight of prepared LMWC were measured after a certain time passage. Pre-swelling treatment of starting chitosan affected uniform and mild reaction of depolymerization and increased the solubility of resulting LMWC. Prepared LMWC (Mw 100,000) showed a decrease in Mw by 25-35%. Prepared LMWC(Mw 60,000-70,000) showed a decrease in Mw by 10-15% after 7 months. Therefore, this depolymerizing process can be concluded desirable in terms of stability. In addition, yellowing of pre-swelling treated chitosan upon time passage was insignificant compared with that of untreated chitosan. Therefore, pre-swelling treatment of chitosan before depolymerization would be beneficial in terms of stability of physical state.

• Corrosion Science and Technology
• /
• v.3 no.6
• /
• pp.227-232
• /
• 2004

The carboxylates as a corrosion inhibitor has been studied by many researchers because of its environmental safety and low depletion rate. However, conventional test methods of inhibitor such as weight loss measurements, linear polarization resistance and corrosion potential monitoring etc., evaluate uniform corrosion of metals. These methods are unable to evaluate crevice-related corrosions, which are encountered in most of heat exchanging facilities. In order to choose the optimum corrosion inhibitor, the appropriate test methods are required to evaluate their performances in service environment. From this point of view, polarization technique was used to evaluate the characteristics of sodium heptanoate on corrosion behavior for carbon steel. Especially a thin film crevice sensor technique were applied to simulate the crevice corrosion in this study. From these experiments, we found that oxygen as an oxidizing agent was required to obtain stable passive film on the metal. Presence of oxygen, however, accelerated crevice corrosion. Potential shift by oxygen depletion and weakened inhibitive film inside the crevice were responsible for such accelerated feature. It is shown that film for corrosion inhibition is a mixture of sodium heptanoate and iron (II) heptanoate as reaction product of iron surface and sodium heptanoate. The iron (II) heptanoate which has been synthesized by reaction of heptanoic acid and ferrous chloride in methanol solution forms bidentate complex.

• Journal of the Korean Chemical Society
• /
• v.34 no.6
• /
• pp.534-538
• /
• 1990

Chromium(Ⅵ) compound, [$C_9H_7$NH]$_2Cr_2O_7$ has been prepared by the reaction of isoquinoline with chromium trioxide under the presence of water. [$C_9H_7$NH]$_2Cr_2O_7$ is nonhydroscopic and dissolved in water very well. Structure of [$C_9H_7$NH]$_2Cr_2O_7$ is identified by FTIR spectra and elemental analysis data. The ability of [$C_9H_7$NH]$_2Cr_2O_7$ for the oxidation of alcohols were examined in methylene chloride. [$C_9H_7$NH]$_2Cr_2O_7$ was found as efficient oxidizing agent for the conversion of allyl, primary and secondary alcohols to the corresponding aldehydes or ketones.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.11
• /
• pp.3544-3550
• /
• 2012

Cetrizine dihydrochloride (CTZH) is widely used as an anti-allergic drug. Sodium N-bromo-p-toluenesulfonamide or bromamine-T (BAT) is the bromine analogue of chloramine-T (CAT) and is found to be a better oxidizing agent than CAT. In the present research, the kinetics of oxidation of CTZH with BAT in acid and alkaline media was studied at 313 K. The experimental rate laws obtained are: -d[BAT]/dt=$k[BAT][CTZH]^{0.80}[H^+]^{-0.48}$ in acid medium and -d[BAT]/dt=$k[BAT][CTZH]^{0.48}[OH^-]^{0.52}[PTS]^{-0.40}$ in alkaline medium where PTS is p-toluenesulfonamide. Activation parameters and reaction constants were evaluated. The solvent isotope effect was studied using $D_2O$. The dielectric effect is positive. The stoichiometry of the reaction was found to be 1:1 and the oxidation products were identified as 4-chlorobenzophenone and (2-piperazin-1-yl-ethoxy)-acetic acid in both media. The rate of oxidation of CTZH is faster in acid medium. Suitable mechanisms and related rate laws have been worked out.

• Journal of Environmental Science International
• /
• v.30 no.12
• /
• pp.1005-1014
• /
• 2021

Organic contaminants can be released into water environments due to chemical accidents and exist as dissolved and non-aqueous phase liquids (NAPL). Fenton oxidation was tested for bisphenol A and nitrobenzene as model organic contaminants in dissolved and NAPL states. Fenton oxidation was successfully applied for both of the dissolved and NAPL states of the two pollutants and the results indicated that a quick treatment was needed to reduce the risk from a chemical accidents instead of carrying out oxidation after the contaminants dissolve in water. A set of Fenton reactions were tested under seawater conditions because chemical accidents often occurs in the ocean. Chloride ions act as radical scavengers and inhibit Fenton oxidation. The reaction rate is inversely proportional to salt contents and the reduced reaction rate can be compensated by increasing the quantity of the oxidizing agents. The current study showes that Fenton oxidation could be applied as a quick treatments for organic contaminant in dissolved and NAPL state organic contaminants released as a result of leaks or chemical accidents.

• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.2_2
• /
• pp.397-402
• /
• 2024

Silicon carbide materials undergo an oxidation reaction in a high-temperature oxidizing environment and show different characteristics depending on the test temperature and time. In particular, the added oxides form a secondary phase within the sintering process and exhibit different oxidation characteristics depending on the added sintering materials. Therefore, to evaluate the oxidation characteristics, the weight of the test piece and the thickness of the oxidation layer were observed, and the structure and oxidation characteristics of the material were analyzed using SEM. SEM observation showed that an oxide layer was formed on the surface of the liquid sintered silicon carbide material after it was oxidized at 1200 ℃, 1300 ℃, and 1400 ℃ for 10 hours, respectively. Then, a bending test was performed at each temperature on the test piece with the oxidation layer formed to evaluate the change in flexural strength. The strength was 466.6 MPa at 1200 ℃, 363.1 MPa at 1300 ℃, and 350.8 MPa at 1400 ℃. Al₂O₃-SiO₂ oxidized at 1200 ℃ for 10 hours showed an increase in strength of about 21.0 MPa compared to the data before the oxidation test.

• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.3
• /
• pp.341-349
• /
• 2010

It is well known that manganese is hard to oxidize under neutral pH condition in the atmosphere while iron can be easily oxidized to insoluble iron oxide. The purpose of this study is to identify removal mechanism of manganese in the D water treatment plant where is treating bank filtered water in aeration and rapid sand filtration. Average concentration of iron and manganese in bank filtered water were 5.9 mg/L and 3.6 mg/L in 2008, respectively. However, their concentration in rapid sand filtrate were only 0.11 mg/L and 0.03 mg/L, respectively. Most of the sand was coated with black colored manganese oxide except surface layer. According to EDX analysis of sand which was collected in different depth of sand filter, the content of i ron in the upper part sand was relatively higher than that in the lower part. while manganese content increased with a depth. The presence of iron and manganese oxidizing bacteria have been identified in sand of rapid sand filtration. It is supposed that these bacteria contributed some to remove iron and manganese in rapid sand filter. In conclusion, manganese has been simultaneously removed by physicochemical reaction and biological reaction. However, it is considered that the former reaction is dominant than the latter. That is, Mn(II) ion is rapidly adsorbed on ${\gamma}$-FeOOH which is intermediate iron oxidant and then adsorbed Mn(II) ion is oxidized to insoluble manganese oxide. In addition, manganese oxidation is accelerated by autocatalytic reaction of manganese oxide. The iron and manganese oxides deposited on the surface of the sand and then are aged with coating sand surface.

• Applied Microscopy
• /
• v.33 no.1
• /
• pp.17-23
• /
• 2003

Indium oxide ($In_2O_3$) nanowires were successfully synthesized by a simple reaction in a wet oxidizing environment at low temperature without metal catalyst. The nanowires were characterized by an x-ray diffraction (XRD), a scanning electron microscopy (SEM) equipped with an energy dispersive spectrometry (EDS), and a transmission electron microscopy (TEM). It was shown that the $In_2O_3$ nanowires were two types of morphology, uniform nanowires and nanowires containing $In_2O_3$ nanoparticles in its stem. It was found that lengths of the nanowires were ranges of several micrometers and their diameters were around $10{\sim}250$ nm. The growth direction of the nanowires was investigated and their growth mechanism is also discussed.

• Resources Recycling
• /
• v.30 no.2
• /
• pp.53-60
• /
• 2021

Leaching experiments from single metal and metallic mixtures were conducted to develop a process for the recovery of cobalt, copper, and nickel in spent lithium ion batteries. Inorganic and organic acid solutions without oxidizing agents were employed. No copper was dissolved in the absence of an oxidizing agent in the leaching solutions. The leaching condition to completely dissolve single metal of cobalt and nickel was determined based on acid concentration, reaction temperature and time, and pulp density. The leaching condition to dissolve all of cobalt and nickel from the metallic mixtures was also obtained. Leaching of the metallic mixture with methanesulfonic acid led to selective dissolution of cobalt at low temperatures.