• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.6
• /
• pp.502-507
• /
• 2007

The oxidation treatment of several carbon materials with a sodium chlorate and 70 wt.% of nitric acid, combined with heat treatment, were attempted to achieve an electrochemical active material with a larger capacitance. Among pitch, needle coke, calcinated needle coke and natural graphite, the structure of needle coke and calacinated needle coke were changed to the graphite oxide structure with the expansion of the inter-layer. On the other hand, the calcinated needle coke after oxidation and heating at $200^{\circ}C$ has exhibited largest capacitance per weight and volume of 29.5 F/g and 24.5 F/ml at the two-electrode system in the potential range of 0 to 2.5 V. The electrochemical performance of the calcinated needle coke was discussed with the phenomenon of the electric field activation and the formation of new pores between the expanded inter-layer at first charge.

• Korean Journal of Materials Research
• /
• v.16 no.12
• /
• pp.766-770
• /
• 2006

The frictional behavior of oxide films on top of the plasma nitrocarburized compound layers was investigated in terms of post-oxidation treatment temperatures. The post-oxidation treatment at both temperatures($400^{\circ}C,\;500^{\circ}C$) produced magnetite($Fe_3O_4$) films which led to a significant enhancement in corrosion resistance. However, this process did not result in any improvement in frictional behavior of the nitrocarburized surface. The wear mechanisms were governed predominantly by the abrasive action of the slider on the surface irrespective of the counterface material(SiC and Bearing steel). When the specimen was sliding against a SiC counterface, the oxide films were destroyed during the early stage of the sliding process and the wear debris of the oxide film at the sliding track had a great influence on the friction coefficient. On the other hand, when sliding against a bearing steel counterface, the slider was mainly worn out due to the much higher hardness of the surface hardened layer. The fluctuation of the friction coefficient of $400^{\circ}C$-oxidized/ nitrocarburized specimen is much severer than that of $500^{\circ}C$ specimen, due to the less amount of wear debris.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.5
• /
• pp.805-810
• /
• 2007

Molecular recognition for a specific cation depending on the change of the oxidation state of the metal catalyst component contained in the hydrogel network has been studied in a self-oscillating hydrogel. The selfoscillating hydrogels are synthesized by the copolymerization of N-isopropylacrylamide (NIPAAm), lead methacrylic acid (Pb(MAA)2), and Ru(bpy)3 2+ monomer as a metal catalyst component. The recognition for a specific cation (in this study, Ca2+ has been used) is characterized by the adsorbed amount of Ca2+ into the gel. The recognition of the gels for Ca2+ is higher at the temperature below the LCST, and also higher at the oxidized state than at reduced state of the metal catalyst component which corresponds to a more swollen state. Moreover, a propagating wave induced by a periodic change of the oxidation state with the diffusion phenomena in the oscillating hydrogel shows a possibility for temporal and site-specific molecular recognition due to the local swelling of the gel.

• Journal of Conservation Science
• /
• v.34 no.5
• /
• pp.369-377
• /
• 2018

In order to examine the constituents and weathered state of a lacquer specimen, analysis of the organic materials was conducted using py/GC/MS(pyrolysis-gas chromatography-mass spectrometry). The samples were obtained from the lacquered wooden sheath of a long ring-pommel sword excavated in the Imdang No.1 ancient tomb constructed around the Proto-Three Kingdoms period. In direct py/GC/MS, the sample and the dried Asian lacquer showed similar chromatograms, while the characteristic compounds of Asian lacquer such as 1,2-dimethoxy-3-pentadecylbenzene were observed in THM(thermally assisted hydrolysis and methylation)-py/GC/MS. In addition, compounds like dimethyl nonanedioate, which presumably originated from drying oil, were also detected. Furthermore, the detection of oxidized catechols in considerable amount indicated that the degradation of lacquer is estimated to result from the oxidation of urushiol. Therefore, it is suggested that the lacquered wooden sheath was prepared using Asian lacquer and drying oil, and that the lacquer layer was considerably oxidized over the long burial time.

• Nuclear Engineering and Technology
• /
• v.43 no.4
• /
• pp.391-398
• /
• 2011

The U metal chips generated in developing nuclear fuel and a gamma radioisotope shield have been stored under immersion of water in KAERI. When the water of the storing vessels vaporizes or drains due to unexpected leaking, the U metal chips are able to open to air. A new oxidation treatment process was raised for a long time safe storage with concepts of drying under vacuum, evaporating the containing water and organic material with elevating temperature, and oxidizing the uranium metal chips at an appropriate high temperature under conditions of controlling the feeding rate of oxygen gas. In order to optimize the oxidation process the uranium metal chips were completely dried at higher temperature than $300^{\circ}C$ and tested for oxidation at various temperatures, which are $300^{\circ}C$, $400^{\circ}C$, and $500^{\circ}C$. When the oxidation temperature was $400^{\circ}C$, the oxidized sample for 7 hours showed a temperature rise of $60^{\circ}C$ in the self-ignition test. But the oxidized sample for 14 hours revealed a slight temperature rise of $7^{\circ}C$ representing a stable behavior in the self-ignition test. When the temperature was $500^{\circ}C$, the shorter oxidation for 7 hours appeared to be enough because the self-ignition test represented no temperature rise. By using several chemical analyses such as carbon content determination, X-ray deflection (XRD), Infrared spectra (IR) and Thermal gravimetric analysis (TGA) on the oxidation treated samples, the results of self-ignition test of new oxidation treatment process for U metal chip were interpreted and supported.

• Carbon letters
• /
• v.18
• /
• pp.18-23
• /
• 2016

Polyacrylonitrile (PAN)-based carbon fibers have high specific strength, elastic modulus, thermal resistance, and thermal conductivity. Due to these properties, they have been increasingly widely used in various spheres including leisure, aviation, aerospace, military, and energy applications. However, if exposed to air at high temperatures, they are oxidized, thus weakening the properties of carbon fibers and carbon composite materials. As such, it is important to understand the oxidation reactions of carbon fibers, which are often used as a reinforcement for composite materials. PAN-based carbon fibers T300 and T700 were isothermally oxidized in air, and microstructural changes caused by oxidation reactions were examined. The results showed a decrease in the rate of oxidation with increasing burn-off for both T300 and T700 fibers. The rate of oxidation of T300 fibers was two times faster than that of T700 fibers. The diameter of T700 fibers decreased linearly with increasing burn-off. The diameter of T300 also decreased with increasing burn-off but at slower rates over time. Cross-sectional observations after oxidation reactions revealed hollow cores in the longitudinal direction for both T300 and T700 fibers. The formation of hollow cores after oxidation can be traced to differences in the fabrication process such as the starting material and final heat treatment temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.195-196
• /
• 2009

This paper describes the fabrication and characteristics of polycrystalline 3C-SiC thin film diodes for extreme environment applications, in which the this thin film was deposited onto oxidized Si wafers by APCVD using HMDS In this work, the optimized growth temperature and HMDS flow rate were $1,100^{\circ}C$ and 8sccm, respectively. A Schottky diode with a Au, Al/poly 3C-SiC/$SiO_2$/Si(n-type) structure was fabricated and its threshold voltage ($V_d$), breakdown voltage, thickness of depletion layer, and doping concentration ($N_D$) values were measured as 0.84V, over 140V, 61nm, and $2.7{\times}10^{19}cm^2$, respectively. To produce good ohmic contact, Al/3C-SiC were annealed at 300, 400, and $500^{\circ}C$ for 30min under a vacuum of $5.0{\times}10^{-6}$Torr. The obtained p-n junction diode fabricated by poly 3C-SiC had similar characteristics to a single 3C-SiC p-n junction diode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.197-198
• /
• 2009

This paper describes the Raman scattering characteristics of polycrystalline (poly) 3C-SiC films, which were deposited on the thermally oxidized Si(100) substrate by the atmosphere pressure chemical vapor deposition (APCVD) method according to growth temperature. TO and LO phonon modes to 2.0m thick poly 3C-SiC deposited at $1180^{\circ}C$ were measured at 794.4 and $965.7\;cm^{-1}$ respectively. From the intensity ratio of $I_{(LO)}/I_{(TO)}$ 1.0 and the broad full width half maximum (FWHM) of TO modes, itcan be elucidated that the crystallinity of 3C-SiC forms polycrystal instead of disordered crystal and the crystal defect is small. At the interface between 3C-SiC and $SiO_2$, $1122.6\;cm^{-1}$ related to C-O bonding was measured. Here poly 3C-SiC admixes with nanoparticle graphite with the Raman shifts of D and G bands of C-C bonding 1355.8 and $1596.8\;cm^{-1}$. Using TO mode of 2.0 m thick poly 3C-SiC, the biaxial stress was calculated as 428 MPa.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.2
• /
• pp.66-70
• /
• 2006

Various kind of structural defects are observed to be present on the oxidized surface of the silicon crystal which was previously damaged mechanically. The formation of such defects was found to depend on the amount of damage induced and the temperature of thermal oxidation. It was confirmed by the measurement of minority carrier life time that gettering capability decreases as the size of the defects increase. The strained layer which is formed due to smaller amount of damage or lower oxidation temperature believed to has higher capability of gettering over defects like dislocation loops or stacking faults.

• Journal of Conservation Science
• /
• v.35 no.4
• /
• pp.269-277
• /
• 2019

Seaweed extracts, namely carrageenan obtained from Grateloupia elliptica and algin obtained from Laminaria, were employed as adhesive agents to synthesize solid adhesives for paper. Carrageenan from Grateloupia elliptica with the highest adhesive strength and lgin from Laminaria with the highest compressive strength was selected. The selected carrageenan and algin were mixed in a ratio of 7:3, and the mixture was employed as an adhesive agent. At a high temperature, sodium stearate(used as a solidifying material) oxidized the seaweed extracts. Consequently, carrageenan and algin were added to the final manufacturing process. The adhesive strength of the final synthesized solid adhesive is found to be 3.02 MPa and the compressive strength is found to be 30.5 N. Compared to the adhesive strength (2.95 MPa) and compressive strength (30.11 N) of commercial solid adhesives, the obtained results indicate superior adhesion characteristics. Furthermore, the proposed adhesive is environment-friendly because the presence of volatile organic compounds, formaldehyde, and heavy metals(such as chromium, lead, and cadmium) were not detected. Moreover, when used, the flatness of paper was twice that of commercial solid paper adhesives. Hence, the proposed adhesive can provide excellent adhesion, stability, and usability.