• 한국주조공학회지
• /
• 제40권6호
• /
• pp.135-145
• /
• 2020

Aluminum cast iron has excellent oxidation resistance, sulfurization resistance, and corrosion resistance. However, the ductility at room temperature is insufficient, and at temperatures above 600?, the strength drops sharply and practicality is limited. In the case of heat-resistant cast iron, high-temperature materials containing Cr and Ni account for 30 to 50% or more. However, these high-temperature materials are expensive. Aluminum heat-resistant cast iron is considered as a substitute for expensive heat-resistant materials. Oxidation due to the aging temperature and holding time conditions increases more in 0 wt.% Al-cast iron than in 2 and 4 wt.% Al-cast iron according to oxidized weight and gravimetric oxide layer thickness measurements. As a result of observing the cross-section of the oxide layer, it was found to contain 0 wt.% of Al-cast iron silicon oxide-containing SiO₂ or Fe₂SiO₄ oxide film. In cast iron containing aluminum, the thickness of the internal oxide layer due to aluminum increases as the aging temperature and retention time increase, and the amount of the iron oxide layer generated on the surface decreases.

• 한국주조공학회지
• /
• 제34권6호
• /
• pp.194-199
• /
• 2014

The effect of $Al_2Ca$ on the oxidation resistance and tensile property of Al-5Mg alloys was investigated. According to the TGA (Thermogravimetric analysis) result at $550^{\circ}C$ after 24hrs, the Al-5Mg alloy showed parabolic behavior with weight gain. On the other hand, there was almost no difference in the weight changes of the $Al_2Ca$ added Al-5Mg alloys during the oxidation. It was thought that the improvement of oxidation resistance in $Al_2Ca$ added Al-5Mg alloys might be due to the formation of a protective oxide layer with CaO and MgO on the surface. The microstructures of the alloys showed grain refinement with an increasing $Al_2Ca$ content. From the tensile test, the yield strength of the alloys were improved with an increasing $Al_2Ca$ content. The 0.07 mass%$Al_2Ca$ added Al-5Mg alloy showed similar elongation and increased strength, simultaneously. It was considered that the addition of $Al_2Ca$, which was superior in the oxidation resistance of Al, reduced the formation of Mg oxides and inclusions during the alloying. This, partly led to the improvement of tensile properties.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.429-429
• /
• 2012

To investigate the gettering effect of B-doped n-type monocrystalline silicon wafer, we made the p-n junction by diffusing boron into n-type monocrystalline Si substrate and then oxidized the boron doped n-type monocrystalline silicon wafer by in-situ wet and dry oxidation. After oxidation, the minority carrier lifetime was measured by using microwave photoconductance and the sheet resistance by 4-point probe, respectively. The junction depth was analyzed by Secondary Ion Mass Spectrometry (SIMS). Boron diffusion reduced the metal impurities in the bulk of silicon wafer and increased the minority carrier lifetime. In the case of wet oxidation, the sheet resistance value of ${\sim}46{\Omega}/{\Box}$ was obtained at $900^{\circ}C$, depostion time 50 min, and drive-in time 10 min. Uniformity was ~7% at $925^{\circ}C$, deposition time 30 min, and drive-in time 10 min. Finally, the minority carrier lifetime was shown to be increased from $3.3{\mu}s$ for bare wafer to $21.6{\mu}s$ for $900^{\circ}C$, deposition 40 min, and drive-in 10 min condition. In the case of dry oxidation, for the condition of 50 min deposition, 10 min drive-in, and O2 flow of 2000 SCCM, the minority carrier lifetime of 16.3us, the sheet resistance of ${\sim}48{\Omega}/{\Box}$, and uniformity of 2% were measured.

• 센서학회지
• /
• 제22권4호
• /
• pp.239-243
• /
• 2013

Several methods are available to measure the oxidation of edible oils, such as their acid, peroxide, and anisidine values. However, these methods require large quantities of reagents and are time-consuming tasks. Therefore, a more convenient and time-saving way to measure the oxidation of edible oils is required. In this study, an edible oil-condition sensor was fabricated using single-walled nanotubes (SWNTs) made using the spray deposition method. SWNTs were dispersed in a dimethylformamide solution. The suspension was then sprayed using a spray gun onto a prefabricated Au/Ti electrode. To test the sensor, oxidized edible oils, each with a different acid value, were prepared. The SWNT sensors were immersed into these oxidized oils, and the resistance changes in the sensors were measured. We found that the conductivity of the sensors decreased as the oxidation level of the oil increased. In the case of the virgin oil, the resistance change ratio in the SWNT sensor S(%) = {[(Rf - Ri)]/Ri}(%) was more than 40% after immersion for 1 min. However, in the case of the oxidized oil, the resistance change ratio decreased to less than that of the response of the virgin oil. This result suggests that the change in the oil components induced by the oxidation process in edible oils is related to the conductivity change in the SWNT sensor.

• Journal of Welding and Joining
• /
• 제29권5호
• /
• pp.58-62
• /
• 2011

Stainless steels are alloy steels with a nominal chromium content of at least 11 percent, with other alloy additions. The stainlessness and corrosion resistance of these alloy steels are attributed to the presence of a passive oxide film on the surface. When exposed to conditions like Resistance Spot Welding (RSW) process that remove the passive oxide film, stainless steels are subject to corrosive attack. And exposure to elevated temperatures causes oxidation (discoloration) of areas around indentation in Spot welding. In this paper, deal with the effect of shielding gas (Ar) preventing the corrosion, oxidation of stainless steel. And find the optimal shielding gas flow rate. In addition, suggest effective purging method for direct/indirect spot welding process.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.857-858
• /
• 2006

In order to clarify the wear resistance as cutting tools, the effect of oxygen addition on oxidation behavior of the ${\beta}-Si_3N_4$ ceramics with 5 mass% $Y_2O_3$ and 2 or 4 mass% $Al_2O_3$ was investigated by performing oxidation tests in air at $1300^{\circ}$ to $1400^{\circ}C$ and cutting performance tests. From test results, we could conclude that the mechanical properties of ${\beta}-Si_3N_4$ ceramics depending on oxygen introduction are much effective on cutting performance improvements of ${\beta}-Si_3N_4$ ceramics.

• 한국세라믹학회지
• /
• 제41권9호
• /
• pp.657-662
• /
• 2004

마그카본계 내화물의 산화저항성을 증대시키기 위하여 섭씨 100$0^{\circ}C$에서 120$0^{\circ}C$에서 산화기구를 조사하고, TiC를 첨가하여 산화저항성 증가에 대한 효과를 관찰하였다. 산소공급을 위해 공기를 분당 0.2리터의 속도로 흘려주었으며 열천칭으로 무게변화가 없어질 때까지 매 30초 간격마다 무게감소를 측정하였다 본 실험에서 사용된 마그카본계 시편의 산화거동과 관련한 유효확산 계수는 1.39${\times}$$10^{-4}$ $m^2$/sec이다. 이러한 실험조건에서 총체적인 산화공정은 산화된 기공층을 통하여 내부로 향하는 산소의 확산에 의해 지배되는 반응으로 해석할 수 있다. TiC를 첨가한 시편은 마그카본계 내화물의 산화 저항성을 증대시켰다.

• 한국표면공학회지
• /
• 제29권4호
• /
• pp.268-277
• /
• 1996

Boronizing treatment of Microalloyed steel has been investigated by mean of Boronizing paste mainly consisted of $B_4C$ at various temperatures and times. The micro hardness of the boride layers were about HV 1200~1500. The thickness of the boride layer were increased with an increase of square root of treatment time at constant temperature. The activation energy for diffusion of boron in the specimen obtained from the slope of Arrhenius plots was 254 kJ/mol, but 197 kJ/mol for the induction heated specimen. The boride layer had a good corrosion resistance in solutions of 20% HCl and 20% $H_2SO_4$, solution. In 20% $HNO_3$ solution, however, its corrosion resistance increased. The boride layer had a good high temperature oxidation resistance at below $800^{\circ}C$, but at temperature above $900^{\circ}C$, the oxidation resistance decreased as the oxidation temperature.

• Corrosion Science and Technology
• /
• 제19권3호
• /
• pp.138-145
• /
• 2020

Immersion tests of Alloy 600 were conducted in simulated primary water environments of a pressurized water reactor at 325 ℃ for 10, 100, and 1000 h to obtain insight into effects of surface deformation on internal and intergranular (IG) oxidation behavior through precise characterization using various microscopic equipment. Oxidized samples after immersion tests were covered with polyhedral and filamentous oxides. It was found that oxides were abundant in mechanically ground (MG) samples the most. The number density of surface oxides increased with time irrespective of the method of surface finish. IG oxidation occurred in mechanically polished (MP) and chemically polished (CP) samples with thin internal oxidation layers. However, IG oxidation was suppressed with relatively thick internal oxidation layers in MG samples compared to MP and CP samples, suggesting that MG treatment could increase resistance to primary water stress corrosion cracking (PWSCC) from the standpoint of IG oxidation. As a result, appropriate surface treatment for Alloy 600 could prevent oxygen diffusion into grain boundaries, inhibit IG oxidation, and finally induce its high PWSCC resistance.

• 한국주조공학회지
• /
• 제25권6호
• /
• pp.226-232
• /
• 2005

Contact material is widely used in the field of electrical parts. Ag-CdO material has a good wear resistance and stable contact resistance. In order to establish optimizing heat treatment condition, rolling temperature and oxidation process, we studied the microstructure of Ag-CdO material with various conditions. The experimental procedure were melting using high frequency induction, heat treatment, rolling and internal oxidation. And we experimented on difference process, Post-oxidaion. In this study, we obtained the optimizing heat treatment condition was $700^{\circ}C$ for 15 min. and the optimizing rolling temperature was $730^{\circ}C$. In investigation of the microstructure of oxidized material, coarse oxide and depleted oxidation layer existed. The hardness was average Hv 70. When we used Post-oxidation, oxides were finer than prior process and depleted oxidation layer did not exist. The hardness of Post-oxidation material was average Hv 80. And the optimizing rolling temperature was $800^{\circ}C$.